Page 1
: The metallic dust filter is used. Multi Functional Cleaning System AS09BPAN, AS12BPAN AS09BPAN/XSA, AS12BPAN/XSA : The anti allergy filter and activated deodorizing filter are adopted. Human Touch Remote control AS09BPAX, AS12BPAX AS09BPAX/XSA, AS12BPAX/XSA For more information, Please access to our service web site (http://itself.sec.samsung.co.kr)
All manuals and user guides at all-guides.com Contents 11. Precautions ..................................................1-1 Installing the air conditioner ....................1-2 Power supply and circuit breaker ..........................1-3 During operation ........................1-4 Disposing of the unit ..............................1-5 Others 12. Product Specifications ......................
Page 3
All manuals and user guides at all-guides.com Contents 19. Circuit Descriptions ..............................................9-1 PCB Circuit Descriptions ......................9-2 Refrigerating Cycle Diagram 10. PCB Diagram 10-1 ....................................................... 10-1 Indoor PCB 10-1 ............................. 10-2 Outdoor PCB 10-2 11. Operating Instruction and Installation 11-1 ................
Do not place a cloth or other materials over it. G Remove the batteries if you don’t use the remote control for a long time. (If applicable) G Use the remote control within 7 meters from the indoor unit. (If applicable) Samsung Electronics...
G Young children or infirm persons should be always supervised when they use the air conditioner. G Max current is measured according to IEC standard for safety. G Current is measured according to ISO standard for energy efficiency. Samsung Electronics...
With an anti-allergy filter and activated deodorizing filter, it removes an allergy antigen as well as a tobacco odor. I Human touch remote control The use of air conditioner is easier and more convenient by the human touch remote control of new design. Samsung Electronics...
• If you want to turn on/off the Display during operation, press the button on the remote control. • The room temperature sensor senses air temperature around the sensor, and shows the temperature on the display. Samsung Electronics...
Page 8
All manuals and user guides at all-guides.com Product Specifications 2-2-2 Outdoor Unit Air Inlet(Rear) Air Outlet Connection Valve (inside) Samsung Electronics...
All manuals and user guides at all-guides.com 2-4 The Comparative Specifications of Product Item AS09BPA AS09HPB Indoor Unit Design Outdoor Unit Indoor Unit 9.0kg 9.0kg Net Weight Outdoor Unit 40.0kg 33.8kg Indoor Unit 950x268x165mm 950x268x165mm Outer Dimension (WidthxHeightxDepth) Outdoor Unit...
Page 11
Outdoor Unit 53dB↓ 53dB↓ Silver Nano Metallic Filter Silver Nano Metallic Filter Air Purifying System Filter Anti-Allergy Filter Anti-Allergy Filter Deodorizing Filter Deodorizing Filter Detachable Display Detachable Display Indoor Display Rotation Blue LED Display Rotation Blue LED Display Samsung Electronics...
In-coil sensor Error Open/Short Indoor Fan Motor Abnormal Operation FAN Error Holding for 15 sec. at less than 450rpm 1min. Time out Communication All Lamps Blink EEPROM Error All Lamps Blink Option Error Option Not Set up, Option Data Error Samsung Electronics...
I_Trip error / PFC Over current GAS Leak error(Dual/Single) AC Line Zero Cross Signal out Power ON reset(1sec) Capacity miss match Test Operation at Cooling Mode Test Operation at Heating Mode : LED ON, : LED OFF, : LED BLINK Samsung Electronics...
✳ Setting is not required if you must Push the button to set the display panel to Every time you push the button, the display panel reads a value which has a default..repeatedly. Samsung Electronics...
Page 17
If all lamps of indoor unit are flickering, plug out, plug in power plug again and press the ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics...
3) Loosen 1 of the right screw and detach the Ass'y display. 4) Loosen 1 of the right screw and detach the Terminal Cover. 5) Detach the cover PCB-DVM and thermis- tor from the Panel Front. Samsung Electronics...
Page 20
8) Unlock 2 hooks to fix Panel Front and Back Body. Tray Drain 1) Detach the connected wire of Stepping Motor. 2) Pull Tray Drain out from the Back Body. 1) Loosen 1 fixing earth screw of right side. Heat Exchanger Samsung Electronics...
Page 21
3) Detach the Holder Pipe at the rear side of the unit. 4) Loosen 3 fixing screws of left Holder Evap. 5) Loosen 1 fixing screw of right Holder Motor. 6) Detach the Heat Exchanger from the indoor unit. Samsung Electronics...
Page 22
1) Loosen 2 fixing screws and detach the & Motor Holder. 2) Loosen 1 fixing screw of Fan Motor. Cross Fan 3) Detach the Fan Motor from the Fan. 4) Detach the Fan from the left Holder Bearing. Samsung Electronics...
Cabinet Front lower to detach the Cabinet Front. 3) Detach the Cabinet Front like the picture on the right side. 4) Loosen 1 screw fixed to assemble Plate Control Out with Cabinet-Side RH. Samsung Electronics...
Page 24
Disassembly and Reassembly Parts Procedure Remark 5) Loosen 2 fixing screws on the rear side of Cabinet-Side RH. 6) Loosen 3 screws fixed to assemble Bracket Valve with Cabinet-Side RH. 7) Loosen 2 fixing screws of Cabinet-Side LF. Samsung Electronics...
Page 25
1) Detach the Motor Wire from the PCB of Ass'y Control Out. 2) Detach several connectors from the PCB of Ass'y Control Out. 3) Detach 2 Connect Wires from Reactor. 4) Loosen 1 screw fixed to assemble Ass'y Control Out with Partition. Samsung Electronics...
Page 26
1) Loosen the Nut of Terminal Cover. Compressor 2) Detach the Terminal Cover and detach the Connect Comp Wire from Compressor. 3) Disassemble the Felt Comp Sound. 4) Loosen the 3 bolts at the bottom of Compressor like the picture on the right side. Samsung Electronics...
All manuals and user guides at all-guides.com 5. Exploded Views and Parts List 5-1 Indoor Unit 14-1 14-2 14-3 14-4 14-5 23-1 14-6 23-2 2-5-1 Samsung Electronics...
Page 28
BUSH BODY RH HIPS 14-4 DB63-01105A COVER-IONIZER HIPS 14-5 DB91-00287A ASS'Y ELECTRIC-IONIZER ASS'Y 14-6 DB93-01383G ASS'Y C/W ION ASS'Y DB61-02051A HOLDER-PIPE HIPS DB67-00508A CAP SCREW HIPS DB70-00514A PLATE-HANGER SGCC-M, T0.8 DB70-00515A PLATE CONTACT SUS 304 DB70-00516A PLATE-CONTROL IN SGCC-M Samsung Electronics...
All manuals and user guides at all-guides.com 7. Wiring Diagram 7-1 Indoor Unit This Document can not be used without Samsung's authorization. Samsung Electronics...
All manuals and user guides at all-guides.com 8. Schematic Diagram 8-1 Indoor Unit This Document can not be used without Samsung's authorization. Samsung Electronics...
9. Circuit Descriptions 9-1 PCB Circuit Descriptions 9-1-1 Indoor Unit SMPS BUZZER PART INDOOR FAN CONTROL SUB PCB CONNECTOR ZERO CROSSING PART DISPLAY INDOOR TEMPERATURE SENSOR STEP MOTOR & ION This Document can not be used without Samsung's authorization. Samsung Electronics...
Page 50
All manuals and user guides at all-guides.com 1/16/05 9:59 PM Page 3-38 Circuit Descriptions Circuit Descriptions 9-1-2 Outdoor Unit TEMPERATURE SENSOR & EEV BLDC FAN COMMUNICATION SMPS INVERTER This Document can not be used without Samsung's authorization. Samsung Electronics...
9-2 Refrigerating Cycle Diagram Outdoor Unit Indoor Unit 2-Way Service Valve(1/4") Liquid Side Expansion Valve Capillary Tube Heat Exchanger Heat (Evaporator) Exchanger (Condenser) Cross Fan Gas Side 4-Way 3-Way Valve Service Valve(3/8") Cooling Compressor Heating Gas Leak Check Polnt Samsung Electronics...
& Power Temperature Sensor Motor RPM Feedback BLADE-H Step Motor Remocon Module HVPS(High voltage Generator) Humidity Sensor DISPLAY PCB Connection Anions Melody PCB Connection Auto grill 1 Test Board Connection & Auto grill 2 Indoor Fan Motor Samsung Electronics 10-1...
All manuals and user guides at all-guides.com 10-2 Outdoor PCB ! @ ) & Power Comp./Cond. Temperature Sensor & Power L Outdoor/Discharge Temperature Sensor BLDC FAN EEV Connector Communication N Comp. Connector Wire Communication Reactor Connector Wire 10-2 Samsung Electronics...
Automatic (rotated : Medium High Heat Mode Press the button on the remote control until is displayed. Press the button to select the fan speed until the required setting is displayed. Automatic (rotated : Medium High Samsung Electronics 11-1...
Page 55
All manuals and user guides at all-guides.com Operating Instruction and Installation Basic Function(cont.) Mode Explanation Remark Dry Mode Press the button on the remote control until is displayed. Fan Mode Press the button on the remote control until is displayed. 11-2 Samsung Electronics...
Page 56
Function Anions Function Press the button. • If you press the button when the air conditioner is off, the air conditioner turns on automatically and generates anions in the Fan mode with Low fan speed. Samsung Electronics 11-3...
[In case of heat pump model] exterior ice in a HEAT mode, and indoor fan and outdoor Indoor fan and outdoor fan stop operation intermittently in a HEAT mode. fan do not operate intermittently for within 20% of the total heater operation Samsung Electronics 12-1...
Replace fuse FUSE(F701) : T3.15[A]/250[V] Check the output of SMPS on the control board. Input power: AC230±15%[V] PCB should be replaced IC02 Input: DC12[V] IC02 output: DC5[V] N Check the setting temperature 12-2 Samsung Electronics...
Page 60
PCB? Disassemble the BLDC FAN Wire. Exchange the PCB. Are the BLDC FAN Wire Is the +, - of C102 short? 1 and 3 short? Exchange the PCB. Exchange the BLDC FAN. Normal Operation Exit Samsung Electronics 12-3...
Page 61
Normal of the remote control unit pushed? Voltage at pin #30~#34 of micom(IC04) Micom(IC04) is faulty. change?(Squarewave) Voltage at pin #2~#5 of CN61(motor connector) Driver IC05/06(ULN2003A) is faulty. change?(Squarewave) Up/Down louver motor is faulty. 12-4 Samsung Electronics...
Page 62
Pull out the power cord and during the operation?(Square-Wave) execute the following step after 30 seconds. Disassemble the BLDC FAN Wire. Is the short between Exchange the PCB. the BLDC FAN Wires? Exchange the BLDC FAN MOTOR. Exchange the PCB. Samsung Electronics 12-5...
Page 63
Pull out the power cord and exchange the PCB from the case after 30 seconds. Is the assembly of Micom and Exchange the PCB. peripheral circuit part good? Check again after assembly of PCB. 12-6 12-5 Samsung Electronics...
Page 64
4-WAY valve coil error of 4-WAY valve coil. Dose the voltage of AC 220V Exchange apply to the connector of 4-WAY the outdoor PCB. valve coil during the operation? Go to the next page 4-WAY valve main body error Samsung Electronics 12-7...
Page 65
Connect the connector. correctly? Check the resistance value Outdoor fan error of outdoor fan. Dose the voltage of DC300V apply to the connector of outdoor Check the motor wire. fan during the operation of outdoor unit? Outdoor PCB error 12-8 Samsung Electronics...
Page 66
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 18.2K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 Samsung Electronics 12-9...
Page 67
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 24K? Exchange the PCB. Exchange the PCB. Normal operation Exit 600.0 500.0 400.0 300.0 200.0 100.0 12-10 Samsung Electronics...
Page 68
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 24K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 Samsung Electronics 12-11...
Page 69
4) Is the resistance value of sensor connection pull_up correct? 2. Troubleshooting procedure Isn't the Fan locked? Remove the Fan lock. Is the connector connected correctly? Connect the connector. Is the color of Fan wire matched correctly? Exchange the Fan. Exchange the PCB. Normal operation Exit 12-12 Samsung Electronics...
Page 70
Is the capacitor(C101,C102,C103) for DC-Link assembled in accordance Exchange the PCB. the specification? Are R113, R114, R115 470kohm? Exchange the PCB. Is R116 14.3kohm? Exchange the PCB. Exchange the PCB. Normal operation Exit Samsung Electronics 12-13...
Page 71
Is the position of temperature sensor Correct the sensor position or and the sensing value normal? exchange the sensor. Is the connection cable for Correct the cable connection. the compressor and power terminal normal? Exchange the PCB. 12-14 Samsung Electronics...
Page 72
Correct the wrong wiring. and communication cable error? Correct the connection of Is the connection of communication cable normal? communication cable. Is it the outdoor Exchange the indoor/outdoor unit PCB. 2 Micom(Inverter + Main) model? Exchange the outdoor unit PCB. Samsung Electronics 12-15...
Page 73
Is the interphase resistance value of Exchange the compressor. compressor(u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. 12-16 Samsung Electronics...
Page 74
Is the interphase resistance value of Exchange the compressor. compressor(u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. Samsung Electronics 12-17...
Page 75
Is the resistance for the Exchange the PCB. detection of DC Link voltage normal? Is the resistance value of Exchange the PCB. DC Link discharge normal? Is the reactor insulation damaged? Exchange the PCB. Exchange the reactor. 12-18 Samsung Electronics...
Page 76
12-2-18 The others 1. AC Line Zero Cross Signal OUT – Check the assembly condition of peripheral part of IC21, ZD201, ZD200 and D200 on the PCB. 2. Capacity miss match – Check again the indoor unit option code. Samsung Electronics 12-19...
2) The fan motor of the indoor unit doesn't run. • Fan Motor Connector(CN72) is faulty 3) The power voltage between terminal #3 and #5 • ASS'Y Main PCB is faulty of the connector(CN72) is 0V. • Connection is faulty 12-20 Samsung Electronics...
Page 78
1) Is CN01 1, 3 over 250V? • Outdoor PCB Error 2) Is CN01 3, 5 within 1V~5V? • BLDC Motor Error 3) Is the voltage of CN01 6 changed? 4) Is the resistance of BLDC Motor 1, 3 opened after power off? Samsung Electronics 12-21...
∞, 0Ω . . . Open or Short Abnormal Measure the resistance between the red wire and each terminal wire with a tester. Stepping Motor Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) ∞, 0Ω . . . Open or Short Abnormal 12-22 Samsung Electronics...
Page 80
All manuals and user guides at all-guides.com MEMO Samsung Electronics 12-23...
SELECT/CANCEL STEPPING MOTOR TEMPERATURE : BLADE CONTROL SELECT(UP/DOWN) MELODY CONTROL PART SLEEP OPERATION DC5V VOLTAGE REGULATOR ANION SELECT SPEAKER AUTO CLEAN SELECT OPTION ENERGY SAVING SELECT DC12V SMPS POWER BLOCK SOUND ON/OFF SELECT DIGITAL ON/OFF AC INPUT 13-1 Samsung Electronics...
Page 82
All manuals and user guides at all-guides.com Block Diagram INDOOR FAN CONTROL SMPS AC COMMUNICATION SUB-PCB BUZZER CONTROL Samsung Electronics 13-2...
• FAN CONTROL SIGNAL • EEV CONTROL SIGNAL • 4-WAY CONTROL SIGNAL • PFC CONTROL SIGNAL COMPRESSOR • COMPRESSOR CONTROL(6P,BLDC) • LED CONTROL SIGNAL • INDOOR COMMUNICATION SIGNAL • 4-WAY VALVE • EEV SMPS INDOOR UNIT PFC CIRCUIT AC INPUT 13-3 Samsung Electronics...
Page 84
All manuals and user guides at all-guides.com Block Diagram OUTDOOR FAN IGBT DIODE DC_LINK CAP SMPS Samsung Electronics 13-4...
Window type 220V/60Hz/3 phase None SET Normal P HB(For Western) 380V/50Hz/3 phase Split type Indoor Unit Tropical M HB(For others) Outdoor Unit R410 1 Option Inverter(R22) Inverter(R410) • Except the window type for USA & Models for China 14-1 Samsung Electronics...
It occurs when the drain pump is plugged out or it is out of order. Check the power of the drain pump and the position of the drain hose, and when the pump is faulty, contact the drain pump manufacturer. Samsung Electronics do not manufacture drain pumps. So, we are not able to correct the drain pump problems.
Page 88
Set up a sun blind over the outdoor unit and clear the neighboring obstacles from the outdoor unit to provide good ventilation. When it goes off frequently during a heat wave, it would prevent the turn-off and increase the cooling capacity cleaning the outdoor unit or spraying some water to the heat exchanger. Samsung Electronics 14-4...
Page 89
There is a cost table. But, our service engineer needs to visit to total up the cost correctly. When you move in, make sure to contact Samsung Electronics Service Center or Authorized Service Agent in advance to streamline the process.
7. Reassemble the air filter and the front grille. Body Hook Front grille Note : • If you have not used the air conditioner for a long time, select the Fan mode for 3 to 4 hours to dry the inside of the air conditioner. Samsung Electronics 14-6...
Page 91
2. Pull out the Anti-Allergy and Deodorizing filter. 3. Wash the filters with clean water, then dry them in the shade. Deodorizing Filter Anti-Allergy Filter 4. Insert the filters in their place. 5. Close the front grille. 14-7 Samsung Electronics...
Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the Electric Business Laws. I Inspection & Trial Run Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to finish the installation. Samsung Electronics 14-8...
Stem cap 183kgf . cm with a torque wrench. (gas) (liquid) 7) Check for gas leakage. - At this time, especially check for gas leakage from the 3-Way valve’s stem nuts, and from the service port cap. 14-9 Samsung Electronics...
Page 94
• Make sure you do not bend the connection pipes in the middle and store together with the cables. • Move the indoor and outdoor units to a new location. • Remove the mounting plate for the indoor unit and move it to a new location. Samsung Electronics 14-10...
Page 95
All manuals and user guides at all-guides.com MEMO 14-11 Samsung Electronics...