Page 1 User’s Manual TECRA S3...
Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA S3 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 3 EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
Page 4 Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Page 5: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 6 General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system.
Page 7: Table Of Contents
Table of Contents General Precautions Preface Introduction Chapter 1 Equipment checklist........1-1 Features.
Page 8 Replacing the battery pack ....... . .6-12 TOSHIBA Password Utility ....... . .6-13 Power-up modes .
Page 9 TOSHIBA support ........
Page 10 Regulatory statements........E-3 Using Bluetooth™ Card from TOSHIBA equipment in Japan ..E-6 Approved Countries/Regions for use (Bluetooth™...
Page 11: Preface
This manual tells how to set up and begin using your TECRA S3 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 12 Preface Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available.
Page 13 Preface Display Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention.
Page 14 Preface User’s Manual...
Page 15: Equipment Checklist
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 16: Features
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
Page 17 (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration.
Page 18 Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 19 Introduction Disks Hard disk drive Available in four sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) Part of the space on the hard disk drive is reserved as administration space.
Page 20: Optical Media Drive
Introduction Optical media drive Computers in this series can be configured with an optical media drive installed in the Ultra Slim Bay. The available optical media drives are described below. DVD-ROM&CD-R/RW Some models are equipped with a full-size, drive DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor.
Page 21 Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 15" TFT LCD screen, 16 M colors, with one of the following resolutions: ■...
Page 22: Toshiba Dual Pointing Device
Introduction TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Built-in AccuPoint This pointer control stick, located in the center of the keyboard, provides convenient control of the cursor.
Page 23 Introduction Multimedia Sound system The Windows sound system compatible sound system provides internal speakers and a microphone as well as jacks for an external microphone and headphones. Video-out jack The video out jack lets you transfer video data to (S-Video) external devices.
Page 24 Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G).
Page 25: Special Features
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist Press this button to launch an application button automatically.
Page 26 Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. System automatic...
Page 27 Hibernation and shuts down. You can specify the setting in the Setup Actions tab in TOSHIBA Power Saver. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s...
Page 28: Utilities
Buttons: Assign applications or functions to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). 1-14 User’s Manual...
Page 29 Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD The TOSHIBA SD memory boot utility allows you Memory Boot Utility to create a bootable SD memory card to start the system. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows.
Page 30 Advanced Port Repricator III. To open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
Page 31 Introduction TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers. The...
Page 32: Options
A 256, 512 or 1,024 MB memory module (DDR2-533/400) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High capacity battery An additional battery pack can be purchased pack from your TOSHIBA dealer.
Page 33 Introduction USB floppy disk Kit The USB floppy disk drive accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte floppy disks through connection to a USB port. Please note that you cannot format 720-kilobyte floppy disks under Windows XP, but you are able to use disks that have been previously formatted.
Page 34 Introduction 1-20 User’s Manual...
Page 35: Chapter 2 The Grand Tour
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Disclaimer (Non-applicable Icons) Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis.
Page 36 The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
Page 37: Left Side
The Grand Tour Left side The following figure shows the computer’s left side. LAN active indicator ExpressCard eject button (orange) Cooling vents ExpressCard slot Video-out jack Link indicator (green) SD card slot LAN jack PC card eject button PC card slot External monitor port Security lock slot The left side of the computer...
Page 38 The Grand Tour External monitor This external monitor port lets you connect an port external video display. Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. ExpressCard slot The ExpressCard slot can accommodate an ExpressCard.
Page 39: Right Side
The Grand Tour Right side The following figure shows the computer’s right side. Ultra Slim Bay Modem jack USB ports Serial port The right side of the computer Universal Serial Bus Two Universal Serial Bus ports are on the (USB 2.0) ports right side.
Page 40: Back Side
The Grand Tour Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be installed in the Ultra Slim Bay. Serial port Use this 9-pin port to connect serial devices such as an external modem, serial mouse or serial printer.
Page 41: Underside
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Notches Battery lock Battery release Battery pack latch Ultra Slim Bay Docking port Memory module Ultra Slim cover Bay latch Hard disk drive...
Page 42 The Grand Tour Ultra Slim Bay See the Right side section in this chapter for details. Ultra Slim Bay latch Slide the latch to release or secure the Ultra Slim Bay ejector. Be sure to lock the Ultra Slim Bay latch before you transport or carry the computer.
Page 43: Front With The Display Open
Touch Pad control buttons Touch Pad LCD Sensor switch (Not shown) TOSHIBA Presentation button The front of the computer with the LCD panel open Display hinge The display hinge holds the LCD display panel at easy-to-view angles. Fingerprint Sensor...
Page 44: Accupoint Control
The Grand Tour Display screen The LCD screen displays high-contrast text and graphics. The available resolution depends on the model. With XGA, you can change the resolution between 800 × 600 and 1024 × 768 pixels. With SXGA, between 800 × 600 and 1400 ×...
Page 45 Hibernation Mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.
Page 46: System Indicators
The Grand Tour S y s t e m i n d i c a t o r s LEDs beneath icons, light when various computer operations are in progress. System indicators SD card The SD card indicator glows green when the computer is accessing the SD card slot.
Page 47: Keyboard Indicators
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 48: Usb Floppy Disk Drive (Optional)
The Grand Tour USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector into one of the USB ports of your computer.
Page 49: Optical Media Drives
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVD-ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives...
Page 50: Dvd Super Multi Drive
The Grand Tour Formats The drives support the following formats: ■ ■ CD-ROM DVD -Video ■ ■ DVD-ROM CD-Text ■ ■ CD-DA CD-ROM Mode 1, Mode 2 ■ ■ Photo CD™ Enhanced CD (CD-EXTRA) (single/multi-session) ■ Addressing Method 2 ■ CD-ROM XA Mode 2 (Form1, Form2) DVD-ROM&CD-R/RW drive...
Page 51: Ac Adaptor
For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.
Page 52 The Grand Tour 2-18 User’s Manual...
Page 53: Chapter 3 Getting Started
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 54: General Conditions
PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.
Page 55: Placement Of The Computer
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
Page 56: Seating And Posture
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Posture and positioning of the computer ■...
Page 57: Work Habits
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■...
Page 58: Connecting The Ac Adaptor
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety &...
Page 59 Getting Started ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 60: Opening The Display
Getting Started Connecting the power cord to the AC adaptor (3-pin plug) The Universal AC Adaptor and power cord bundled with this product may vary: depending on the model purchased, a 2-pin plug or 3-pin plug set (shown in the above figures) may be bundled. 2.
Page 61: Turning On The Power
Getting Started LCD display panel Display latch Opening the LCD display panel Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes.
Page 62: Starting Up For The First Time
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.
Page 63: Standby Mode
■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Page 64: Hibernation Mode
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 65: Starting Hibernation Mode
For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
Page 66: Restarting The Computer
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the displayed menu.
Page 67: Restoring Toshiba Utilities And Drivers
Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.
Page 68 Getting Started 3-16 User’s Manual...
Page 69: Chapter 4 Operating Basics
This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Page 70: Using The Accupoint
Operating Basics Two buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
Page 71: Using The Fingerprint Sensor
Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. A spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight Removing the AccuPoint cap 2.
Page 72: Points To Note About The Fingerprint Sensor
Operating Basics Points to note about the Fingerprint Sensor Due to the use of advanced technology to manufacture the fingerprint sensor, please abide by the following guidelines when using it. Please take extra care when handling the sensor surface. Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate.
Page 73 Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 74: Points To Note About The Fingerprint Utility
Operating Basics Align the finger and sensor as shown on the above figure. File/Folder Size Limitations. ■ When encrypting a file or folder using the Fingerprint recognition utility's file encryption function, note that encryption is not possible if the total file/folder size exceeds 2 GB or if the size of the encrypted file will exceed 2GB.
Page 75: Set Up Procedure
Operating Basics There is a section on Strong Logon Security in the help file, but the function is not available in the fingerprint utility provided in this computer. The sound during Log Off Current User (when logging off from OmniPass) cannot be set to off even if the No Audio Prompts configuration is set in Audio Settings.
Page 76: Windows Logon Via Fingerprint Authentication
Operating Basics 6. The Verify Fingerprint screen is displayed. Swipe the finger again to allow the sensor to read again. When the Verification Successful message is displayed, click Next. In case of finger injury or authentication failure, it is recommended that another fingerprint also be enrolled.
Page 77: Fingerprint System Boot Authentication
Operating Basics Fingerprint System Boot Authentication The fingerprint authentication system can be used to replace the keyboard-based User Password authentication system when booting. If you do not want to use the fingerprint authentication system for password authentication when booting, and prefer to use the keyboard-based system instead, press the BkSP (backspace) key when the Fingerprint System Boot Authentication screen is displayed.
Page 78: How To Enable Fingerprint System Boot Authentication
■ It is necessary to register the User Password before using the Fingerprint System Boot Authentication and its extended function, the Fingerprint Single Touch Boot Feature. Please use TOSHIBA Password Utility to register the User Password. ■ The Single Touch Boot Feature cannot function if Windows’s secure logon function (requiring users to press Ctrl + Alt + Del) is set to ON.
Page 79: Fingerprint Single Touch Boot Feature
TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 80: How To Swipe The Finger
Operating Basics How to Swipe the Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you.
Page 81: Using The Usb Floppy Disk Drive (Optional)
Operating Basics Using the USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. Connecting the USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into one of the computer’s USB ports.
Page 82: Changing Ultra Slim Bay Modules
DVD-ROM&CD-R/RW drive, DVD Super Multi drive and HDD adaptor. To avoid injury, do not put your hand into the Ultra Slim Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction, for information on using this utility to change modules while the computer’s power is on.
Page 83: Inserting A Module
Operating Basics Lock screw Ultra Slim Bay latch Optical media drive Removing the optical media drive Inserting a module Insert the Ultra Slim Bay HDD adaptor as described below. 1. Insert the Ultra Slim Bay HDD adaptor in the computer as shown below and press until the ejector clicks.
Page 84: Using Optical Media Drives
Operating Basics Using optical media drives The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows and the Ultra Slim Bay indicator glows.
Page 85 Operating Basics Disc tray Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray.
Page 86 Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Page 87: Removing Discs
Operating Basics Removing discs To remove the CD/DVD, follow the steps below. Do not press the eject button while the computer is accessing the media drive. Wait for the Ultra Slim Bay indicator to go out before you open the disc tray.
Page 88: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
Operating Basics How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Page 89: Before Writing Or Rewriting
RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 90: Writing Cd/Dvds On Dvd Super Multi Drive
Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■...
Page 91: Important Message
Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 92 Operating Basics DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2...
Page 93: When Writing Or Rewriting
Operating Basics ■ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data. ■...
Page 94 Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...
Page 95: Data Verification
3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).
Page 96: When Using Windvd Creator Platinum
Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound appears choppy - in this instance please follow the instructions below: 1.
Page 97: Important Information For Use
Operating Basics Important information for use Note the following limitations when you write to a video DVD: 1. Editing digital video ■ Log in with Administrator rights to use WinDVD Creator. ■ Make sure that your computer is running on AC power when using WinDVD Creator.
Page 98 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Page 99: Media Care
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 100: Sound System
Operating Basics 8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields.
Page 101: Modem
Adjust the equalizer settings to enhance sound quality. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.
Page 102: Region Selection
Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 103: Modem Selection
Operating Basics Open dialog box, if the modem and Telephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and telephony location are incorrect. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed.
Page 104 Operating Basics 1. Plug one end of the modular cable into the computer’s modem jack. 2. Plug the other end of the modular cable into a telephone jack. Telephone jack Modular cable Modem jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Page 105: Wireless Communications
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. User’s Manual...
Page 106: Bluetooth Wireless Technology
Please refer also to the electronic information which is included with each software. This Bluetooth™ Stack is based on Bluetooth™ Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth™ other than TOSHIBA mobile PCs.
Page 107: Product Support
TOSHIBA 1. Install: ® On Windows2000 or Windows XP, Bluetooth™ Stack for Windows TOSHIBA does not have a digital signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth™ Stack.
Page 108: Lan
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Page 109: Connecting Lan Cable
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 110: Cleaning The Computer
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 111: Using The Hard Disk Drive (Hdd) Protection
Operating Basics Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on hard disk drive. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and those signs in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.
Page 112: Toshiba Hdd Protection Properties
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.
Page 113: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
Page 114 Operating Basics 4-46 User’s Manual...
Page 115: Chapter 5 The Keyboard
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 116: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 117: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 118 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
Page 119 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 120: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 121: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 122: Temporarily Changing Modes
The Keyboard The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
Page 123: Generating Ascii Characters
The Keyboard Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
Page 124 The Keyboard 5-10 User’s Manual...
Page 125: Chapter 6 Power And Power-Up Modes
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
Page 126: Power Indicators
Power and Power-Up Modes Power conditions (continued) Power on Power off (no operation) AC adaptor Battery charge is • Operates not connected above low battery • LED: Battery off trigger point DC IN off Battery charge is • Operates below low battery •...
Page 127: Battery Types
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Indicates the AC adaptor is connected and Green supplying proper power to the computer. Indicates a problem with the power supply. Plug Flashing orange the AC adaptor into another power outlet.
Page 128 Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby Mode.
Page 129: Care And Use Of The Battery Pack
Refer to Chapter 9, Troubleshooting, for details. The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 130 Power and Power-Up Modes 3. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or a fire, and could also damage the battery pack. Always wrap the battery pack in plastic (or place it in a plastic bag) whenever transporting it, to avoid exposing the terminals to another conductive object which could result in serious injury.
Page 131 Do not turn on the PC’s power again until an authorized Toshiba service provider has checked it for safety. Continued use could cause a fire or rupture possibly resulting in serious injury or PC failure including but not limited to the loss of data.
Page 132: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 133: Battery Charging Notice
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off High capacity battery pack (8800mAh) about 5.0 to 21.5 about 4.5 Battery pack (4700mAh) about 3.5 to 13.0 about 3.0 RTC battery...
Page 134: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 135: Retaining Data With Power Off
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time about 9 days (Standby Mode) High capacity battery pack (8800mAh) about 135 days (Boot mode) about 5 days (Standby Mode)
Page 136: Replacing The Battery Pack
Power and Power-Up Modes Replacing the battery pack The battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life.
Page 137: Toshiba Password Utility
Battery lock Securing the battery pack 9. Turn your computer over. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User Password To start the utility, point to or click the following items: start ->...
Page 138 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 139: Supervisor Password
Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.
Page 140: Power-Up Modes
Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.
Page 141: Chapter 7 Hw Setup
Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 142: Power On Display
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 143: Boot Priority
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> The computer looks for bootable files in the CD-ROM −> LAN following order: HDD, floppy disk drive* CD-ROM* and LAN (Default).
Page 144 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. A bar will appear only under the selected device.
Page 145 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as built-in HDD ->...
Page 146 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key (PS/2 keyboard only).
Page 147 HW Setup This function lets you set the CPU operating mode. This option is displayed only for models with a Pentium-M ® processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled.
Page 148: Device Config
HW Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode.
Page 149: Configuring The Execute-Disable Bit Capability And Tpm
■ In most cases, changes to the system’s configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the configuration through the BIOS setup program, please be aware that the configuration set through the Windows applications will take priority.
Page 150: Ending The Bios Setup Program
Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
Page 151: Security Controller
■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
Page 152 HW Setup 7-12 User’s Manual...
Page 153: Chapter 8 Optional Devices
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ ExpressCard ■ SD card ■...
Page 154: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 155: Expresscard
ExpressCard The computer is equipped with an ExpressCard slot. Any ExpressCard that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports hot plug connection and utilizes the PCI-Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5 Gbps.
Page 156: Removing An Expresscard
Optional Devices To insert an ExpressCard, follow the steps below: 1. Insert an ExpressCard in the ExpressCard card slot. 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Inserting the ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard.
Page 157: Sd Card
TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Page 158: Removing An Sd Card
Optional Devices ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below.
Page 159: Memory Expansion
Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card can be created if required. Refer to the...
Page 160: Installing Memory Module
Optional Devices ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions as you can damage the computer and/or the module, and you risk losing data: a. The computer is turned on.
Page 161 Optional Devices 5. Slide your fingernail or a thin object under the cover and lift it off. Memory module cover Screw Removing the memory module cover 6. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 45 degree angle before pressing it down until the latches on either side snap into place.
Page 162: Removing Memory Module
Optional Devices 7. Seat the memory module cover and secure it with one screw. Be sure that the cover is closed firmly. Screw Memory module cover Seating the memory module cover 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up...
Page 163: Battery Pack
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Page 164: Battery Charger
Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Hard disk drive pack An extra hard disk drive expands the flexibility of your system and lets you carry your data without carrying the computer.
Page 165: Installing The Hard Disk Drive Pack
Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Hard disk drive pack Plastic tab Removing the hard disk drive pack Installing the hard disk drive pack To install the hard disk drive pack, follow the steps below. 1.
Page 166: Ultra Slim Bay Hdd Adaptor
Optional Devices Ultra Slim Bay HDD adaptor You can increase your computer’s data storage capacity by installing an additional 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Ultra Slim Bay. To install a hard disk drive in the Ultra Slim Bay HDD adaptor follow the steps below.
Page 167: Usb Floppy Disk Drive
Optional Devices 3. Close the lid and slid the lock to the lock position. Closing the lid For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics. USB floppy disk drive The USB floppy disk drive module can be connected to the USB port.
Page 168: Using The Toshiba Assist Button
You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard. To use “TV OUT” function by “TOSHIBA Assist button”, it is necessary to change the settings of “TOSHIBA Assist button” in advance. To open “TOSHIBA Controls” properties, click start, click Control Panel, click Printers and Other Hardware, select “TOSHIBA Controls”, and set...
Page 169: Displaying Movies On A Tv Or Crt
Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. Click the Settings tab and click the Advanced button. d.
Page 170: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 171 Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...
Page 172: Advanced Port Replicator Iii
■ i.LINK (IEEE 1394) port ■ DVI port DVI Monitors When you connect a TECRA S3 computer to an optional Advanced Port Replicator III, the Digital Visual Interface (DVI) supports the following DVI-D type monitors: ■ EIZO FlexScan L675 ■...
Page 173: Parallel Printer
7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, Setup. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 174: Serial Interface Devices
Optional Devices Serial interface devices The serial port can be used to connect to RS-232C compatible devices. RS-232C compatible devices include the following: ■ Modem ■ Mouse To connect a serial device, follow the steps below. 1. Turn the computer’s power off. 2.
Page 175: Troubleshooting
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 176: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 177: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 178: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 179: Overheating Power Down
Troubleshooting Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Standby Mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the DC IN indicator and DC IN indicator stops blinking.
Page 180 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
Page 181: Real Time Clock
5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
Page 182: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 183 Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power.
Page 184 Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 185 Troubleshooting Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM:...
Page 186 Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an Make sure the card is not write protected. SD memory card You cannot read a file Make sure the target file is on the SD memory...
Page 187: Infrared Port
Device tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. On-screen pointer The system might be busy. If the pointer is...
Page 188: Usb Mouse
Troubleshooting Problem Procedure Double-tapping Try changing the double-click speed setting in (Touch Pad) or the mouse control utility. double-clicking 1. Click start, click Control Panel, click (AccuPoint) does not Printers and Other Hardware and select work Mouse icon. 2. Click the Buttons tab. 3.
Page 189: Fingerprint Sensor
If problems persist, contact your dealer. Fingerprint System Please use TOSHIBA Password Utility to register Boot Authentication or the User Password if it was not registered. Single Touch Boot...
Page 190: Usb Device
Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
Page 191 Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Page 192 Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon.
Page 193: Wireless Lan
Troubleshooting Problem Procedure You cannot receive an Check the rings before auto answer setting in incoming call your communications application. You can also use the ATS0 command. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub.
Page 194 Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Bluetooth device communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer.
Page 195: Tv Output Signal
Troubleshooting TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, Keyboard.
Page 196: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 197: Specifications
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight 2.85 kilograms, configured with: 15"SXGA+, 256MB RAM, 40GB (typical) HDD, DVD-ROM&CD-R/RW drive, modem, LAN, Wireless LAN, 6cell battery pack. Weight will vary with other configurations. Above weights are measured at specific criteria.
Page 198 Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Full duplex Fax: Half duplex Communication Data...
Page 199: Display Controller And Modes
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. Two models are available: ■...
Page 200: Video Modes
Display Controller and Modes Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
Page 201 Display Controller and Modes Table 1: Video modes (VGA) continued Video mode Type Resolution Character Colors Scanning matrix frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
Page 202 Display Controller and Modes Table 2: Video modes (XGA model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual with LCD only) 1600 ×...
Page 203 Display Controller and Modes Table 2: Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual with LCD only) 1600 ×...
Page 204 Display Controller and Modes Table 2: Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual with LCD only) 1600 ×...
Page 205 Display Controller and Modes Table 3: Video modes (SXGA+ model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1400 × 1050 256/256K 256/256K 1600 ×...
Page 206 Display Controller and Modes Table 3: Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1400 × 1050 64K/64K 64K/64K 1600 ×...
Page 207 Display Controller and Modes Table 3: Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1400 × 1050 16M/16M 16M/16M 1600 ×...
Page 208: Powermizer
Display Controller and Modes PowerMizer The PowerMizer function is only available in nVIDIA models. PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below: Display Properties ->...
Page 209: Wireless Lan
Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Type III ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance. ■...
Page 210: Radio Characteristics
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Page 211: Supported Frequency Sub-Bands
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 212 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range 5150-5850 MHz Channel ID 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 User’s Manual...
Page 213: Toshiba Raid
Please refer to the TOSHIBA RAID help for details. ■ By changing this setting you are reconfiguring your hard disk.
Page 214: Windows Manual Setup
3. When the message “Setup will load support for the following mass storage device(s):” appears on the screen, press the S key and install the TOSHIBA RAID Driver using the TOSHIBA RAID Driver Disk that was created. 4. Follow the onscreen instructions to continue Windows setup.
Page 215 An effective way to ensure that such situations do not happen is to carry out RAID-1 media checks regularly. The TOSHIBA RAID utility is set as default to carry out media checks every month on the third Wednesday from noon.
Page 216: Starting, Modifying And Ending The Bios Setup Program
TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If Password = is displayed, enter the User Password and press the Enter key. Please refer to Chapter 6, the...
Page 217 TOSHIBA RAID 3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings.
Page 218 TOSHIBA RAID User’s Manual...
Page 219: Bluetooth Wireless Technology Interoperability
Appendix E Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
Page 220 TOSHIBA portable computers. Always use Bluetooth™ Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm...
Page 221: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 222 ■ Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth™ Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 223 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. The...
Page 224: Using Bluetooth™ Card From Toshiba Equipment In Japan
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 225: Approved Countries/Regions For Use (Bluetooth™ Wireless Technology
Do not install the embedded wireless module into other device. Approved Countries/Regions for use (Bluetooth™ wireless technology) Bluetooth™ Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 226 Bluetooth wireless technology Interoperability User’s Manual...
Page 227: Ac Power Cord And Connectors
Appendix F AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
Page 228 AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S.
Page 229: If Your Computer Is Stolen
What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below. ■ Attach a copy of your receipt showing where your computer was purchased.
Page 230: Toshiba Theft Registration
If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
Page 231 BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
Page 232 TOSHIBA Anti-theft Protection Timer User’s Manual...
Page 233 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 234 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Page 235 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 236 Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Page 237 Glossary components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
Page 238 Glossary disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk.
Page 239 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 240 Glossary HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can manipulate.
Page 241 Glossary level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing- side coating is etched into character forming segments with leads that extend to the edge of the glass.
Page 242 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. Glossary-10...
Page 243 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 244 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 245 2-12 hinge 2-9 location 2-7 opening 3-8 monitoring capacity 6-10 screen 2-10 real time clock 1-4 DLA for TOSHIBA 1-18 4-27 safety precautions 6-5 Docking interface 1-8 save mode 1-12 Documentation list 1-2 types 6-3 Dual Pointing Device 1-8...
Page 246 Index DVD Super Multi drive 1-6 Fn + F12 (ScrLock) 5-3 location 2-6 Fn + F2 (power save mode) 5-4 problems 9-10 Fn + F3 (standby) 5-4 using 4-16 Fn + F4 (hibernation) 5-4 writing 4-22 Fn + F5 (display selection) 5-5 DVD-ROM&CD-R/RW drive 1-6 Fn + F6 (internal LCD screen location 2-6...
Page 247 Index HW Setup 1-14 accessing 7-1 LAN 1-9 4-40 Boot priority 7-3 cable types 4-40 CPU 7-7 connecting 4-41 device config 7-8 disconnecting 4-41 display 7-2 jack 2-3 general 7-2 LAN active indicator 2-3 keyboard 7-6 Link indicator 2-3 LAN 7-7 problems 9-19 Parallel/Printer 7-8 USB 7-8...
Page 248 Self test 9-4 indicators 6-2 Sound system 9-17 panel on/off 1-12 6-16 System start-up 9-4 shut down mode (boot TOSHIBA support 9-22 mode) 3-10 Touch Pad/AccuPoint 9-13 standby mode 3-11 TV output signal 9-21 system auto off 6-16 USB 9-16...
Page 249 Standby 1-14 setting 3-11 System automatic 1-12 Video modes B-2 Video RAM 1-4 Volume control 2-2 TOSHIBA Assist 1-16 TOSHIBA Assist button 1-11 TOSHIBA ConfigFree 1-16 Wireless communication 4-37 TOSHIBA Controls 1-14 indicator 2-12 4-40 TOSHIBA Dual Pointing Device Wireless communication switch...
Page 250 Index Index-6 User’s Manual...

Toshiba Tecra S3 User Manual

Chapter 1 Introduction

Chapter 2 The Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Appendix A Specifications

Appendix B Display Controller and Modes

Appendix C Wireless LAN

Appendix D TOSHIBA RAID

Appendix E Bluetooth Wireless Technology Interoperability

Appendix F AC Power Cord and Connectors

Quick Links

Related Manuals for Toshiba Tecra S3

Summary of Contents for Toshiba Tecra S3