Advertisement
Quick Links
Roll-Over Protection System Kit
2009 or 2010 TITAN
Model No. 121-2984
Installation
Note: Determine the left and right sides of the machine from the normal operating position.
Shutoff the engine and wait for all moving parts to stop.
Installing the Rollbar Supports
Complete the following steps for both left and right rollbar
supports.
Note: If preferred, the rear wheels may be removed for
easier access to the brace.
1. Loosely secure the brace and seat belt bracket to the
frame with a bolt (1/2 x 1-1/4 inches) and locknut
(Figure
1) allowing it to swing freely.
5
8
6
7
4
3
2
1
1. Locknut
2. Reinforcing bracket
3. Hex nut
4. Small rubber bumper
5. Rollbar support
6. Brace
7. Bolt (1/2 x 1-1/4 inches)
and locknut
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
9
14
G017616
Figure 1
8. Seat belt
9. Cutout faces the rear
10. Flange-head bolt and
locknut
11. Seat-belt bracket
12. Bolt (1/2 x 3-1/2 inches)
13. Large washers
14. Bolt (1/2 x 4-1/2 inches)
Register at www.Toro.com.
®
ZX Zero-Turn-Radius Riding Mower
2. Loosely attach the rollbar support and reinforcing
bracket to the frame using a bolt (1/2 x 4-1/2 inches),
washer, and locknut as shown in
Note: Ensure that the cutout at the top of the rollbar
support faces the rear of the machine.
3. Attach the brace to the rollbar support with a bolt (1/2
x 3-1/2 inches), washer, and hex nut
Note: Note the orientation of the reinforcing bracket.
4. Attach the seat belt assembly to the seat belt bracket
with a flange-head bolt and locknut
Attaching the Pivot Brackets
Assemble the pivot brackets to the rollbar as shown in
2. Leave the bolts loose enough that the parts are free to
10
shift around.
Note: Ensure that the locknuts are on the inside of the
support tube.
11
12
13
1. Bolt (1/2 x 3-1/2 inches)
2. Flat washer
3. Pivot bracket, notch facing
up
Form No. 3398-629 Rev A
Installation Instructions
Figure
Figure 2
4. Flat spacer
5. Flange locknut
6. Rollbar, cutout facing
down
Original Instructions (EN)
All Rights Reserved *3398-629* A
Printed in the USA
1.
(Figure
1).
(Figure
1).
Figure
Advertisement
Related Manuals for Toro 121-2984
Summary of Contents for Toro 121-2984
- Page 1 Roll-Over Protection System Kit 2009 or 2010 TITAN ® ZX Zero-Turn-Radius Riding Mower Model No. 121-2984 Installation Instructions Installation Note: Determine the left and right sides of the machine from the normal operating position. Shutoff the engine and wait for all moving parts to stop.
- Page 2 Attaching the Rollbar 1. Insert the cylindrical spacer in the pivot holes in both rollbar supports (Figure Figure 5 g017619 1. Rollbar 3. Hairpin Figure 3 2. Pivot pin 4. Rollbar, upright and locked 1. Cylindrical spacer Making the Final Adjustments 2.
- Page 3 the rollbar and verify that the cylindrical spacers are correctly installed as previously described in Attaching the Rollbar (page 4. If the conical rubber bumpers are not pre-installed do the following: Unlock the rollbar and put it in the down position.
- Page 4 Using the Rollover Protection G015035 System (ROPS) WARNING There is no rollover protection when the roll bar is in the down position, and injury or death may result. • Keep the roll bar in the raised and locked Figure 8 position and wear the seat belt.