4-3-8 When the remote control is not receiving ................. 4-4 PCB Inspection Method 4-10 ........................4-4-1 Pre-inspection Notices ..........................4-10 4-4-2 Inspection Procedure ..........................4-10 4-4-3 Indoor Detailed Inspection Procedure ..................... 4-10 4-5 Main Part Inspection Method 4-11 ......................Samsung Electronics...
Page 3
7-1-2.Display ................................18. Reference Sheet ..........................8-1 Refrigerating Cycle Diagram ......................8-2 Index for Model Name ........................8-3 Pressure & Capacity mark ........................ 8-4 Low Refrigerant Pressure Distribution ..................8-5 Installation Diagram of Indoor Unit and Outdoor Unit ............. Samsung Electronics...
Check the distance between the product and the other electronic appliances such as TV, Video, and audio. It should be over 2m. - If not, it causes a bad picture quality or a noise. Repairing the products by consumer should be strictly prohibited. - There is a danger of electric shock or fire due to incorrect disassembly. Samsung Electronics...
- There is a danger of electric shock. In case the product will not be in use for a long time, the battery of remote control should be kept separately. - Leakage of inside fluid can cause break down of remote control. Samsung Electronics...
Catechin,extracted from the green tea,is contained in the filter and deactivates captured bacteria and unpleasant odors. Silver Nano Evaporator Deodorizing Filter Activated carbon is incorporated in the filter,efficiently absorbing cigarette smoke, pet odors, and other unpleasant smells, replacing them with clean,refreshing air. Anti-Bacterial Cross Fan Samsung Electronics...
AQ12EWGN(X)SER AQ12EWFN(X)SER Indoor Design changed Indoor Front Display changed Outdoor chassis changed Basic model New model Modified New contents part and characteristic AQ09ESGN(X)SER / AQ12ESGN(X)SER AQ09EWFN(X)SER / AQ12EWFN(X)SER Indoor Design changed Indoor Front Display changed Outdoor chassis changed Samsung Electronics...
2-3 Accessory and Option Specifications 2-3-3 Optional Accessories Item Descriptions Code-No. Q'TY Remark RUBBER-LEG DB73-20134A Outdoor Unit DRAIN-PLUG OUT DB67-20011A NOTE: If these accessories are supplied , they will be in the accessory box. Samsung Electronics...
*Protective function : Low temperature release. *Evaporator cleaning time can vary, depending on the (Prevention against freeze) previously used mode. 1) Auto(COOL),COOL,DRY MODE : approximately 30 minutes. 2) Auto(HEAT),HEAT,FAN MODE : approximately 15 minutes. Samsung Electronics...
FRONT.(use + Screw Driver) 4) Loosen connector wire(white) and detach the temperature sensor wire. 5) To detach the FRONT-PANEL the main frame, unfasten 2 screw at the bottom.(use + Screw Driver) 6) Take off the FRONT-PANEL,lifting up the bottom. Samsung Electronics...
Page 15
1) Unfasten the earth screw.(use + Screw Driver) 2) Detach the temperature sensor and Humidity sensor. 3) Detach COVER-CONTROL from the CASE- CONTROL. 4) Loosen MPI connector wire(yellow), and MOTOR wires(white,blue). 5) Take off the CASE-CONTROL from the main frame. Samsung Electronics...
Page 16
1) Unfasten the screw. 2) Cut the cable tie. 3) Loosen the terminal block wires. (Total 4EA: #N(1)-2EA, #2-1EA, #3-1EA) Caution: The terminal is the locking type. So, when you separate terminals, pull pressing the button. Button Samsung Electronics...
Page 17
Option connector. Caution: When you separate the connector, pull pressing the locking button. 7) Loosen the Relay #4 blue-connector(RY71). Caution: The terminal is locking type. So, when you separate terminals, pull pressing the button. Button Samsung Electronics...
Page 18
When you separate the connector, pull pressing the locking button. 12) Take off the main PBA from the ASS’Y Control in. Caution: When you take off the PBA, don’t touch the components. Please hold the PBA both side. Samsung Electronics...
Page 19
1) Unfasten the screw at the right side. (use + Screw Driver) 2) Unfasten the screw at the left side. (use + Screw Driver) 3) Detach the HOLDER PIPE. 4) Take off the EVAPORATOR from the main frame. Samsung Electronics...
Page 20
2) unfasten the 3 points screws in the CASE- CONTROL, and then detach the CASE. (use + Screw Driver) 3) unfasten the screw a little.(use + Screw Driver) 4) Lift up the evaporator slightly and pull the CROSS-FAN to the left side. Samsung Electronics...
Cover Control. 3) Separate the connection wire from the Terminal Block. 4) Loosen 6 fixing screws and separate the Cabinet Front. 5) Loosen 1 fixing screw of Ass’y E-part. 6) Loosen 12 fixing screws and separate the Cabinet-Side Samsung Electronics...
Page 22
Compressor 1) Open the Terminal Cover of Compressor and unscrew the Connection Terminal. 2) Disassemble the inlet and outlet pipe of Compressor by welding. 3) Loosen 3 bolts of the lower part. 4) Separate the Compressor. 3-10 Samsung Electronics...
SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 NOTE: SEG1,SEG7,SEG13,SEG19 need not to be pressed in,so in fact the Option No.we should press in is as below. Samsung Electronics...
NOT USED HUMIDITY SENSOR ERROR(IN TEST MODE) LED ON LED OFF LED BLINKING " E162 " Error is displayed only in test mode. So, if you want to check,please push the power button of indoor unit. Samsung Electronics...
When the voltage descends below 3V, the assembly module PCB is normal and the main PCB is poor. Then replace the main PCB. 3. Replace the assembly display PCB because the module PCB is poor if the voltage between No. 7~5 of CN91 maintains 5V after the remote control starts operation. Samsung Electronics Samsung Electronics...
2) The fan motor of the indoor unit doesn’t run. • Fan Motor Connector(CN72) is faulty 3) The power voltage between terminal #3 and #5 • ASS’Y Main PCB is faulty of the connector(CN72) is 0V. • Connection is faulty 4-10 Samsung Electronics...
∞, 0Ω . . . Open or Short Stepping Motor Measure the resistance between the red wire and each terminal wire with a tester. Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) Abnormal ∞, 0Ω . . . Open or Short Samsung Electronics 4-11...
5. PCB Diagram and Parts List 5-1. Block Diagram 5-1-1. Ass'y Control In This document can not be used without Samsung's authorization. Samsung Electronics...
#4:Motor driving signal #7:Vovt output_3 #8:PWM_LED #5:Motor driving signal #9: ROM-TEMP output_4 ⑨CN81-MPI #1:MPI driving signal output (-) #2:MPI driving signal output (+) #3:DV12V #4:MPI feedback signal input This document can not be used without Samsung's authorization. Samsung Electronics...
5-1-3. Indoor Display PCB #1: DIO #2: CLK #3: STB #4: IRQ #5: GND #6: Vcc #7: Vout #9: NTC01 This document can not be used without Samsung's authorization. Samsung Electronics...
7.Schematic Diagram 7-1.PCB Circuit Description 7-1-1.Indoor Unit This document can not be used without Samsung's authorization. Samsung Electronics...
Page 40
7-1.PCB Circuit Description 7-1-2.Display This document can not be used without Samsung's authorization. Samsung Electronics Samsung Electronics...
8-1 Refrigerating Cycle Diagram Outdoor Unit Indoor Unit ※Note Capillary tube Check valve 2 way valve Liquid side Capillary tube Heat Heat Exchanger Exchanger (Evaporator) (Condenser) Gas side 3 way valve 4 way valve Cooling Heating Compressor Gas Leak Check Point Samsung Electronics...
183kgf•cm with a torque wrench. (gas) (liquid) 7) Check for gas leakage. - At this time, especially check for gas leakage from the 3 way valve’s stem nuts, and from the service port cap. Samsung Electronics...
Page 46
• Make sure you do not bend the connection pipes in the middle and store together with the cables. • Move the indoor and outdoor units to a new location. • Remove the mounting plate for the indoor unit and move it to a new location. Samsung Electronics...