Related Manuals for Makita DGA504RTE
Summary of Contents for Makita DGA504RTE
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder DGA404 DGA454 DGA504 015078 IMPORTANT: Read Before Using.
- Page 2 ENGLISH (Original instructions) SPECIFICATIONS Model DGA404 DGA454 DGA504 Wheel diameter 100 mm (4") 115 mm (4-1/2") 125 mm (5") Max. wheel thickness 6.4 mm (1/4") 6.4 mm (1/4") 6.4 mm (1/4") Spindle thread M14 or 5/8" (country specific) Rated speed (n) / No load speed (n 8,500 min With battery cartridge BL1815N, 348 mm...
- Page 3 Uncertainty (K) : 1.5 m/s 000331 Yasushi Fukaya Work mode : surface grinding with anti vibration Director side grip Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium Vibration emission (a ) : 6.0 m/s h,AG Uncertainty (K) : 1.5 m/s GEA006-2 Work mode: disc sanding...
- Page 4 of electric shock. operate the power tool. Power tools are If operating a power tool in a damp location is dangerous in the hands of untrained users. unavoidable, use a ground fault circuit 21. Maintain power tools. Check for misalignment interrupter (GFCI) protected supply.
- Page 5 specifications provided with this power tool. Failure Keep bystanders a safe distance away from to follow all instructions listed below may result in work area. Anyone entering the work area electric shock, fire and/or serious injury. must wear personal protective equipment. Operations such polishing...
- Page 6 b) Never place your hand near the rotating b) Do not position your body in line with and accessory. Accessory may kickback over your hand. behind the rotating wheel. When the wheel, at c) Do not position your body in the area where the point of operation, is moving away from your power tool will move if kickback occurs.
- Page 7 ENC007-9 in wheel breakage. 19. Make sure the wheel is not contacting the IMPORTANT SAFETY workpiece before the switch is turned on. INSTRUCTIONS 20. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or FOR BATTERY CARTRIDGE wobbling that could indicate poor installation or a poorly balanced wheel.
- Page 8 FUNCTIONAL DESCRIPTION 1. Slide switch CAUTION: Always be sure that the tool is switched off and the • battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 015082 1. Button To start the tool, slide the slide switch toward the "I 2.
- Page 9 Automatic speed change function Indicator lamps Remaining 1. Mode indicator capacity Lighted Blinking 75% to 100% 50% to 75% 25% to 50% 015142 0% to 25% Charge the battery. Mode indicator status Operation mode The battery may have High speed mode malfunctioned.
- Page 10 Releasing protection lock Installing or removing wheel guard When the protection system works repeatedly, the tool is (For depressed center wheel, multi disc / locked and the battery indicator shows the following state. abrasive cut-off wheel, diamond wheel) WARNING: Battery indicator Blinking When using...
- Page 11 Installing or removing depressed center 012772 wheel or flap disc (optional accessory) Mount inner flange, abrasive wheel and Ezynut onto the spindle so that Makita Logo on Ezynut faces outside. WARNING: 1. Shaft lock When using a depressed center wheel or flap disc, •...
- Page 12 NOTE: OPERATION Ezynut can be loosened by hand as long as the • arrow points the notch. Otherwise a lock nut WARNING: wrench is required to loosen it. Insert one pin of It should never be necessary to force the tool. The •...
- Page 13 Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel/diamond wheel 010855 Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Mount the inner flange and abrasive cut-off / diamond wheel onto the spindle.
- Page 14 WARNING: Operation with wire wheel brush When using an abrasive cut-off / diamond wheel, (optional accessory) • be sure to use only the special wheel guard designed for use with cut-off wheels. (In some CAUTION: European countries, when using a diamond wheel, Check operation of wire wheel brush by running •...
- Page 15 Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Makita genuine battery and charger •...
- Page 16 100 mm (4") model 115 mm (4-1/2") model 125 mm (5") model Grip 36 Wheel Guard (for grinding wheel) Inner flange 42 Inner flange 42 Inner flange 30 Super flange 47 *1 Super flange 47 *1 Depressed center wheel/Flap disc Lock nut 14-45 Lock nut 14-45 Lock nut 10-30...
- Page 20 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com 885376D220...