Related Manuals for Oden Control P50R
Summary of Contents for Oden Control P50R
- Page 1 ® ODEN ELECTRIC ACTUATORS P50R P220R And P500R ´ S GUIDE INSTALLATION AND MAINTENANCE MANUAL Oden P50R Copyright Oden Control AB (publ.) Version GR 2003-10-26...
-
Page 2: Table Of Contents
Content: 1.0 General information ® Oden 1.1 The family 1.2 Operation and safety instructions 2.0 Technical description 2.1 Basic Unit 2.2 Spindle Adapter 2.3 Adapter consoles and screws 2.4.1 Connection board A 2.4.2 Connection board B 2.4.3 Connection board C 2.5 High temperature version—W 3.0 Mechanical installation 3.1 Acceptance control... -
Page 3: General Information
Actuators). Local regulations concerning technical equipment The P50R, P220R and P500R range are must be observed when installing and/or maintaining actuators. but can also be used as multi the actuator. Necessary steps to prevent any accidents turns actuators with a maximum working must be taken. -
Page 4: Basic Unit
® The Oden actuator consists of : No potentiometer or battery are used to 2.1 Basic Unit remember this position value, nor limit switches or other sensitive electro-mecha- nical components. The unit consists of a sealed aluminium housing with a step-motor, a reduction gear- The reduction gearbox is based on the patent box, electronics and terminal blocks. -
Page 5: Connection Board A
C — +90 tools are necessary: is also available. This Basic Unit is called P50W/P220W or P500W. P50R: The internal electronic is protected in a Spanner, 24 mm (cable inlets) separate tight box, which is connected to the Hexagon key, M5 (terminal lid) Basic Unit by a shielded cable. -
Page 6: Installation Of The Actuator
But in spite of that many valve manufacturers still have their own A max A min ® standards, and Oden has designed adapters Oden P50R 52 mm 20 mm to the most common valves on the market. 79 mm 30 mm Oden P220R 3.3.3 Mechanical control... -
Page 7: The Calibration System Pc/Pc
will in any case not damage the actuator. enclosed rubber washer. (Warranty Notice the warning label on the hand-wheel. condition) Careless handling will damage the valve or the actuator. 5. T HE CALIBRATION - PC/PC SYSTEM As an extra protection against overloading the P50 can be delivered with a slipping coupling. -
Page 8: Manual Power Calibration
forces in the valve). The automatic 20-minutes valve normally does not have) or if the valve is calibration will avoid such occurrence. too sensitive for the calibration torque/force (for example the valve will jam at closed position), but yet you require the programmed The electronics will remember the calibration control torque/force, then we recommend position at a power break. -
Page 9: Trouble Shooting
Position Calibration. move. Read the mA-value. Decrease the control signal very slowly until the valve 5.3 Summing up of the spindle starts to move in the other direction. Read the mA-value. The signal difference is a PC / PC – calibration system measure of the system backlash (positioning Using Power Calibration: accuracy). - Page 10 valve can cause problems depending on the making starting attempts continuously during lack of valve lange and spindle standards a long time period, which may cause fatigue damages to the valve or to the Actuator. accepted by the valve manufacturer. ®...
- Page 11 Patent protected in all major countries. US patent 5,913,744 Oden Control AB (publ.) Phone: (+46) 08 767 76 57 Nilstorpsvägen 53 Fax: (+46) 08 767 47 18 181 47 LIDINGÖ E-mail: sales@odencontrol.se Sweden Version GR 2003-10-26...