Advertisement
48 and 54 inch Bagger Finishing Kit
2011 and After TITAN Series Zero-Turn-Radius Riding Mower
Model No. 120-7122
Model No. 120-7123
This kit requires the Bagger Kit 79326 to complete installation. For
all TITAN Series mowers, begin Finishing Kit installation before
installing the bagger kit. Contact your Authorized Service Dealer
or Toro Customer Service to obtain the necessary parts. For more
information, visit us at www.Toro.com.
Safety
Important: The ROPS roll bar is an integral and
effective safety device. Keep the roll bar in the
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of
potential danger. Replace any decal that is damaged or lost.
110-6691
1. Thrown object hazard—keep bystanders a safe distance
from the machine.
2. Thrown object hazard, mower—do not operate without the
deflector, discharge cover, or grass collection system in
place.
3. Cutting/dismemberment of hand or foot—stay away from
moving parts.
© 2011—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
fully raised and locked position when operating the
mower. Lower the roll bar temporarily only when
absolutely necessary.
Register at www.Toro.com.
Form No. 3369-688 Rev A
Installation Instructions
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 120-7122
Summary of Contents for Toro 120-7122
- Page 1 This kit requires the Bagger Kit 79326 to complete installation. For all TITAN Series mowers, begin Finishing Kit installation before installing the bagger kit. Contact your Authorized Service Dealer or Toro Customer Service to obtain the necessary parts. For more information, visit us at www.Toro.com. Safety fully raised and locked position when operating the mower.
-
Page 2: Installation
Installation G010701 Installing the Weight Parts needed for this procedure: Figure 2 Weight 1. Cutaway of the front of the 3. Weight Adhesive bumper machine frame 2. Bumper 4. Rest the weight here during install Washer Hair pin Important: Whenever you remove the bagger attachment, remember to remove the front weight Procedure to return the proper stability to the machine. - Page 3 G016263 Installing the Bagger Frame Parts needed for this procedure: Bagger frame (discard frame in bagger kit) Bagger frame support bracket (discard bracket in bagger kit) Figure 4 Self tapping screw (5/16 x 3/4 inch) (included in 1. Support bracket 2.
-
Page 4: Installing The Chute
Installing the Chute Parts needed for this procedure: Straight baffle (48 inch decks only) Curved baffle (54 in decks only) Lock nut (5/16 inch) Hand knob Washer Chute G010581 Figure 6 Left side shown Procedure 1. Bagger frame 4. Hair pin Use this procedure when installing the Finishing Kit on 2. - Page 5 4. Install the chute to the deck making sure the opening in top of the chute aligns with the exposed post on the deck top (Figure 9). G010637 Figure 7 1. Deflector assembly 5. Lock nut (existing) G010638 2. Fasteners (existing), retain 6. Forward hole 3.
- Page 6 2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 12). Installing the Bagger Top Parts needed for this procedure: Circular cotter pin Procedure 1. Install the bagger top to the bagger frame. Slide the brackets over the posts in the bagger frame and install the circular cotter into the hole in the right hand post (Figure 11).
-
Page 7: Installing The Blades
Connecting with the Discharge Installing the Blades Tube Parts needed for this procedure: No Parts Required Hi-Lift blade Procedure Procedure 1. Slide the curved end of the discharge tube into the 1. Remove the existing mower blades installed on your opening in the bagger top (Figure 14). -
Page 8: Maintenance
Maintenance Removing the Finishing Kit Whenever the bagger kit is removed, the finishing kit should be removed using the following procedure. Retain all parts for future installation. CAUTION Removing the bagger changes the weight distribution of the machine. Operating the machine with the front weights installed without the bagger may cause an unstable condition which could result in a loss of control.