Related Manuals for Fujitsu SK-91460T-144PMC-GPIO
Summary of Contents for Fujitsu SK-91460T-144PMC-GPIO
-
Page 1: Evaluation Board
Fujitsu Microelectronics Europe FMEMCU-UG-910074-11 User Guide MB91460 SERIES EVALUATION BOARD SK-91460T-144PMC-GPIO USER GUIDE... -
Page 2: Revision History
SK-91460T-144PMC-GPIO User Guide Revision History Revision History Date Issue 2008/05/15 MHe - Initial version V1.0 2008/06/12 MHe - Itypos corrected V1.1 This document contains 47 pages. FMEMCU-UG-910074-11 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-91460T-144PMC-GPIO Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in... -
Page 4: Table Of Contents
CAN Connector (X7-X8) ..................26 USER-LEDs & optional LC-Display ............... 27 In-Circuit-Programming Connector (X1) ..............28 5 GETTING STARTED...................... 29 Introduction to Softune Workbench ............... 29 Project Start-up ..................... 31 Softune Workbench Debugger ................33 FMEMCU-UG-910074-11 - 4 - © Fujitsu Microelectronics Europe GmbH... - Page 5 7 TROUBLESHOOTING ....................39 8 APPENDIX ........................40 Related Products....................40 Information in the WWW..................41 Tables ........................42 Figures ........................43 Abbreviations ......................44 9 CHINA-ROHS REGULATION ..................45 10 RECYCLING ........................47 © Fujitsu Microelectronics Europe GmbH - 5 - FMEMCU-UG-910074-11...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The SK-91460T-144PMC-GPIO is a multifunctional evaluation board for the Fujitsu 32-bit FR60 Flash microcontroller series MB91460. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: General Description
SK-91460T-144PMC-GPIO User Guide Chapter 1 Overview 1.3 General Description The SK-91460T-144PMC-GPIO supports the 32-bit Flash microcontroller MB91F467TA. It can be used as a stand-alone evaluation board or as a target board for the emulator debugger. The evaluation board supports the following package: FPT-144P-M08. - Page 8 Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems then please loosen the screws and tighten again the screws equally. Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will contaminate inside of connector. FMEMCU-UG-910074-11 - 8 - © Fujitsu Microelectronics Europe GmbH...
-
Page 9: Installation
When turning on the system, be sure to use the following power-up sequence: 1. Power up the Emulator Main Unit (MB2198-01) 2. Power up the Adapter Board (EMA-MB91V460A-002B-80) 3. Power up the target Board (SK-91460T-144PMC-GPIO) To turn off the system, switch off the components in reverse order, beginning with the target board. -
Page 10: Default Jumper Settings For Sk-Mb91460T-144Pmc-Gpio
Reset by UART7 Jumper 2 pin Open L 14 JP44 UART6: RTS-CTS Jumper 2 pin Closed JP45 UART7: RTS-CTS Jumper 2 pin Closed M 12 JP48 SIN6: RS232 / LIN Jumper 3 pin FMEMCU-UG-910074-11 - 10 - © Fujitsu Microelectronics Europe GmbH... - Page 11 UART4: DTR/RTS Jumper 3 pin Open JP90 SDA1 Pullup Jumper 2 pin Open JP92 SCL1 Pullup Jumper 2 pin Open JP104 MD3, fast clock input Jumper 3 pin Table 2-1: Jumper Settings © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-910074-11...
-
Page 12: Jumper Location
SK-91460T-144PMC-GPIO User Guide Chapter 2 Installation 2.3 Jumper Location The following picture shows the silk plot of the starter-kit with marked default jumper settings. Figure 2-1: Default Jumper Settings FMEMCU-UG-910074-11 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Software Installation
Chapter 2 Installation 2.4 Software Installation 2.4.1 Installation of Softune Workbench With the “SK-91460T-144PMC-GPIO” Fujitsu supplies a full working development environment called Softune Workbench V6. To develop own software the Softune Workbench development environment must be installed first. Follow the instructions for successful installation of the Softune Workbench. -
Page 14: Jumpers And Switches
0 (low) ON (closed) 1 (high) S1/3 (MD2) OFF (open) 0 (low) S1/4 Table 3-1: MCU Operating Mode MD0 MD1 MD2 NC DIP-Switch S1 (default setting) Figure 3-1: MCU mode switch FMEMCU-UG-910074-11 - 14 - © Fujitsu Microelectronics Europe GmbH... -
Page 15: Power Supply (S3, Jp: 8, 9, 11, 12, 66)
S3 switches the Board on and off Table 3-3: Power Supply Configuration By default, I/O supply and MCU Core are set to 5V and the external bus I/F is set to 3.3 V. © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-910074-11... - Page 16 SK-91460T-144PMC-GPIO User Guide Chapter 3 Jumpers and Switches Figure 3-2: Voltage Test Pins Regulator Test Pin Voltage 5.0 V 3.3 V Table 3-4: Voltage Test Pins FMEMCU-UG-910074-11 - 16 - © Fujitsu Microelectronics Europe GmbH...
-
Page 17: Analog Power Supply Voltage (Jp: 3, 5, 7)
If JP3 and JP7 are open, the user has to supply an adequate analog voltage supply (AVcc and AVss) to the A/D-converter. If JP5 is open, the resistors R4 and R6 define AVRH. By default the resistor network (R4, R6) is not mounted on the board. © Fujitsu Microelectronics Europe GmbH - 17 - FMEMCU-UG-910074-11... -
Page 18: Lin / Uart Connectors (X2 - X5)
Pin 1 (LIN Vs) of X2 is not connected to Vin Table 3-6: UART 4 Settings By default, UART4 is connected to X2 and configured as RS232 interface. For Flash programming, UART4 has to be used (RS232). FMEMCU-UG-910074-11 - 18 - © Fujitsu Microelectronics Europe GmbH... - Page 19 (LIN Vbat) Open Pin 1 (LIN Vs) of X3 is not connected to Vin Table 3-7: UART 5 Settings By default, UART5 is connected to X3 and configured as RS232 interface. © Fujitsu Microelectronics Europe GmbH - 19 - FMEMCU-UG-910074-11...
- Page 20 (LIN Vbat) Open Pin 1 (LIN Vs) of X4 is not connected to Vin Table 3-8: UART 6 Settings By default, UART6 is connected to X4 and configured as RS232 interface. FMEMCU-UG-910074-11 - 20 - © Fujitsu Microelectronics Europe GmbH...
- Page 21 (LIN Vbat) Open Pin 1 (LIN Vs) of X5 is not connected to Vin Table 3-9: UART 7 Settings By default, UART7 is connected to X5 and configured as RS232 interface. © Fujitsu Microelectronics Europe GmbH - 21 - FMEMCU-UG-910074-11...
-
Page 22: Can Interfaces (X7-X8)
This solder jumper selects the third voltage monitored by the reset IC (5V and JP32 3.3V are always monitored). Open this jumper if no external Reset shall be generated. JP38 In this case only the internal reset is active (e.g.: power-on) FMEMCU-UG-910074-11 - 22 - © Fujitsu Microelectronics Europe GmbH... - Page 23 If JP13 (DTR/DTRx) is set, one of the RST jumpers (JP15, 16, 42, 43) and the according DTR/RTS jumper have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-910074-11...
-
Page 24: User Buttons Sw1, Sw2, Sw3, Sw4, Sw5 (Jp: 1, 2, 4, 6, 14)
JP41. The voltage to this pin can be adjusted with RP2 and measured at J17. Jumper Setting Description JP41 closed RP2 is connected to AN6 Table 3-13: Potentiometer Settings FMEMCU-UG-910074-11 - 24 - © Fujitsu Microelectronics Europe GmbH... -
Page 25: Connectors
37 – 72 73 – 108 109 – 144 The odd pin numbers are located on the one side and the even pin numbers are located on the other side of the connector. © Fujitsu Microelectronics Europe GmbH - 25 - FMEMCU-UG-910074-11... -
Page 26: Lin-Uart Connectors (X2-X5)
Description Not used CANL LOW-level CAN voltage input/output Ground Not used Not used Not used CANH HIGH-level CAN voltage input/output Not used Not used Shield Ground Table 4-2: CAN Connector Signals FMEMCU-UG-910074-11 - 26 - © Fujitsu Microelectronics Europe GmbH... -
Page 27: User-Leds & Optional Lc-Display
The following control signals are provided: Pins for LCD-backligh Figure 4-4: User LEDs/LCD LED- LED+ 16_5 16_4 16_3 16_2 15_2 15_1 15_0 Port Table 4-3: User LEDs/LCD (Optional Pins: Pin15: Vcc via 39Ω/0.5W, Pin16: GND) © Fujitsu Microelectronics Europe GmbH - 27 - FMEMCU-UG-910074-11... -
Page 28: In-Circuit-Programming Connector (X1)
Not used Not used Not used Not used INITX MCU reset signal SIN4 UART4 receive data SOT4 UART4 transmit data SCK4 UART4 clock Board supply voltage Ground Table 4-4: In-circuit programming connector FMEMCU-UG-910074-11 - 28 - © Fujitsu Microelectronics Europe GmbH... -
Page 29: Getting Started
A double-click on one of the files will invoke the built-in editor, which supports syntax-highlighting, tags and various other functions. Figure 5-1: Softune Workbench main window Note: You may customize the editor by a right-click on the editor window. © Fujitsu Microelectronics Europe GmbH - 29 - FMEMCU-UG-910074-11... - Page 30 F1. In many cases, you can get some useful hints how to solve the problem. Of course, you can also use the HELP-menu anytime during development or debugging. FMEMCU-UG-910074-11 - 30 - © Fujitsu Microelectronics Europe GmbH...
-
Page 31: Project Start-Up
Chapter 5 Getting Started 5.2 Project Start-up In order to allow a quick and smooth project start-up Fujitsu Microelectronics Europe supplies a template project as a reference. The easiest way to start a new project is to make a copy of the template project and use this copy as a start-up. The template includes the latest start91460.asm file, MCU header file, IRQ table, basic linker and C-Compiler settings. - Page 32 SK-91460T-144PMC-GPIO User Guide Chapter 5 Getting Started 91460_template_91467t Rename “ ” into “my_application” 6. Start Softune Workbench and open your project Figure 5-2: Open Softune Workbench workspace (*.wsp) FMEMCU-UG-910074-11 - 32 - © Fujitsu Microelectronics Europe GmbH...
-
Page 33: Softune Workbench Debugger
Explanations in this manual refer to the SWB Monitor Debugger only. For further information please see also the application note “SWB_monitor_debugger” The Starterkit SK-91460T-144PMC-GPIO does NOT support debugging with Monitor debugger. The emulator debugger: The in-circuit emulator (ICE) is a system, which allows a connection to any target system using a probe-cable. - Page 34 “Project – Setup Project – Debug” menu. The current selection is blue marked (icon): 5.1.2 Starterkit SW-example The SK-91460T-144PMC-GPIO is delivered with a SW-Application which allows the testing of different functionalities. Run Skwizard.bat, select 19200 baud. Connect UART4 (X2) of starterkit to the PC (e.g.
-
Page 35: Programming The Internal Flash
SIN4 is connected to RS232 transceiver (RXD) JP25 SOT4 is connected to RS232 transceiver (TXD) JP27 X2 Pin2 is connected to RS232 transceiver (T1out) (RS232/LIN) Table 6-1: Jumper Settings for Programming © Fujitsu Microelectronics Europe GmbH - 35 - FMEMCU-UG-910074-11... - Page 36 5) Choose the microcontroller device (“MB91F467T”) as device type and browse to the mhx-file you want to program to the embedded flash memory of the microcontroller. Press the button “Automatic Mode” to start programming. 6) After that, immediately reset the microcontroller. FMEMCU-UG-910074-11 - 36 - © Fujitsu Microelectronics Europe GmbH...
- Page 37 MCU manually immediately after pressing the button “Automatic Mode”. Figure 6-2: Reset Signal Settings © Fujitsu Microelectronics Europe GmbH - 37 - FMEMCU-UG-910074-11...
-
Page 38: Synchronous Mode
A dedicated Flash programming socket (X1) is provided on the evaluation-board for direct connection to this programmer. n/c 1 2 n/c n/c 3 4 n/c RST 5 6 SIN4 SOT4 7 8 SCK4 VCC 9 10 GND Figure 6-4: X1 Flash Programming Socket FMEMCU-UG-910074-11 - 38 - © Fujitsu Microelectronics Europe GmbH... -
Page 39: Troubleshooting
Optional LC-Display at J1 does not work ∗ Adjust the potentiometer RP1 to adjust contrast of LCD. Remove resistor network RN1. Graphic sub-board does not work Check power supply 9-12V/1500mA. Reduce external bus clock frequency. © Fujitsu Microelectronics Europe GmbH - 39 - FMEMCU-UG-910074-11... -
Page 40: Appendix
< MB2198-10 DSU cable EMA-MB91V460A-002B-80 Adapter board < NQPACK144SD-ND Socket for package FPT-176P-M07 (Tokyo Eletech Corp) http://www.tetc.co.jp/e_products/e_nq_techdrawings.htm < EMA-MB91F467T-NLS-144M08 Emulator probe cable MB91F467TA EMA-MB91F467T-LS-144M08 < MB91460 Series < MB91F467TA-144PMC Flash MCU FMEMCU-UG-910074-11 - 40 - © Fujitsu Microelectronics Europe GmbH... -
Page 41: Information In The Www
SK-91460T-144PMC-GPIO User Guide Chapter 8 Appendix 8.2 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/... -
Page 42: Tables
Table 4-2: CAN Connector Signals ..................26 Table 4-3: User LEDs/LCD....................27 Table 4-4: In-circuit programming connector ................ 28 Table 6-1: Jumper Settings for Programming............... 35 Table 6-2: Jumper Settings for reset signal ................36 FMEMCU-UG-910074-11 - 42 - © Fujitsu Microelectronics Europe GmbH... -
Page 43: Figures
Figure 5-3 Skwizard after reset of starterkit................34 Figure 6-1: Settings for Automatic Mode ................37 Figure 6-2: Reset Signal Settings..................37 Figure 6-3: Successful Programming in Automatic Mode ............. 38 Figure 6-4: X1 Flash Programming Socket................38 © Fujitsu Microelectronics Europe GmbH - 43 - FMEMCU-UG-910074-11... -
Page 44: Abbreviations
8.5 Abbreviations Analogue Digital Converter Controller Area Network Chip Select Fujitsu Microelectronics Europe GmbH Local Interconnect Network Microcontroller Unit Printed Circuit Board SRAM Static Random Access Memory UART Universal Asynchronous Receiver Transmitter FMEMCU-UG-910074-11 - 44 - © Fujitsu Microelectronics Europe GmbH... -
Page 45: China-Rohs Regulation
“Year”. © Fujitsu Microelectronics Europe GmbH - 45 - FMEMCU-UG-910074-11... - Page 46 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication FMEMCU-UG-910074-11 - 46 - © Fujitsu Microelectronics Europe GmbH...
-
Page 47: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen © Fujitsu Microelectronics Europe GmbH - 47 - FMEMCU-UG-910074-11...