Advertisement
Quick Links
Seat Kit
Groundsmaster
Model No. 32301
Model No. 32302
Model No. 32303
Installation
1
Preparing the Machine
No Parts Required
Procedure
•
Groundsmaster 3200 or 3300 machines: Perform the following steps:
1.
Park the machine on a level surface.
2.
Engage the parking brake.
3.
Lower the cutting unit.
4.
Shut off the engine and remove the key.
5.
Disconnect the battery; refer to the electrical system maintenance section of your Operator's Manual.
•
Groundsmaster e3200 or e3300 machines: Perform the following steps:
1.
Park the machine on a level surface.
2.
Ensure that the parking brake is engaged; refer to your traction unit Operator's Manual.
3.
Lower the cutting unit.
4.
Shut off the machine and remove the key.
5.
Turn the battery-disconnect switch to the O
© 2024—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
e3200, e3300, 3200, or 3300 Series Traction Unit
position.
FF
Register at www.Toro.com.
Form No. 3468-241 Rev A
Installation Instructions
*3468-241*
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Related Manuals for Toro 32301
Summary of Contents for Toro 32301
- Page 1 Form No. 3468-241 Rev A Seat Kit Groundsmaster ® e3200, e3300, 3200, or 3300 Series Traction Unit Model No. 32301 Model No. 32302 Model No. 32303 Installation Instructions Installation Preparing the Machine No Parts Required Procedure • Groundsmaster 3200 or 3300 machines: Perform the following steps: Park the machine on a level surface.
- Page 2 Remove the console from the seat base (Figure 2) and retain the nuts. Important: Support the console after removing it so that it does not crimp or hang Installing the Seat to the by the cables and wires. Traction Unit Parts needed for this procedure: Bolt Plate...
- Page 3 2. Seat base Routing the Wire Harness g299316 Note: Figure 4 Models 32301 and 32302 are equipped with 1 wire harness (i.e., the seat-switch wire harness). 1. Seat 2. Seat base Model 32303 is equipped with 2 wire harnesses (i.e., the seat-switch wire harness and the air-ride-seat wire harness).
- Page 4 Machine Label—seat-switch Label—machine wire harness wire harness P02 (SEAT NO) P11 (SEAT SWITCH) Groundsmaster 3200/3300 P03 (SEAT NC) Not applicable for these machines. P02 (SEAT NO) P79 (SEAT SWITCH Groundsmaster e3200/e3300 P03 (SEAT NC) P96 (SEAT SWITCH • Installing the Air-Ride-Seat Wire Harness (Model 32303 only): Install the end of the air-ride-seat wire harness to the machine wire-harness connector shown in the...
- Page 5 g490183 Figure 10 Groundmaster e3200/e3300 machine shown 1. Nuts Use the retained bolts to install the seat-base plates to each side of the seat base (Figure 1 Figure Position the console to the seat bracket (A in Figure 11). For Model 31900, 31901, 31907, and 31909 machines: Ensure that the throttle cable is g490184 Figure 9...
-
Page 6: Completing The Installation
Tighten the carriage bolt and nut, then tighten the existing nuts to the console studs. Secure the plate to the seat bracket with 3 carriage bolts and 3 nuts (B in Figure 11). Completing the Installation No Parts Required Procedure Perform the following steps for your machine: •... -
Page 7: Product Overview
Use the fore/aft adjustment lever to change the forward/rearward position of the seat. • Model 32301: Move the lever to the left (Figure 12), move the seat to a comfortable position, and release the locking lever to secure the position of the seat.