Table of Contents
Advertisement
Quick Links
Basket Kit
27-inch DPA Reel Mower for Reelmaster
Unit
Model No. 03185
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
© 2016- The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
(right)
(left)
Flange nut (5/16 inch)
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
-
1
2
1
1
2
2
4
4
1
1
2
2
1
4
4
-
2
-
3
Form No. 3377-292 Rev D
®
3100-D Series Traction
Installation Instructions
Use
Prepare the machine.
Mount the roller bumper.
Mount the hydro guard.
Install the basket mounting assemblies.
Install the cut-off bar.
Install the new grass deflector.
Remove the support tube.
Assemble the rear grass basket.
Mount the baskets to the cutting units.
Original Instructions (EN)
All Rights Reserved *3377-292* D
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 03185
Summary of Contents for Toro 03185
-
Page 1: Table Of Contents
– No parts required Assemble the rear grass basket. Basket Mount the baskets to the cutting units. © 2016— The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3377-292* D 8111 Lyndale Avenue South Printed in the USA... -
Page 2: Description
Note: The 27 inch rear roller brush kit (Model 03186), will not work with the rear grass basket on the Reelmaster 3100 Grass Basket Kit (Model 03185). The rear cutting unit can be fitted with the Rear Roller Scraper Kit (Part No. 114-9368) in place of the rear roller brush kit. -
Page 3: Guide Assembly
Installing the Basket Mounting Assemblies Parts needed for this procedure: Guide assembly Bracket assembly Carriage bolt (5/16 x 1 inch) Flange nut (5/16 inch) Basket bracket with guide assembly (right) g026365 Basket bracket with bracket assembly (left) Figure 2 Bolt (5/16 x 2-1/4 inch) 1. - Page 4 Note: The carriage bolts and flange bolts are shipped Note: The bolt must be threaded through the far wall installed on the guide assembly. of the tube. Rear Cutting Unit 7. Insert the left basket bracket with bracket assembly onto the left end of the cutting unit carrier frame tube Important: Use the red colored rear stop-basket (Figure when operating in rugged terrain to help retain...
-
Page 5: Cut-Off Bar
g012217 Figure 5 1. Bolt (5/16 x 2-1/4 inch) 3. Flange nut (5/16 inch) 5. Left basket bracket with bracket 2. Right basket bracket with guide 4. Carrier frame Installing the Cut-off Bar Parts needed for this procedure: Cut-off bar Bolt (1/4 x 1-3/4 inches) Locknut (1/4 inch) g012218... -
Page 6: No Parts Required
Installing the New Grass Deflector (Front Cutting Units Only) No Parts Required Procedure g012219 1. Remove the 2 center deflectors and the deflector from Figure 7 each end of the shield, leaving only the 2 shown in 1. Cut-off bar 3. -
Page 7: Flange Locknut (3/8 Inch)
3. Install the grass shield and remaining deflectors. 2. Using the cable ties on straps as handles, stretch each strap until it can be secured to top of basket with 2 washers and a locknut (Figure 12). Position a washer on each side of the basket top. -
Page 8: Basket
• Position the basket so it is parallel to the cutting unit with a minimum clearance of 6 mm (0.250 inch) between the lip of the basket and the reel (Figure 15). • On each end of the basket, adjust the basket stop brackets Mounting the Baskets to the so they each contact a side plate. - Page 9 Adjusting the Rear Basket Lip Bracket No Parts Required Procedure Check to make sure that the top of the rear basket lip bracket is flush to 6 mm (0.250 inches) with the roller (Figure 18). If the bracket is not flush with the roller, loosen the mounting g195002 cap screws and adjust the bracket as required.
- Page 10 Adjusting the Roller Bumper No Parts Required Procedure Adjust the roller bumper (Figure 19) so that the roller is parallel with the top shield on center basket on contact. If the basket is not parallel, the rear of the basket may contact the engine when it is raised.
- Page 11 Notes:...