Advertisement
Quick Links
CE Guard Kit
Groundsmaster
Model No. 31204
Determine the left and right sides of the machine from the normal operating position.
Safety
This product contains a chemical or chemicals known to the State of California to
CAUTION
This machine produces sound levels in excess of 85
dBA at the operator's ear and can cause hearing loss
through extended periods of exposure.
Wear hearing protection when operating this
machine.
Sound Power Level
This unit has a guaranteed sound power level of 105 dBA,
which includes an Uncertainty Value (K) of 1 dBA.
Sound power level was determined according to the
procedures outlined in ISO 11094.
Sound Pressure Level
This unit has a sound pressure level at the operator's ear of
90 dBA, which includes and Uncertainty Value (K) of 1 dBA.
Sound pressure level was determined according to the
procedures outlined in EN ISO 5395:2013.
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3280-D Traction Unit
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Register at www.Toro.com.
Vibration Level
Hand-Arm
Measured vibration level for right hand = 1.25 m/s
Measured vibration level for left hand = 1.28 m/s
Uncertainty Value (K) = 0.5 m/s
Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.
Whole Body
Measured vibration level = 0.37 m/s
Uncertainty Value (K) = 0.5 m/s
Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.
Original Instructions (EN)
All Rights Reserved *3405-205* B
Printed in the USA
Form No. 3405-205 Rev B
Installation Instructions
2
.
2
.
2
.
2
.
2
.
Advertisement
Related Manuals for Toro 31204
Summary of Contents for Toro 31204
- Page 1 Form No. 3405-205 Rev B CE Guard Kit Groundsmaster ® 3280-D Traction Unit Model No. 31204 Installation Instructions Determine the left and right sides of the machine from the normal operating position. Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 120-6563 1. Lock 2. Unlock 131-3393 133-6387 1. Read the Operator's Manual. 1. - Page 3 133-6376 (Apply over 133-6375 for CE machines) * This safety decal includes a slope warning required on the machine for compliance to the European Lawn Mower Safety Standard EN ISO 5395:2013. The conservative maximum slope angles indicated for operation of this machine are prescribed by and required by this standard. 1.
- Page 4 Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Guard mount Gearbox guard Joint guard Drive-assembly guard Nut (1/4 inch) Shoulder bolt Install the gearbox guards. Spring washer Spacer Washer (9/32 inch) Bolt (1/4 x 5/8 inch) Bolt (3/8 x 1/2 inch) Bolt (1/4 x 3/8 inch)
- Page 5 Installing the Gearbox Guards Parts needed for this procedure: Guard mount Figure 2 Gearbox guard 1. Fuel-tank support bracket 3. Bolt (1/4 x 3/8 inch) Joint guard 2. Guard mount Drive-assembly guard Nut (1/4 inch) 4. Attach the joint guard to the drive-assembly guard Shoulder bolt using a bolt (1/4 x 5/8 inch), spacer, washer (9/32 inch), and nut (1/4 inch) as shown in...
- Page 6 5. Attach the joint guard to the gearbox guard using 2 shoulder bolts, 2 spring washers, and 2 nuts (1/4 inch) as shown in Figure Installing the PTO Guards Parts needed for this procedure: Left PTO guard Right PTO guard Grommet Bolt (3/8 x 7/8 inch) Washer (7/16 inch)
- Page 7 1. If you have a 4-wheel-drive model, insert the grommet 5. Attach the front of the left PTO guard to the left side of into the right PTO guard (Figure the machine using 2 bolts (5/16 x 3/4 inch), 2 washers (3/8 inch), and 2 nuts (5/16 inch) as shown in Figure Figure 7...
- Page 8 8. Use the table below to select the correct tipping-hazard-warning decal for your machine from decal 133-6387. Model 30366 Model Model 30403 Model 30551 Model 30404 Model 31335 Model 31336 30366+30348 60-inch base deck 62-inch base 62-inch SDD 72-inch base 72-inch 72-inch SDD deck...
- Page 9 1. Select the axle guard for either the 2-wheel-drive or 4-wheel-drive machine (Figure 13). 2. Remove the existing bolt from the machine (Figure 13). Note: Right bolt on the 2-wheel drive axle guard and Installing the Hood Latch left bolt on the 4-wheel drive axle guard. Parts needed for this procedure: Lock assembly Hood latch...
- Page 10 4. Insert the lock assembly and washer into the hole on the hood and secure it underneath with the nut (Figure 15). Note: Ensure that the lock is correctly oriented. Installing the Lift-Lock Lever Parts needed for this procedure: Lift-lock lever Flat washer Spring washer Spacer...
- Page 11 Figure 17 1. Screw 5. Flat washer 2. Lift-lock lever 6. Decal 3. Spring washer 7. Locknut 4. Spacer 4. Insert the lift-lock lever assembly screw into the control-panel hole and secure it with a locknut. Position the lift-lock lever as shown in Figure 5.