GE CVM1790SSSS Installation Instructions Manual
Above the cooktop oven
Hide thumbs
Also See for CVM1790SSSS:
- Dimensions and installation information (3 pages) ,
- Owner's manual (76 pages)
Related Manuals for GE CVM1790SSSS
Summary of Contents for GE CVM1790SSSS
- Page 3 Ensure proper ground exists before use...
- Page 4 DUCT PIECES Roof Cap 12 Ft. Straight Duct (6 Round) Rectangular-to-Round Transition Adaptor* Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. DUCT PIECES Wall Cap 3 Ft. Straight Duct ⁄...
- Page 5 DUCT PIECES Rectangular-to-Round Transition Adaptor* Wall Cap 90° Elbow 45° Elbow 90° Elbow 45° Elbow Roof Cap Straight Duct 6 Round or ⁄ x 10 Rectangular EQUIVALENT NUMBER LENGTH USED 5 Ft. 40 Ft. 10 Ft. 5 Ft. 25 Ft. 5 Ft.
- Page 6 PART Wood Screws ⁄ x 2 ) Toggle Bolts (and wing nuts) ( ⁄ x 3 ) Self-aligning Machine Screw ( ⁄ -28 x 2 ⁄ Nylon Grommet (for metal cabinets) Metal Screws ⁄ ⁄ PART QUANTITY 1 black 2 bronze QUANTITY Top Cabinet Template...
- Page 7 # 1 and #2 Phillips screwdriver Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Gloves Saw (saber, hole or keyhole) Safety goggles 13 max. ⁄ 66 or more from the floor to the top of the oven Ruler or tape measure and straight edge...
- Page 8 Wall Studs Center Carton Styrofoam...
- Page 9 Mounting Plate Tabs Touching the Cabinet Bottom Mounting Plate with Tabs Below Cabinet Bottom the Same Distance as the Front Overhang Depth 30 to Cooktop Mounting Plate Tabs Touching the Back Frame 30 to Cooktop...
- Page 10 Hole B Draw a Vertical Hole A Line on Wall from Center of Top Cabinet Hole D Hole C Area E...
- Page 11 Adaptor in Place for Outside Top Exhaust...
- Page 12 Spacing for Toggles More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End...
- Page 13 Damper Exhaust Adaptor Blower Plate Back of Oven...
- Page 14 Cabinet Front Cabinet Bottom Shelf Filler Block Self-Aligning Screw Oven Top This distance can NOT Equivalent exceed 2” to to Depth of ensure proper Cabinet Recess installation Damper Back of Oven House Duct...
- Page 16 Spacing for Toggles More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End Retaining Flange Blower Motor Screw End A Before Rotation Back of Oven Before Rerouting Wires Routed Through Left Side Wires Routed Through Right Side Blower Plate End B After Rotation...
- Page 17 Before Rolling After Rolling Back of Oven End B Back of Oven Snip all 4 webs Exhaust Adaptor on each knockout panel and remove the metal knockouts for rear airflow. Slide exhaust adaptor into guides on oven rear. End A Blower Plate Screws Blower Plate Back of Oven...
- Page 18 Cabinet Front Cabinet Bottom Shelf Filler Block Self-Aligning Screw Oven Top This distance can NOT Equivalent exceed 2” to to Depth of ensure proper Cabinet Recess installation...
- Page 19 Spacing for Toggles More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End...
- Page 20 Blower Plate Screws Back of Oven Retaining Flange Blower Motor Screw Blower Plate Roll...
- Page 21 Blower Plate Screws Back of Oven Blower Motor Screw...
- Page 22 Cabinet Front Cabinet Bottom Shelf Filler Block Self-Aligning Screw Oven Top This distance can NOT Equivalent exceed 2” to to Depth of ensure proper Cabinet Recess installation Screws Grille Charcoal filter Charcoal filter installed Front lower tabs...
- Page 23 Ensure proper ground exists before use.
- Page 30 ≤ ≤ ≤...