Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
3.2 Assembly/Panel Removal 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand 2. Take the stand bracket out from the set.
Page 10
3.2.2 IR board Control Unit 1. Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! 1. Remove all the fixation screws [1] and connector from the IR board control unit. 3. Remove the IR lens, IR board from the DECO_REAR_COVER. When defective, replace the whole unit.
Page 11
3.2.3 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1. Remove fixation screws [2] and [3] that secure the base assy.. 2. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set. ( 6482 series) (7502 series)
Page 12
3.2.4 Keyboard Control Unit Release the connector from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! Remove all the fixation screws from the keyboard control panel [1] and take it out from the Back cover When defective, replace the whole unit.
Page 13
(55" 9002 series) 3.2.5 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. 1. Release the clips from the LVDS connector that connect with the SSB[1]. Caution: be careful, as these are very fragile connectors! 2.
Page 14
3. Remove all fixation screws from the PSU. 3. The PSU can be taken out of the set now. 3.2.7 Speakers 1. Gently release the tapes that secure the speaker cables. 2. Unplug the speaker connector from the SSB. 3. Take the speakers out. When defective, replace the both units.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 16
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 17
Public Broadcasting Service password Reset. etc. How to Activate the Factory mode To activate the Factory mode, use the following method: Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return”...
Page 18
Line number for every line (to make CSM language independent). Set the screen mode to full screen (all contents on screen is visible). After leaving the Customer Service Mode, the original settings are restored. Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC. How to Activate CSM To activate CSM, press the following key sequence on a standard remote control transmitter: “123654”...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading Step 1: Ready for F/W Upgrade 1. Rename the software as “autorun.upg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). Note the version of this F/W before you change the software file name. Step 2: F/W Upgrade 1.
Page 20
4. Press OK to start software upgrade 5. Upgrade in progress...
Page 21
Step 3: Check the SW version 1. After burning software, TV will restart 2. Press “Menu+1999+back”, enter Factory mode to check if the software version is correct Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 22
5.2.3 Error codes overview In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking when CSM is activated. Only the following layer 2 errors are defined: 5.2.4 How to Clear the Error Buffer The error code buffer is cleared in the following cases: •...
Page 23
“Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT Panel Type Display Code Setting Set Option Code BOM# 43PUS6412/12 TPT430U3-EQYSHM.G S1T 49PUS6412/12 TPT490U2-EQYSHM.G SC1T 49PUS6482/12 TPT490U2-EQYSHM.G SC1S 49PUS7002/62 TPT490U2-EQYSHM.G SC1S...
6. Circuit Descriptions 6.1 Introduction The TPM17.1E LA is a new chassis launched in EU in 2017. The whole range is covered by MT5596UGIJ+ NT72333/NT72334 platform. The major deltas versus its predecessor support DVB-C, DVB-T, DVB-T2, DVB-S, DVB-S2 with also USB3.0,WIFI/multi-media, Video out The TPM17.1E LA LA chassis comes with the following stylings: series xxPUS64x2/xx ...
Page 25
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 26
- side-view LED without scanning: PSL power panel - side-view LED with scanning: PSLS power panel - direct-view LED without 2D-dimming: PSL power panel - direct-view LED with 2D-dimming: PSDL power panel. PSL stands for Power Supply with integrated LED-drivers. PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller).
Page 27
6.3.2 Power layout SSB L4304 +3.5V_SB C4457 +12V AMBI C777 TUNER LNB C4309 +3.3V STANDBY L4101 +2.5V NT C4344 +1.8V EMMC-IO CM47 +1.5V DDR Power SSB Top View...
Page 29
6.4 Front-End Analogue and DVB-T, DVB-C, DVB-S;ISDB-T reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER EUROPE TDSY-G480D • TUNER EUROPE TDQS-A701F • SCALER MT5596UGIJ HSFBGA-899 Below find a block diagram of the front-end application for DVB-C part. 6.4.2 DTB-T/T2 part The Front-End for DVT part consist of the following key components: •...
Page 30
6.4.3 DTB-S2 part The Front-End for DVT part consist of the following key components: • TUNER EUROPE TDSY-G480D • TUNER EUROPE TDQS-A701F • SCALER MT5596UGIJ HSFBGA-899 • DEMODULATOR Si2169-C60-GMR QFN-48 Below find a block diagram of the front-end application for DTV part. 6.5 HDMI Refer to below for the application.
Page 31
The following HDMI connector can be used: • HDMI 1: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC • HDMI 2: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC • HDMI 3: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC •...
8.9 E 715G8555 Keyboard control panel 8-9-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY 1 AMBI_SPI_CLK Left...
8.10 E 715G7088 Keyboard control panel 8-10-1 Key CONN TO SSB JOYSTICK CN01 KEY 1 AMBI_SPI_CLK AMBI_SPI_MOSI 100PF 50V +12V_AMBI +12V_AMBI GND_AL AMBI_TEMP +12V_AMBI GND_AL TACT S W 6 P SW01 GND_AL GND_AL Right Center Down GND_AL Left CONN 13P 1.25MM ------ ------ ------...