Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ABB EnRack
Summary of Contents for ABB EnRack
- Page 1 — U S E R M A N UA L EnRack remote racking solution...
-
Page 3: Table Of Contents
U S E R M A N U A L — Table of contents Safety information Introduction Safety precautions 07– 09 EnRack solution Storage 11– 12 Installation and commissioning 13–16 Operation Maintenance Additional information... -
Page 4: Safety Information
CAUTION NOTICE avoided. the EnRack pendant controller. Whenever changes are made to the device NOTICE configuration, measures should be taken to avoid inadvertent tripping. -
Page 5: Introduction
— Introduction — This manual Table 1. Related documents This manual contains the information required to install and operate the EnRack remote racking Document title Document ID solution for AMVAC™ and ADVAC™ draw-out circuit SafeGear Technical Guide 1VAL108002-TG breakers supplied with the Breaker-Borne Racking... -
Page 6: Safety Precautions
E N R A C K S O L U T I O N — Safety precautions Hazard of electric shock, explosion or arc flash • Before performing any of installation or operation, it is recommended to read and understand all instructions provided in this manual. -
Page 7: Enrack Solution
Based on functional requirements, the EnRack Motor overload × × solution is available in two variants. indication (optional) 1. EnRack: Breaker rack in and rack out. if OLR is connected 2. EnRack+: Breaker open, breaker close, rack in Error indication × ×... - Page 8 Figure 1 shows a simplified block diagram of operations. EnRack solutions. Both the EnRack controller module and EnRack relay module must be installed RACK IN key is used to RACK IN the circuit breaker in the low voltage compartment* following the from disconnect to test or test to connect position.
- Page 9 U S E R M A N U A L BREAKER CLOSE key is used to close the breaker — The EnRack+ controller performs breaker rack in, 03 EnRack controller from the open position. The user must press and breaker rack out, breaker open and breaker close, module —...
-
Page 10: Storage
ABB recommends that the pendant be placed Inform the nearest ABB office or representative. inside the pendant carry case or the pendant ABB should be notified immediately if there are any box mounted on the switchgear compartment discrepancies in relation to the delivery documents. -
Page 11: Installation And Commissioning
ABB part number 7GIS3844001. switchgear construction and are designed to be mounted on a standard DIN rail. The modules must be tested with the EnRack briefcase tester in accordance with the test Installation of the modules into existing installed instructions that come with the tester. - Page 12 Operation section. Safe disposal • For instructions on clearing data, see page 16 • Clearing of all data stored in the EnRack system of this manual. is recommended before disposal of product. • After clearing data, turn off the product and •...
-
Page 13: Operation
U S E R M A N U A L — Operation • Prior to and during operation of EnRack, when circuit breaker in motion from disconnect position equipment is energized, ensure that all personnel to test position. remain outside the arc-flash boundary. - Page 14 E N R A C K S O L U T I O N Breaker open Note: Before performing breaker open, make sure the 1. When the breaker is in disconnect position, no circuit breaker is in the closed status within the input power is available to the breaker open or test or connect position and no error code is breaker close coils;...
- Page 15 U S E R M A N U A L — Table 5. EnRack pendant error codes Breaker status Relay outputs Closed Open Disconnect Test Connect Racking Error code Error message on display Err 01 Unknown Position × × Err 02 Locked in Disconnect ×...
- Page 16 LCD display. — — Events The EnRack system records the last 20 events Note: The stored events and breaker operations or alarms, such as rack in, rack out, breaker open reflects only operations performed through the and breaker close.
-
Page 17: Maintenance
U S E R M A N U A L — Maintenance Firmware updates Firmware can only be updated in the factory. Please contact an ABB support engineer for instructions on how to upgrade the firmware. Additional information Instructions for tester User/tester may need to follow only chapters 1 and 2 to perform boot loader firmware update. - Page 18 E N R A C K S O L U T I O N...
- Page 20 The information contained in this document is for general information purposes only. While ABB strives to keep the information up to date and correct, it makes no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability,...