Advertisement
Quick Links
LED Light Kit
Groundsmaster
Series Traction Unit
Model No. 31696
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
Note:
Retain all removed parts for later installation
unless otherwise noted.
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface.
2.
Engage the parking brake.
3.
Lower the cutting unit.
4.
Shut off the engine and remove the key.
5.
Wait for all moving parts to stop.
6.
Allow the engine to cool completely.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3500 Series Rotary Mower or Reelmaster
Description
No parts required
Switch assembly
Light bracket
Carriage bolt (5/16 x 3/4 inches)
Nut (5/16 inch)
Light assembly
Hex-head flange bolt (5/16 x 3/4 inches)
Wire harness (black and blue light
connectors)
Wire harness 15.2 cm (6 inch)
Register at www.Toro.com.
Qty.
–
Prepare the machine.
1
Install the switch.
1
4
4
Install the light assemblies.
2
2
1
Install the wire harnesses.
1
2
Installing the Switch
Parts needed for this procedure:
1
Switch assembly
Procedure
1.
Remove the cover from the battery box
1).
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3441-121 Rev B
®
3100-D
Installation Instructions
Use
(Figure
*3441-121*
Advertisement
Related Manuals for Toro 31696
Summary of Contents for Toro 31696
- Page 1 Form No. 3441-121 Rev B LED Light Kit Groundsmaster ® 3500 Series Rotary Mower or Reelmaster ® 3100-D Series Traction Unit Model No. 31696 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
- Page 2 Disconnect the negative (-) battery cable from the battery (Figure Remove the 2 screws securing the console shroud and remove the shroud (Figure g312596 Figure 1 1. Battery box cover 2. Negative (-) battery cable g312597 Figure 2 1. Console shroud WARNING Using the dimensions shown in Figure...
- Page 3 Mount the switch to control panel with the hex nuts and lock washer (Figure Note: The key way slot in the switch mounting threads indicates the O position. g312595 Figure 4 1. Switch...
- Page 4 Installing the Light Assemblies Parts needed for this procedure: Light bracket Carriage bolt (5/16 x 3/4 inches) Nut (5/16 inch) Light assembly Hex-head flange bolt (5/16 x 3/4 inches) Procedure Using the dimensions shown in Figure 5, locate, mark, and drill 2 holes (10 mm (3/8 inch)) through the operator floor plate.
- Page 5 Using the drilled holes, mount the light bracket to Mount the 2 lights to the bracket with 2 carriage the underside of the floor plate with 2 hex-head bolts (5/16 x 3/4 inches) and 2 locknuts (5/16 flange bolts (5/16 x 3/4 inches) and 2 locknuts inch);...
- Page 6 • Connect the blue wired ring terminal to the center bottom terminal of the switch with the washer and screw (.Figure • Connect the white wired ring terminal to the remaining terminal of the switch with the washer and screw (Figure g316463 Figure 7...
- Page 7 Switch the lights on. Aim the lights as desired and tighten mounting nuts. g312759 Figure 8 1. Fuse Install the control panel shroud. Remove and discard the existing negative (-) battery cable clamp bolt (Figure g312760 Figure 9 1. Negative (-) battery cable Loosely install the new battery clamp bolt/ground stud (Figure...