Unit shall comply with Personal Station Class II. Analog Receiver/Transmitter Specifications and Requirements The Subscriber Unit shall comply with TIA/EIA IS-95A and meet or exceed TIA/EIA IS-95. The Subscriber Unit shall comply with Mobile Station Power Class III (600mW). Samsung Electronics...
Page 4
General Introduction Memo Samsung Electronics...
: 13.7V DC (± 10%) Size and Weight including standard battery : 14.6 x 5.4 x 2.5 cm, 191 cc, 220 g (7.7 ounces) including extended-life battery : 14.6 x 5.4 x 3.35 cm, 250 cc, 226 g (7.9 ounces) Samsung Electronics...
Page 6
: above 65 dB + 90 kHz ~ 2f : above 63 + 10LOG (Py) dB (where f = carrier frequency, Py = mean output power in watts) Harmonic and Conducted Spurious Emissions : above 43 + 10 LOG (Py) dB Samsung Electronics...
Page 8
Intermodulation Spurious Response Attenuation : lower than 1% Rx power = -101 dBm Tone power 1 = -43 dBm Tone power 2 = -43 dBm Tone 1 offset from carrier = ±1.25 MHz Tone 2 offset from carrier = ±2.05 MHz Samsung Electronics...
Page 9
9 TV : Tx vocoder rate (8 is full rate, 1 is 1/8th rate) 10 RV : Rx vocoder rate (8 is full rate, 1 is 1/8th rate) 11 xx : Walsh code used in traffic channel 12 System acquisition state Samsung Electronics...
Page 10
SATx CHxxxx 5 RSSIxxx : RSSI value 6 CHxxx : Using Channel 7 Handset Status : 1 - Initialization state 2 - Idle state 3 - System Access state 4 - Voice channel state 8 System acquisition state Samsung Electronics...
Standard Battery Extended battery SCH-1500 MAIN EXTENDED BATTERY BATTERY PACK (Li-Ion, 850mAH) (Li-Ion, 1350mAH) PACK : BTL859S : BTL1359L Charging Time 3 hours 5 hours SEC. code GH43-10114A GH43-10113A DTC : DTC59 Figure 3-1 Charging the Phone and Battery Samsung Electronics...
Page 12
Tighten the antenna nut fully. Reassemble the two halves of the clamshell together. Adjust the mounting angle and tighten the two slotted screws. CRADLE ANTENNA CLAM SHELL MOUNT UPPER HANDS FREE BOX FIXED SCREW CLAM SHELL MOUNT LOWER Figure 3-2 Cradle Installation Samsung Electronics...
Page 13
Normal place is the sun visor. Once the microphone has been correctly positioned, connect the microphone wire to the MIC jack on the hands-free box. MOUNTING BRACKET Figure 3-3 Hands-Free Box Installation Samsung Electronics...
Page 14
(+) terminal, black wire to the vehicle metal edge that may damage it. chassis. Then connect the battery (-) terminal to the vehicle chassis. Connect the other end of the power cable to the PWR jack of the hands-free box. Figure 3-4 Cable Connections Samsung Electronics...
Slot Mode Slot mode. ÔYesÕ indicates the slot mode. m or i -changes the status. -store it. Slot Index Slot mode index. The higher, the longer sleeping time. 0 ~ 7 -to change, enter new one. -stores it. Samsung Electronics...
Page 16
-stores it. IMSI Mobile Network Code, current code is displayed. IMSI_MNC Number -to change, enter new one. -stores it. CDMA Access Overload Class, current status is displayed. CDMA ACCOLC Class number -to change, enter new one. -stores it. Samsung Electronics...
Page 17
-stores it. HOME SID SID written in the list, current status is displayed. 1700 Number -to change, enter new one. -store it. NID written in the list, current status is displayed. Number -to change, enter new one. -stores it. Samsung Electronics...
Slot mode. ÔYesÕ indicates the slot mode. Slot Mode m or i -changes the status. -store it. Slot mode index. The higher, the longer sleeping time. Slot Index 0 ~ 7 -to change, enter new one. -stores it. Samsung Electronics...
Page 19
Mobile ID 1234567890 4-2-3 Phone # NAM2 LCD Display Key in Function SVC Menum i Choose ÔPhone#Õ. 1:Phone# 2:General 3:NAM1 4:NAM2 Choose ÔNAM2Õ. Phone # 1:NAM1 2:NAM2 Phone # Phone number 1234567890 Mobile ID # Mobile ID 1234567890 Samsung Electronics...
Page 20
-stores it. SID written in the list, current status is displayed. HOME SID Number -to change, enter new one. 1700 -store it. NID written in the list, current status is displayed. Number -to change, enter new one. -stores it. Samsung Electronics...
Page 21
-stores it. SID written in the list, current status is displayed. HOME SID Number -to change, enter new one. 1700 -store it. NID written in the list, current status is displayed. Number -to change, enter new one. -stores it. Samsung Electronics...
Page 22
NAM Programming Memo Samsung Electronics...
Caution : When you use the PST program with a notebook PC, you might encounter some problems. Check your serial port setup in your notebook PC (see your notebook PC manual). DonÕt worry about the serial port setup when you use a desktop PC. Samsung Electronics...
<Alt-X> key, and the PST program is over. Use this command to enter the name of a file whose extension is ÒmmcÓ. The values read from the named file will initialize the parameter values seen on the ÒEdit Parameters.Ó Samsung Electronics...
Page 25
All fields display the question marks instead of data. After reading from a phone or a file, if the question marks still show in a field, then that item has never been written to the phone or saved to the file. Samsung Electronics...
Page 26
3. Press <ALT-D> key to begin download. Various messages and progress bar will inform the user of the progress of the download. Caution : DO NOT REMOVE POWER WHILE THE PHONE IS BEING DOWNLOADED ! 4. Press <Esc> key to return to Main Menu. Samsung Electronics...
LCD module contains a controller which will display the information onto the LCD by 8-bit data from the MSM. It also consists a DC-DC converter to supply -3.5V for fine view angle and LCD reflector to improve the display efficiency. Samsung Electronics...
Page 28
Digital Converter (ADC) reference clock used in SLEEP/ changes to LOW, all the pins except for the TX mode. TXCO is disabled. ¥CHIPX8 : ADC reference clock used in CDMA RX mode. ¥FMCLK : Reference clock in FM RX mode. Samsung Electronics...
2 serial LPF consisting of R341, C342, R340, and C341, amplified at the speaker amp (U330), and comes out to speaker. In hands-free mode, the key tone is applied to RX audio line through the LPF and C338, R335. Samsung Electronics...
Page 31
The band width is 60MHz. DUPLEXER Duplexer (F406) controls to transmit through the antenna only the signals within acceptable Tx frequency range (1880 ±30MHz). It also matches LNA (U401) input in receiving part and PA out in transmitter part with the antenna. Samsung Electronics...
Page 32
The RF BPF (F403) passes only a specific frequency LNA (U404) input in receiving part and PA out in (881.49±12.5MHz) from the signal received from the transmitter part with the antenna. mobile station. The band width is 25MHz. Samsung Electronics...
Page 33
The signal out to BBA (Base Band Analog) should supplies 4.2V to the others. be a constant level. The TX IF AGC amp (U501) controls power to keep the signal at a constant level. Dynamic range is 85dB, up gain -40dB, and down gain -45dB. Samsung Electronics...
Page 34
The TX IF AGC Amp (U501) TX AGC Amp (U501). U130 supplies 4.8V to power controls power to keep the signal at a constant level. amp (U571). Dynamic range is 85dB, up gain -40dB, and down gain -45dB. Samsung Electronics...
Page 35
Secondary filter : L1, L2, C9, C12 This circuit minimizes the ripple noise in the dc VOLTAGE DETECTION : HIC signal output from the rectifier. HIC pin 12 and 13 detect the input voltage which applies to u-COM A/D terminal. Samsung Electronics...
Secondary filter circuit : L20, C22 It minimizes the high frequency ripple noise, which is caused by primary oscilation. Reverse current protection circuit : D20 When power is off, it protects the reverse flow of current from battery pack. 6-10 Samsung Electronics...
Page 37
ID and GND. reference voltage. CURRENT DETECTION CIRCUIT : R14, R15, R16, U4 Battery charging current is changed voltage through R14, R15, R16. This voltage inputted U-COM to 16 times amplifiered through U4. Samsung Electronics 6-11...
Protection Circuit is the circuit against the (Cigarette Lighter Adapter) for the SCH-1500 electrical stress which is occured at unexpected DBDM phone of SAMSUNG. conditions of the source power of CLA unit such as reverse voltage or overcurrent. ¥ Detection of DBDM phone...
Page 39
HHP, and to convert from u-processor controls this circuit to attenuate echo hands-free mode to private mode, and vice verse. It which may occur in Land side. adjusts speaker volume at 8 steps and attenuates echo and noise occurred during conversation. Samsung Electronics 6-13...
34(A2, 0, 0) T_CDATA_I Transmit continuous 5-word Reverse CTL CH message. 35(A3, 0, 0) T_VOLUME_UP_I Increase value of the last command. (Only for autotest) 36(A4, 0, 0) T_VOLUME_DOWN_I Decrease value of the last command. (Only for autotest) 6-14 Samsung Electronics...
Page 41
Change pdm TX AGC in CDMA. 72(D2, 3, 0) T_AMPS_TXADJ_I Change pdm TX AGC in AMPS. 73(D3, 1, 0) T_SET_PA_R_I Set PA R1, R0 in CDMA. 74(D4, 4, 0) T_TXRAS_ADJ_I TX Ras table adjust. 75(D5, 0, 3) T_READ_RSSI_I Read a RSSI. Samsung Electronics 6-15...
Page 42
EEPROM, use T-SAVE-VAL-I command to store the test value into the corresponding position. *OP: Operation Command Number AB: Input Argument Byte Number RB: Return Byte Number *SAT 32, 33 are not operating in MSM2 CHIP test *46 command is required in Rx, and Tx path test at AMPS mode. 6-16 Samsung Electronics...
Test Cable Duplexer Out Antenna In From To ANT In Duplexer Out RF In/Out HP83236B Directional Coupler Test Jig DC Power Supply (+7.2 V) 7-2-2 Hands-Free HANDS FREE KIT BOX ANTENNA CRADLE DATA DC POWER Orange SUPPLY Black (+13.7V) Samsung Electronics...
Page 44
CONNECT TO DB25 CONNECTOR OF CONNECT TO HHP TEST CABLE BNC CONNECTOR CONNECT TO RF IN/OUT PORT OF TEST EQUIPMENT Cable Loss : 1.2 ~ 2.1 dB Items needed to purchase from SAMSUNG ITEMS PARTS# REMARK RF TEST CABLE GH97-00687A * Cable Loss : 1.9 GHz (PCS) 2.1 dB, 800 MHz (Cellular) 1.2 dB...
Page 45
[SEND]/[END/ ] keys. ¥ The command [0 7] means carrier on. ex) [7 2 X X X] ¥ If you enter the command [3 4] you can ¥ [#] key means the escape of current command. spread the carrier. Samsung Electronics...
Page 46
Test Procedure Memo Samsung Electronics...
U120 pin 3,4 input =5.2V? Check U120 and its neighboring circuits Check U110 and its neighboring circuits. U110 pin6 input = S5.2V? U120 pin 6 output=3.3V? Check U120 and its neighboring circuits. U110 pin 4 output=3.3V? Check U110 and its neighboring circuits. Samsung Electronics...
Page 48
U200 pin59, U600 pin79. U600 pin 52? Check the LED and its neighboring LED on? circuits. Replace if required. Normal initial Check the LCD pins and its neighboring display on LCD? circuits. Replace if required. Samsung Electronics...
Page 49
U100 pin 60 drive Q140 Replace if required. through R144? Check R146, R147, R148 and Normal Q141 operation? Q141. Replace if required. The voltage applied Resolder R141 and R142. to LCD pins 38, 41? Backlight LED on Samsung Electronics...
Page 50
8-1-4 Abnormal Key Data Input Check initial status. Scanning signals Resolder U100 pins 159, 160 outputted from U100 pins159, and 163-167. 160, 163-167? Resolder U100 pins 168, 169, 170, 172 and 173. Resolder J100. Normal Key data input? Replace the Keypad assembly. Samsung Electronics...
Page 51
U100 pin 49? CLK waveform applied Resolder R341, C342, R340, C341, from U330 pin 2? C337, and C334 Check U330, C333, and C334. CLK waveform applied Replace if required. to U330 pin 3? Normal keytone? Replace the Keypad assembly. Samsung Electronics...
Page 52
Check U100 pin 56. Replace if required. Check Q350, Q351, R350 and D350. CLK waveform applied Replace if required. to J100 pin 12? Is the buzzer Connect the buzzer correctly. connection correct? Check the buzzer and replace if required. Samsung Electronics...
Check PLL OK? U524(PCS) (AMPS) RF out TX IF Level OK? local level. Level OK? AMPS:-21dBm AMPS:-17dBm AMPS:-10dBm PCS:-13dBM PCS:-4dBM PCS:-3dBm Check U550(PCS) Check U522 (PCS) U562(AMPS) RF U571(AMPS) Out level OK? Pout level. AMPS:3dBm AMPS:28dBm PCS:7dBm PCS:23dBm Samsung Electronics...
Page 56
Set Bat. B as Trickle charge mode Trickle charge mode Bat. B Bat. A Bat. B removed? Bat. A removed? charging finished? charging finished? Set Bat. B as Set Bat. A as Trickle charge mode Trickle charge mode 8-10 Samsung Electronics...
Page 57
Is LED turned on ? Is Q7 turned on? Change AH1504F Check R14, 15, 16, U2B, U2A Is Q7 turned on ? Check F1, L1, AH1504G Is charge curent Check R14, 15, 16, U2B, U2A over 630mA ? Samsung Electronics 8-11...
Page 58
Is battery pack connected ? Connect battery to a phone Is the value of V/F correct ? Battery pack fault Is the voltage at Check F1, U1, U3, Q8, Q7 pin-5 of U1 high ? Check the interface plug and phone 8-12 Samsung Electronics...
Page 59
Check Q6, U2B, Q4, U1 Is the voltage at Check R6, R7, VR1, U4 R7 under 2.48V ? Is the voltage at Check F1, U1, U3, Q8, Q7 pin-5 of U1 high ? Check the interface plug and phone Samsung Electronics 8-13...
Call on Signal Check. and R101, more than 12V(?). Q13, E2 Check To connect Hand Set. Check low state HFPWR > 12V from MGND. Check low STATE from R96 and, Check EXPWR > 12V R19//18//18+//18++//17 (more than 0.3V ?) 8-14 Samsung Electronics...
Page 61
Check C12, R34, and 35 Check U6C(8PIN), Signal OK? Check C14, and U7 SPEAKER Check SPEAKER, output OK? Check SPK PIN, Signal OK? Check Cradle, and Cable Check U8B(7PIN), Signal OK? Check U8, R72, 49, 60, and U10 Samsung Electronics 8-15...
Page 62
Troubleshooting 8-7-3 Data Comm & Cont. Check INTPWR PIN, and U4 Check MPU (1PIN), 5V? Normal X1 output? Check C40, and C41 Check MPU 17, and 18PIN, Check D11, D15, Q11, and 12 DATA PULSE? 8-16 Samsung Electronics...
9-11 Main Packing Layout 9-11-1 Main Packing Layout (with DTC) 9-11-2 Main Packing Parts List (with DTC) 9-11-3 Main Packing Layout (with TC) 9-11-4 Main Packing Parts List (with TC) 9-12 Hands-Free Kit Packing Layout 9-13 Hands-Free Kit Packing Parts List Samsung Electronics...
Page 97
0501-000457 Q351 Digital, DTA144EE 0504-000172 Q380 Digital, DTC144EE 0504-000168 Q390 Small Signal 0501-000457 Q391 Small Signal 0501-000218 Q581 Small Signal 0501-000162 Q582 Small Signal 0501-000218 Q583 Small Signal 0501-000462 Q690 Digital, DTA114EE 0504-001016 Q741,Q742,Q751,Q752 Digital, DTC114EE 0504-000167 Samsung Electronics 11-9...