Table of Contents
Related Manuals for Miele G 1570
Summary of Contents for Miele G 1570
-
Page 1: Operating Instructions
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. M.-Nr. 06 702 730... -
Page 2: Table Of Contents
Contents Description of the appliance ......... 5 Appliance overview . - Page 3 Contents Operation ............32 Detergent .
- Page 4 Contents Problem solving ..........57 Cleaning the water inlet filter .
-
Page 5: Description Of The Appliance
Description of the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i In-operation indicator light d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent (depending on model) dispenser... -
Page 6: Control Panel
This instruction book applies to several different dishwasher models. The specific dishwasher models below are referred to as follows: G 1570 = G 1XXX G 2570 = G 2XXX The model numbers G 1XXX and G 2XXX used in this book refer to the model designation specified on the data plate of the appliance (and not the description on the control panel). -
Page 7: Warning And Safety Instructions
Warning and Safety instructions Delivery This appliance conforms to current Before setting up the appliance, safety requirements. Inappropriate check it for any externally visible use can, however, lead to personal damage. Under no circumstances injury and damage to property. To should you use a damaged appliance. - Page 8 Switch off at the mains If you want to convert your and call your Miele supplier or the Miele freestanding dishwasher to a Service Department. built-under ("U") model, you will need to The plastic housing of the water order the appropriate conversion kit.
- Page 9 Warning and Safety instructions Avoid leaving the door open On models with "Delay start", make unnecessarily, as you could trip sure that the dispenser is dry over it. before adding detergent. Wipe dry if necessary. Detergent will clog if poured Do not sit or lean on the opened into a damp dispenser and may not be door.
-
Page 10: Disposal Of Your Old Appliance
If the connection cable is damaged it must be replaced with a Miele – The dishwasher is correctly installed cable by a Miele approved service and plumbed in. technician only. -
Page 11: Caring For The Environment
Caring for the environment Disposal of the packing It should be unplugged or disconnected from the mains electricity material supply by a competent person. The The transport and protective packing plug must be rendered useless and the has been selected from materials which cable cut off directly behind it to are environmentally friendly for disposal prevent misuse. -
Page 12: Before Using For The First Time
Before using for the first time To open the door To close the door ^ Push the baskets right in. ^ Then lift the door upwards and push until it clicks into position. ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted. -
Page 13: Before Using The Appliance For The First Time You Require
Before using for the first time Before using the appliance for Every dishwasher is tested at the the first time you require: factory. – approx. 2 litres of water, There will be residual water in the appliance from this test. It is not an –... -
Page 14: To Call Up The Water Hardness Level In The Display
Before using for the first time To call up the water hardness level in the display °d mmol/l °f Value displayed German After your dishwasher has been scale through one programme cycle (e. g. Pre-wash), you can check the water hardness level measured by the water softener sensor in the display. -
Page 15: External Water Softening System
Before using for the first time External water softening The number after the p in the display is the water hardness level in °d (see system chart). If your dishwasher is connected to an ^ Use the programme selector button external water softening system which to select the value which uses salt to reactivate, you will still need... -
Page 16: Filling The Salt Reservoir
Before using for the first time Filling the salt reservoir If the water in your area is very soft In order to achieve good cleaning and constantly lower than results, the dishwasher needs to 0.7 mmol/l (4 °d) you do not need operate with soft water. -
Page 17: Salt Indicator
Before using for the first time Salt indicator ^ Remove the lower basket and unscrew the salt reservoir cap. ^ Fill the salt reservoir with dishwasher salt when the salt indicator light Only open the salt reservoir when comes on. (If it comes on during a you want to fill it with dishwasher salt programme, wait until the end of the as water or salt solution will run out... -
Page 18: Rinse Aid
Before using for the first time Rinse aid Adding rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically. -
Page 19: Rinse Aid Indicator
Before using for the first time Rinse aid indicator When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. -
Page 20: Setting The Rinse Aid Dosage
Before using for the first time Setting the rinse aid dosage p 3 will flash in the Display. This means that the rinse aid dosage The rinse aid dosage can be set from has been set to 3 ml to the factory. approx. -
Page 21: Loading The Dishwasher
Loading the dishwasher Note – Deep based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water. -
Page 22: Items Not Suitable For Dishwashers
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –... -
Page 23: Upper Basket
Loading the dishwasher Upper basket Spiked insert The spiked insert can be removed to For safety reasons, do not make more room for larger items such operate the dishwasher without the as casserole dishes. upper and lower baskets in place. To remove it a ^ Use the upper basket for small, ^ Pull it upwards by the handle as... -
Page 24: Hinged Cup Rack
Loading the dishwasher Hinged cup rack Positioning rail (depending on model) ^ To make room for tall items raise the Glasses can be arranged along the rack upwards. positioning rail to give them some support during the programme. G 2XXX models: You can set the cup rack at two different heights. -
Page 25: Support Rail (Depending On Model)
Loading the dishwasher Support rail (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the rail and lean tall glasses against it. ^ You can also remove a section of the cutlery tray to make more room for tall glasses. -
Page 26: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or upper basket, the upper basket can be Dishwasher with cutlery tray adjusted on three levels with 2 cm (see data plate for model number) -
Page 27: Lower Basket
Loading the dishwasher Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. -
Page 28: Variable Inserts
Loading the dishwasher Variable inserts Wide vario insert A variety of inserts are available for washing cups, glasses, plates, saucers, pots and pans in the lower basket. Vario inserts Removing the wide vario insert a ^ Pull upwards by the handle to remove. -
Page 29: Bottle Holder
Loading the dishwasher Removing the narrow vario insert Bottle holder The bottle holder can be used to wash narrow items, e.g. milk and baby bottles. ^ Press the insert downwards a and the catch inwards b at the same time. ^ Place the bottle holder as shown in the bottom basket. -
Page 30: Cutlery
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, place them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 31: Cutlery Basket (Depending On Model)
Loading the dishwasher Cutlery basket (depending on model) ^ Fit it into the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. -
Page 32: Operation
Operation Detergent Avoid inhalation of powder Only use detergents formulated detergents and do not ingest for domestic dishwashers. Do not dishwasher detergent. Dishwasher use washing up liquid. detergents can cause burning in the nose, mouth and throat if swallowed, ^ You can use conventional powder or inhibit breathing. -
Page 33: Adding Detergent
Operation Adding detergent For information Compartment I holds max. 10 ml, Compartment II holds max. 50 ml. There are markings in compartment II to assist with dispensing: 20, 30. The marks indicate a level of approx. 20 or 30 ml when the door is open in a horizontal position. -
Page 34: Switching On
Operation Switching on Starting a programme ^ Open the stopcock, if it is closed. ^ Select the programme required with the programme selector button. ^ Open the door. The indicator for the programme ^ Make sure the spray arms are not selected lights up. -
Page 35: Display
Operation Display At the end of a programme The duration of the programme At the end of a programme, the selected appears in hours and minutes In-operation indicator light will be in the Display before the programme visible flashing slowly with the door begins. -
Page 36: Switching Off
Operation Switching off Unloading the dishwasher At the end of a programme: Dishes tend to break and chip more easily when they are hot. ^ Open the door. Allow the dishes to cool until they are ^ Switch the dishwasher off using the comfortable enough to handle before Off button o. -
Page 37: Interrupting A Programme
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as Important: the door is opened. If the detergent dispenser flap has If the door is closed again, the already opened, do not change the programme will continue from the point programme. -
Page 38: Additional Functions
Operation Additional functions Do not select the "3 in 1" function if: – using "2 in 1" tabs (detergent with Tab function rinse aid) – if your water hardness level is above You can programme your dishwasher to ensure excellent results when using 3.8 mmol or 21 °d. -
Page 39: Delay Start
Operation ^ Open the door. Delay start ^ Switch the dishwasher on with the On The start time of a programme can be button g. delayed, e.g. to benefit from economy rates of electricity. A delay start time of The On indicator light g comes on. between 30 minutes and 24 hours can ^ Select the programme required using be selected. - Page 40 Operation The time starts counting down until the Starting a programme before the programme start time: in 1 hour steps Delay start period has elapsed for delay start periods of over 10 hours, A programme can be started before the and in minutes for delay start periods of Delay start period has elapsed.
-
Page 41: Buzzer
Operation ^ Press the Tab button four times. Buzzer A buzzer sounds at the end of the The "3 in 1 Tab" indicator will flash programme or if there is a fault. briefly four times at intervals. You will hear the buzzer at the end of a The characters flashing in the Display programme in bursts of five with a short show whether the buzzer at the end of... -
Page 42: Factory Default Setting
Operation Factory default setting The characters flashing in the Display show whether a setting other than the If you have altered any settings from factory default setting has been set. the factory default, you can re-set them back to the factory default settings as –... -
Page 43: Adjust Sensor Wash
Operation Adjust sensor wash The characters flashing in the Display show whether the "Adjust sensor wash" You can adjust the sensor wash function is activated or deactivated. programme so that it will remove – "p 1": The "Adjust sensor wash" stubborn soiling in a lightly soiled load. -
Page 44: Cleaning And Care
Miele ^ Replace the reflector panel in its dishwasher cleaner (available from the holder. -
Page 45: Cleaning The Control Panel
These would damage the surface their chemical composition, they structure. could cause serious damage to ^ Clean the front using a Miele E-Cloth surfaces. or with a suitable cleaning agent for ^ This should only be wiped with a the type of material the front is made of. -
Page 46: Cleaning And Care
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet ^ Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. - Page 47 Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press together the catches in the ^ Then turn the handle clockwise to direction of the arrows a as shown, and open the filter b.
-
Page 48: Cleaning The Spray Arms
Cleaning and care Cleaning the spray arms ^ Remove the lower basket. Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. -
Page 49: Problem Solving Guide
With the aid of the following guide, minor problems can be easily corrected without calling in a Miele service technician, saving you both time and money. The following guide may help you to find the reason for a fault, and to correct it. - Page 50 Problem solving guide Problem Possible cause Remedy The In-operation There may be a Switch the dishwasher off with the Off button o. indicator is flashing technical fault. quickly. After a few seconds: The buzzer is sounding. – Switch the dishwasher All the programme back on.
-
Page 51: The Dishwasher Does Not Fill/Drain
Problem solving guide The dishwasher does not fill/drain Problem Possible cause Remedy The In-operation The stopcock is – Open the stopcock fully. indicator is flashing closed. quickly. The buzzer is sounding. The Inlet/Drain indicator flashes when the door is open. The dishwasher stops Before rectifying the problem you during a programme. -
Page 52: General Problems
Problem solving guide General problems Problem Possible cause Remedy The In-operation Items are blocking Open the dishwasher door and indicator is flashing the path of the middle rearrange the items which are quickly. spray arm. obstructing the spray arm. The "Check spray The middle spray arm –... -
Page 53: Noises
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Rattling noise in the Items of crockery are Interrupt the programme, wash cabinet. -
Page 54: Unsatisfactory Washing Result
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher" The programme was not Select a more intensive powerful enough. programme. See "Programme chart". There is some stubborn Use the "Adjust sensor soiling although most of the... - Page 55 Problem solving guide Problem Possible cause Remedy Dishes, cutlery and The rinse aid amount may Replenish the reservoir, glasses are not dry be insufficient or the rinse increase the dosage or or are flecked. aid reservoir empty. change the brand of rinse aid.
- Page 56 Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull The glassware is not There is no remedy. and discoloured;...
-
Page 57: Problem Solving
^ Replace the filter and seal, making union. This filter is available from the Miele Spares Parts dept. sure they are sitting correctly. ^ Reconnect the inlet hose to the Cleaning the filter:... -
Page 58: Cleaning The Drain Pump And Non-Return Valve
Problem solving Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. Watch out for glass or bone splinters which could cause injury. -
Page 59: After Sales Service
– your Miele dealer, or technology. – the Miele Service Department The "PC" indicator light is used as the (see back cover for contact details). -
Page 60: Programme Chart
Programme chart Programme When to use Sensor wash Sensor controlled programme for normally soiled crockery Quick wash 40 °C "Quick programme" for lightly soiled crockery, e.g. party crockery; for flushing out salt residues after replenishing the salt reservoir; includes sensor controlled glass care; not suitable for tablet detergents. - Page 61 Programme chart Programme sequence Consumption Duration Energy kWh Water h:min Pre- Main Interim Final Drying Cold Litres Cold wash wash rinse rinse water water water water connec- connec- connec- connec- tion tion tion tion (15 °C) (55 °C) (15 °C) (55 °C) 0.95-1.35 0.6-0.8 10-17 1:36-2:38 1:34-2:23...
-
Page 62: Optional Accessories
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer or from the Spare Parts Department (some may be supplied as standard depending on model). If you would like to …... -
Page 63: Electrical Connection
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 The fuse cover must be refitted when All electrical work must be changing the fuse, and if the fuse cover carried out by a suitably qualified is lost, the plug must not be used until a and competent person, in suitable replacement is obtained. -
Page 64: Plumbing
Plumbing Connection to the water supply Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max. 60 °C. We would only recommend connection to a hot water supply if it is economical, e.g. -
Page 65: Drainage
Plumbing Drainage Venting the drainage system – The appliance drainage system is If the on-site drain connection is fitted with a non-return valve, which situated lower than the guide path for prevents dirty water from flowing the bottom basket rollers in the open back into the dishwasher via the door the drainage system must be drain hose. -
Page 66: Technical Data
Technical data Dishwasher model G 1XXX G 2XXX Height 80.5 cm 84.5 cm (adjustable + 6.5 cm) (adjustable + 6.5 cm) Height of building-in min. 80.5 cm (+ 6.5 cm) min. 84.5 cm (+ 6.5 cm) recess Width 59.8 cm 59.8 cm Width of building-in 60 cm... - Page 68 Alteration rights reserved / M.-Nr. 06 702 730 / 01 M.-Nr. 06 702 730 / 01 G1570/G2570 / 0806 gb - GB...