Table of Contents
Advertisement
Quick Links
Z Master
With 48in, 52in, or 60in TURBO FORCE
Model No. 77281—Serial No. 400000000 and Up
Model No. 77281TA—Serial No. 400000000 and Up
Model No. 77283—Serial No. 400000000 and Up
Model No. 77285—Serial No. 400000000 and Up
Model No. 77288—Serial No. 400000000 and Up
Model No. 77291—Serial No. 400000000 and Up
Model No. 77291TA—Serial No. 400000000 and Up
Model No. 77294—Serial No. 400000000 and Up
Model No. 77294TA—Serial No. 400000000 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
2000 Series Riding Mower
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No. 2 lithium or molybdenum grease
(purchase separately)
No parts required
No parts required
Register at www.Toro.com.
Form No. 3456-100 Rev A
®
Mower
Qty.
–
Remove the machine from the crate.
–
Add fuel to the machine.
–
Check the engine-oil level.
–
Check the tire pressure.
–
Servicing the battery.
–
Raise the roll bar.
–
Check the grass deflector.
Remove the shipping cable ties
–
(MyRide™ suspension system only).
1 tube
Check the machine for grease.
–
Check the mower adjustment.
Check the machine before delivery to
–
the customer (all machines).
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Setup Instructions
Use
*3456-100*
Advertisement
Table of Contents
Related Manuals for Toro 77281TA
Summary of Contents for Toro 77281TA
- Page 1 With 48in, 52in, or 60in TURBO FORCE ® Mower Model No. 77281—Serial No. 400000000 and Up Model No. 77281TA—Serial No. 400000000 and Up Model No. 77283—Serial No. 400000000 and Up Model No. 77285—Serial No. 400000000 and Up Model No. 77288—Serial No. 400000000 and Up Model No.
-
Page 2: Removing The Machine From The Crate
Procedure Description Qty. Operator's Manual Engine owner's manual (non-Toro engines) Deliver the machine to the customer. Operator training material Registration card Note: Determine the left and right sides of the machine from the normal operating position. Removing the Machine Checking the Engine-Oil... -
Page 3: Servicing The Battery
Servicing the Battery Raising the Roll Bar No Parts Required No Parts Required Procedure Procedure Important: Important: Do not run the machine with the Always use the seat belt with the roll battery disconnected; electrical damage may bar in the raised position. occur to the engine. - Page 4 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. g021181 WARNING Figure 3 An uncovered discharge opening could allow 1. Grass deflector 3. End of spring the machine to throw objects toward you or 2.
- Page 5 Removing the Shipping Cable Ties MyRide™ Suspension System Only No Parts Required Procedure Note: This procedure is for machines with a MyRide™ suspension system only. CAUTION The springs are compressed by the shipping cable ties. When you remove the cable ties, the seat and springs will raise up quickly by g412478 Figure 4...
-
Page 6: Checking The Mower Adjustment
Checking the Mower Adjustment No Parts Required Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as needed. Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure... - Page 7 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine owner's manual (non-Toro engines) Operator training material Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
- Page 8 Ensure that the customer receives the Operator's Manual, engine owner's manual (non-Toro engines), Setup Instructions, and operator training material. Ensure that the customer knows that the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.