Advertisement
Quick Links
Tri-Roller
for Greensmaster
Model No. 04722—Serial No. 400000000 and Up
Setup
1
Installing the Tri-Roller
Units
No Parts Required
Procedure
1.
Park the machine on a level surface, shut off the
engine, engage the parking brake, and remove
the key.
2.
Position the tri-roller unit under the suspension
arm.
3.
With the latches on the suspension-arm bar
pointing up
(Figure
down so that the bar fits over the bar across the
top of the tri-roller unit
1. Latch—closed position
2. Suspension-arm bar
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
1), push the suspension arm
(Figure
2).
Figure 1
3. Latch—open position
Register at www.Toro.com.
3300/3400 Series TriFlex
1. Suspension-arm bar
4.
Close the latches down and around the tri-roller
unit and lock them in place
Note:
latches are properly locked in place.
5.
Insert the motor into the left side of the tri-roller
unit (as viewed from the operator's position) and
pull the motor retaining bar on the tri-roller unit
toward the motor until you hear a "click" from
both sides of the motor
g018311
Form No. 3409-884 Rev B
®
Traction Units
Operator's Manual
Figure 2
2. Tri-roller unit bar
(Figure
You will hear and feel a "click" when the
(Figure
Original Instructions (EN)
All Rights Reserved *3409-884* B
Printed in the USA
g018312
1).
3).
Advertisement
Related Manuals for Toro 04722
Summary of Contents for Toro 04722
- Page 1 Form No. 3409-884 Rev B Tri-Roller for Greensmaster ® 3300/3400 Series TriFlex ® Traction Units Model No. 04722—Serial No. 400000000 and Up Operator's Manual Setup Installing the Tri-Roller Units No Parts Required Procedure g018312 Figure 2 Park the machine on a level surface, shut off the engine, engage the parking brake, and remove 1.
- Page 2 Removing the Tri-Roller Unit No Parts Required Procedure Park the machine on a clean level surface, lower the tri-roller units to the ground until the suspension hydraulics are fully extended, shut off the engine, engage the parking brake, and remove the key from the ignition switch. Push the motor retaining bar out of the slots on the motor toward the tri-roller unit and remove the motor from the tri-roller unit.
-
Page 3: Operation
Install 4 spacers (1/8 inch) per bolt between protruding objects. the counterweight and the tri-roller side plate (Figure Note: These spacers are not included with this kit. Toro part number: 63-8410. Install the hybrid auxiliary weight provided with the traction unit with the provided bolts. -
Page 4: Maintenance
Maintenance Lubricating the Tri-Roller Lubricate the 2 grease fittings (Figure 6) on each tri-roller unit after every 15 hours of operation, with No. 2 lithium grease. Use a hand-operated grease gun for best results. Wipe each grease fitting with a clean rag. Apply grease to the tri-roller shaft bearings until you feel pressure (Figure... - Page 5 Notes:...
- Page 6 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 7 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.