Advertisement
Quick Links
Baffle Kit
72in Rear Discharge Z Master
Model No. 144-0380
Important:
This kit does not come with the recycler blades.
1
Preparing the Machine
No Parts Required
Procedure
1.
Disengage the PTO, move the motion-control
levers to the N
EUTRAL
engage the parking brake.
2.
Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.
3.
Raise the front of the machine and support it
with jack stands.
WARNING
Raising the mower deck for service
or maintenance relying solely on
mechanical or hydraulic jacks could be
dangerous. The mechanical or hydraulic
jacks may not be enough support or may
malfunction, allowing the unit to fall,
which could cause injury.
Do not rely solely on mechanical
or hydraulic jacks for support. Use
adequate jack stands or equivalent
support.
4.
Repair all bent or damaged areas of mower
deck and replace any missing parts.
5.
Clean the machine of any debris on the deck to
ease installation.
6.
Remove the existing blades; refer to the
Operator's Manual.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
-
position, and
LOCK
Register at www.Toro.com.
®
Mowers
7.
Remove the 4 hex-socket screws (5/16 x 3/4
inch) and 4 flange nuts (5/16 inch) plugging the
exposed mounting holes in the deck and the
inboard tire flap fastener on each side
Note:
Retain these parts for future use.
Figure 1
1. Socket screw
8.
Remove and retain the 2 rear carriage bolts (3/8
x 2-1/4 inches) and 2 flange nuts (3/8 inch) from
each side within the cutting chamber securing
the side bumpers to the deck sides.
Original Instructions (EN)
All Rights Reserved *3438-988* A
Printed in the USA
Form No. 3438-988 Rev A
Installation Instructions
(Figure
2. Carriage bolt
1).
g024566
Advertisement
Related Manuals for Toro 144-0380
Summary of Contents for Toro 144-0380
- Page 1 Form No. 3438-988 Rev A Baffle Kit 72in Rear Discharge Z Master ® Mowers Model No. 144-0380 Installation Instructions Important: This kit does not come with the recycler blades. Remove the 4 hex-socket screws (5/16 x 3/4 inch) and 4 flange nuts (5/16 inch) plugging the...
- Page 2 Installing the Baffles Parts needed for this procedure: Front, right baffle Rear, right baffle Front, center baffle Rear, center baffle Front, left baffle Rear, left baffle Right kicker baffle Center kicker baffle Left kicker baffle Locknut (3/8 inch) Carriage bolt (3/8 x 7/8 inch) Flange nut (3/8 inch) Carriage bolt (5/16 x 1 inch) Flange nut (5/16 inch)
- Page 3 g024570 Figure 2 1. Front, right baffle 8. Left kicker baffle 2. Carriage bolt 9. Rear, left baffle 3. Flange nut 10. Locknut 4. Center kicker baffle 11. Rear, center baffle 5. Front, center baffle 12. Rear, right baffle 6. Front, left baffle 13.
- Page 4 Install the rear, center baffle using 2 carriage Tighten all the hardware. bolts (3/8 x 7/8 inch) and 2 locknuts (3/8 inch) Install the correct kicker baffle to each chamber as shown in Figure using 1 carriage bolt (3/8 x 7/8 inch) and 1 flange nut (3/8 inch) as shown in Figure Note:...
- Page 5 Securing the Bumpers and Converting Back to Rear Right and Left Baffle to the Discharge Mower Deck No Parts Required Parts needed for this procedure: Procedure Carriage bolt (3/8 x 2-1/2 inches) Disengage the PTO, move the motion-control Flange nut (3/8 inch) levers to the N position, and EUTRAL...
- Page 6 Notes:...
- Page 7 Notes:...