Related Manuals for Fujitsu MB91470 SERIES
Summary of Contents for Fujitsu MB91470 SERIES
-
Page 1: Evaluation Board
Fujitsu Microelectronics Europe FMEMCU-UG-910067-10 User Guide FR FAMILY MB91470 SERIES EVALUATION BOARD SK-91470-144PMC1-MC USER GUIDE... -
Page 2: Revision History
SK-91470-144PMC1-MC User Guide Revision History Revision History Date Issue 2007/11/19 V1.0 Cha First Version This document contains 24 pages. FMEMCU-UG-910067-10 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer’s use or the transport. -
Page 4: Table Of Contents
PWM LEDs......................19 MotorDrive connector....................20 Hall sensor and encoder interface (JP: 20, 21, 22, 29, 31, 33, 34)......21 7 RELATED PRODUCTS ....................22 8 INFORMATION IN THE WWW ..................23 FMEMCU-UG-910067-10 - 4 - © Fujitsu Microelectronics Europe GmbH... -
Page 5: Overview
1.2 Features - Supports Fujitsu’s MB91470 Series MCUs in the FPT-144P-M12 package or the MB91FV470 evaluation MCU with the MB2198-160 adapter board and the MB2198-161 header board. By default, the Board is delivered with an MB91F479-PMC1 MCU. -
Page 6: General Description
The analog inputs of the 12-bit AD converter units 3+4 as well as AN2-0 to AN2-7 of the 10- bit ADC unit 2 can be equipped with a capacitor in order to reduce noise by forming an RC low-pass with an external or on-board resistor. FMEMCU-UG-910067-10 - 6 - © Fujitsu Microelectronics Europe GmbH... -
Page 7: Installation
Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems, please loosen the screws and tighten the screws again equally. Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will contaminate inside of connector. © Fujitsu Microelectronics Europe GmbH - 7 - FMEMCU-UG-910067-10... -
Page 8: Default Jumper Settings
OPT6 – AN2-4 open Jumper 2pin JP40 PWMLEDS closed Jumper 3pin JP41 DCIN INT/EXT Jumper 3pin JP42 I Phase B ADC select Jumper 2pin JP43 U DC Bus sense – AN2-3 closed FMEMCU-UG-910067-10 - 8 - © Fujitsu Microelectronics Europe GmbH... - Page 9 OPT1_LED Jumper 2pin open JP46 U Phase A sense – AN2-0 Jumper 2pin open JP47 U Phase B sense – AN2-1 Jumper 2pin open JP48 U Phase C sense – AN2-2 © Fujitsu Microelectronics Europe GmbH - 9 - FMEMCU-UG-910067-10...
- Page 10 SK-91470-144PMC1-MC User Guide Chapter 3 Default Jumper settings UART2 UART1 UART0 FMEMCU-UG-910067-10 - 10 - © Fujitsu Microelectronics Europe GmbH...
-
Page 11: Jumpers And Switches
Selects on-board (X15) or ext. (X12) DC input Jumper Setting Description JP26 Closed MCUVCC connected to VCC5 (MCUVCC) Open for current measurement JP41 DC input by X15 (DCIN EXT/INT) DC input by X12 (ext. power stage) © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-910067-10... -
Page 12: Analog Power Supply Voltage (Jp: 24, 27, 28, 35, 36)
If JP28 is open, the resistors R26 and R36 define AVRH3. If JP36 is open, the resistors R43 and R47 define AVRH4. By default the resistor networks are not mounted on the board. Standard SMD0805 chip resistors can be used. FMEMCU-UG-910067-10 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Uart0 (Jp: 2, 3, 4)
SOT1 not connected to UART1 Open Closed RTS and CTS of X6 are connected JP15 (RTS-CTS) Open RTS and CTS of X6 are not connected By default, UART1 (SIN1/SOT1) is connected to X6. © Fujitsu Microelectronics Europe GmbH - 13 - FMEMCU-UG-910067-10... -
Page 14: Uart2 (Jp: 17, 18, 19)
MCU Pin 17 (PJ7/TOUT3) not connected to U5 Closed INITX connected to reset circuit / supply monitor U5 JP25 (Ext. Reset) Open No connections to INITX JP30 Closed U5 watchdog function enabled (Watchdog) Open U5 watchdog function disabled FMEMCU-UG-910067-10 - 14 - © Fujitsu Microelectronics Europe GmbH... -
Page 15: Buttons Sw1-Sw7 (Jp: 1, 5, 6, 8, 10, 11, 25, 38)
INITX is connected to the reset IC and SW7 JP25 (Reset) Open No connection to INITX By default, all push-buttons as well as the reset circuit are connected to the microcontroller. © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-910067-10... -
Page 16: Programming The Internal Flash Memory
In case of errors, please check COM-Port configuration, cable connection and jumper settings. 9. After successful programming, Power off the board and set JP32 back to 1-2 (RUN) 10. Power on the board to start the application FMEMCU-UG-910067-10 - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Synchronous Mode
VCC 9 10 GND To allow the parallel programming tool to set the mode pins and programming mode (P80/P81), be sure to remove JP32 and external circuits connected to P80/P81 (Pin 20+21). © Fujitsu Microelectronics Europe GmbH - 17 - FMEMCU-UG-910067-10... -
Page 18: Connectors
TXD is the transmit output, RXD is the receive input. The DTR signal can be used to generate a reset. Please use a 1:1 cable for PC connection. Connectors X5-X7: CTS RTS DSR FMEMCU-UG-910067-10 - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: User-Leds & Optional Lc-Display
LED18 can be connected to P87/INT7/PPG7 (Pin27) in order to indicate the brake chopper control signal (JP37 set). The solder JP45 can be opened to disable the LED also when JP37 is set, in case this is needed. © Fujitsu Microelectronics Europe GmbH - 19 - FMEMCU-UG-910067-10... -
Page 20: Motordrive Connector
(INT7/PPG7) in case the external circuit provides e.g. a break resistor which shall be controlled by PPG7 or an additional interrupt source to be monitored. JP39 connects OPT6 to the analog input AN2-4 (Pin86), e.g. for a temperature sensor. FMEMCU-UG-910067-10 - 20 - © Fujitsu Microelectronics Europe GmbH... -
Page 21: Hall Sensor And Encoder Interface (Jp: 20, 21, 22, 29, 31, 33, 34)
AIN0 and TIN0 are connected If required by the encoder in use, additional pull-up resistors (R28-R30, usually 2k7) can be mounted on the board near the encoder connector. Use standard SMD0805 chip resistors. © Fujitsu Microelectronics Europe GmbH - 21 - FMEMCU-UG-910067-10... -
Page 22: Related Products
SK-91470-144PMC1-MC User Guide Chapter 7 Related Products 7 Related Products < SK-91470-144PMC1-MC Evaluation board for the MB91470 Series MCU in the FPT-144P-M12 package < SK-91F479-144PMC1-MC Evaluation board with MB91F479 Series MCU in the FPT-144P-M12 package (no MCU socket) < SK-POWER-3P-LV-MC... -
Page 23: Information In The Www
Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Linear Products: Power Management, A/D and D/A Converters http://www.fujitsu.com/emea/services/microelectronics/linears/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU MICROELECTRONICS http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-910067-10... - Page 24 According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen FMEMCU-UG-910067-10 - 24 - © Fujitsu Microelectronics Europe GmbH...