Table of Contents
Advertisement
Quick Links
20"LCD Color Monitor
Service
Service
Service
Description
Table of Contents......................................................1
Revision List.............................................................2
Important Safety Notice............................................3
1. Monitor Specifications............................................4
2. LCD Monitor Description........................................7
3. Operation Instructions............................................8
3.1General Instructions........................................8
3.2 Control Buttons.............................................8
3.3 OSD Menu......................................................9
4. Input/output Specification...................................10
4.1 Input Signal Connector.....................................10
4.2 Resolution & Preset Modes.................................11
4.3 Pixel Defect Policy.......................................12
4.4 Failure Mode of Panel...................................14
5. Block Diagram...............................................15
5.1 Scaler Board.....................................................15
5.2 Power Board.......................................................16
6. Schematic Diagram.............................................. 18
6.1 Scaler Board..............................................18
6.2 Power Board.......................................................25
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2010 Philips Consumer Lifestyle
201B2CB/00
201BL2CS/00
201B2CB/01
201BL2CB/00
201B2CB/69
201BL2CB/27
201B2CB/75
201BL2CB/93
201B2CS/00
201B2CS/93
Description
Page
6.3 USB Board....................................................31
6.4 Headphone Board..............................................32
6.5 Key Board.................................................33
7. PCB Layout................................................34
7.1 Scaler Board............................................34
7.2 Power Board.............................................36
7.3 USB Board.................................................41
7.4 Headphone Board.......................................41
7.5 Key Board................................................41
8. Wiring Diagram.............................................42
9. Scaler Board Overview..................................44
10. Mechanical Instructions...............................45
11. Repair Flow Chart........................................47
12. ISP Instructions..................................................51
13. DDC Instructions................................................57
14. White Balance, Luminance Adjustment..............72
15. Monitor Exploded View.......................................74
16. Recommended & Spare Parts List...................75
17. Different Parts List......................................78
18. General Product Specification.........................80
SAFETY NOTICE
Subject to modification ○
K
Aug.17, 2010
Chassis: Meridian 2
Page
Advertisement
Table of Contents
Related Manuals for Philips 201B2CB/00
Summary of Contents for Philips 201B2CB/00
-
Page 1: Table Of Contents
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2010 Philips Consumer Lifestyle Subject to modification ○ Aug.17, 2010... -
Page 2: Revision List
Aug.17,2010 Initial release, Draft Version Sep.20,2010 Update BOM for 201B2CS/00 Oct.28,2010 Update BOM for 201B2CB/69 Nov.29,2010 Update BOM for 201B2CB/00 Jan.19,2011 Update BOM for 201B2CB/75 Mar.24,2011 201BL2 initial release Add CTN model 201BL2CB/00 May.11,2011 Add Auto Color SOP into ISP Instruction Add CTN model 201B2CB/01 Aug.04,2011... -
Page 3: Important Safety Notice
Meridian 2 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 4: Monitor Specifications
Meridian 2 1. Monitor Specifications Technical specifications Picture/Display LCD Panel Type TFT-LCD Backlight CCFL (201B2) / LED (201BL2) Panel Size 20″ W ( 50.8 c m) Aspect Ratio 16:9 Pixel Pitch 0.2768 x 0.2768 mm Brightness 250 cd/m² Smart Contrast 500,000:1 (CCFL) / 20M:1 (LED) Contrast Ratio (typical) 1000:1... - Page 5 Meridian 2 Normal Operation (typ.) 19.63 W 19.62 W 19.60 W Sleep 0.1 W 0.1 W 0.1 W 0.1 W 0.1 W 0.1 W AC Input Voltage at AC Input Voltage at AC Input Voltage at Heat Dissipation* 100V AC +/- 5V AC, 115V AC +/- 5V AC, 230V AC +/- 5V AC, 50Hz +/- 3Hz...
- Page 6 Color Black /Silver Finish Texture Note: 1. EPEAT Gold or Silver is valid only where Philips registers the product. Please visit www.epeat.net registration status in your country. 2. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet.
-
Page 7: Lcd Monitor Description
Meridian 2 2. LCD Monitor Description The LCD monitor will contain a scaler board, a power board, an USB board, a headphone board and a key board. The scaler board houses the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC inverter voltage to drive the backlight of panel and the scaler board chips each voltage. -
Page 8: Operation Instructions
Meridian 2 3. Operating Instructions 3.1 General Instructions Connecting to your PC Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor. By changing these setting, the picture can be adjusted to your personal preference. -
Page 9: Osd Menu
3.3 OSD Menu Install base stand Place the monitor face down a smooth surface On-screen Display (OSD) is feature in all Philips LCD taking care to avoid scratching or damaging monitors. It allows an end user to adjust screen the screen. -
Page 10: Input/Output Specification
Meridian 2 Logic GND Sense (GND) Bi-directional data H/H+V sync V-sync Data clock Digital Connectors (Option) Pin No. Signal Name T.M.D.S. data2- T.M.D.S. data2+ T.M.D.S. data2 shield No Connect No Connect DDC clock DDC data No Connect T.M.D.S. data1- T.M.D.S. data1+ T.M.D.S. -
Page 11: Resolution & Preset Modes
Meridian 2 4.2 Resolution & Preset Modes 46.88 800 x 600 75.00 Maximum Resolution 48.36 1024 x 768 60.00 1600 x 900 at 60 Hz (analog input) 60.02 1024 x 768 75.03 1600 x 900 at 60 Hz (digital input) 44.77 1280 x 720 59.86... -
Page 12: Pixel Defect Policy
No manufacturer can guarantee that the monitor displays a dark pattern. There are three panels will be free from pixel defects, but Philips types of bright dot defects: guarantees that any monitor with an unacceptable... - Page 13 In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
-
Page 14: Failure Mode Of Panel
Meridian 2 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. -
Page 15: Block Diagram
Meridian 2 5. Block Diagram 5.1 Scaler Board Keypad Interface Panel Interface (CN404) (CN409) Flash Memory Scaler IC NT68668FG Pm25LD020C-SCE Crystal (Include MCU, ADC, OSD) (U402) 12 MHZ (X401) (U401) EEPROM EEPROM H/Y Sync USB Plug AT24C02BN AT24C02BN (CN801) (U105) (U101) EDID_WP EDID_WP... -
Page 16: Power Board
Meridian 2 5.2 Power Board 201B2 AC input Bridge Rectifier Transformer EMI filter Rectifier Diodes and Filter Feedback Circuit PWM Control TOP266EG Photocoupler (IC901) (IC903) Output MOSFET Transformer Circuit (PT801) AO4614 Lamp Protect Circuit PWM Control ta9687GN ON/OFF (IC801) Feedback Circuit Phone jack Audio Power Amplifier... - Page 17 Meridian 2 201BL2 AC input Bridge Rectifier Rectifier Transformer EMI filter Diodes and Filter Feedback Circuit PWM Control TOP266EG Photocoupler (IC901) (IC903) 1.45V Boost Circuit LED Bar Feedback Circuit LED Driver IC MP3389EF OVP Circuit (U801) ON/OFF Phone jack Audio Power Amplifier APA2071JI-TUG (IC601) Speaker...
-
Page 18: Schematic Diagram
Meridian 2 6. Schematic 6.1 Scaler Board (715G4178M0C000004K) Remark: Parts position can be searched by using FIND function in PDF. 04.SCALER 02.INPUT VCC3.3 VCC3.3 SOG_DET VCC1.8 SOG_DET SOG_DET VCC1.8 05.PANEL INTERFACE EDID_WP AHS0 EDID_WP AHS0 AHS0 AVS0 AVS0 AVS0 PA[0..9] DDCSDA1 DDCSDA1 DDCSDA1... - Page 19 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. D-SUB I/O CN101 DET_VGA R102 100R 1/16W 5% VGA_CABLE_DET VGA_CABLE_DET 5 DB15 VGA_5V DDCSCL1 R101 DDCSCL_A DDCSCL1 100R 1/16W 5% VGA_5V VSIN0 ZD101 BIN0- HSIN0 BIN0 R103 R104 R105...
- Page 20 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. DVI Input R127 DVI_CABLE_DET 5 100R 1/16W 5% DVI5V CN102 D102 3,5,7 VSY NC DET_DVI DVI5V SYNC GND SCL_DVI R128 100R 1/16W 5% DDC SCL SDA_DVI R129 100R 1/16W 5% ESD_DVI...
- Page 21 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. VCC1.8 Scaler FB401 CVDD 300OHM R402 NC/2K2 1/16W 5% CN401 PB[0..9] PB[0..9] LVB3P LVB3M R403 NC/2K2 1/16W 5% C401 C402 C403 LVBCKP VCC3.3 LVBCKM 100NF 25V 100NF 25V 100NF 25V LVB2P...
- Page 22 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. PA[0..9] PB[0..9] PA[0..9] PB[0..9] Panel Interface LVB3P CN408 LVA3P LVB3M NC/CONN LVA3M LVBCKP LVB0M RXO0- LVACKP LVBCKM LVB0P RXO0+ LVACKM LVB2P LVB1M RXO1- LVA2P LVB2M LVB1P RXO1+ LVA2M LVB1P...
- Page 23 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. Power VCC3.3 U701 3,4,5 VCC3.3 5 VIN VOUT VCC3.3 C703 C704 100NF 25V C702 100NF 25V C701 R702 100uF16V 10K 1/16W 5% 100NF 25V +5V 3,4,5 CN701 R703 1K 1/16W...
- Page 24 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. USB Plug CN801 CN802 CONN CONN...
-
Page 25: Power Board
Meridian 2 6.2 Power Board 201B2 715G3974P01000001H Remark: Parts position can be searched by using FIND function in PDF. Power R918 100 OHM 1/4W C912 C910 R919 100 OHM 1/4W BD901 +16V L904 C900 R920 3.5uH D2SB80 3300PF/250V 100 OHM 1/4W 2N2 500V 2N2 500V R947... - Page 26 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. Inverter R817 2R2 +-5% 1/8W +16V Q805 ON/OFF D802 D803 R803 R816 2R2 +-5% 1/8W R804 5K1 +-5% 1/8W 5K1 +-5% 1/8W 1N4148-B4006 PT801 APM4568AKC-TRG 1N4148-B4006 POWER X'FMR C815 100N 50V...
- Page 27 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. Audio +5V1A +5V1A FB601 R602 +5V1A 10K 1/10W 5% +5V1 C602 CN604 BEAD R616 C603 470nF 16V R603 C609 100K 1/10W 5% 470nF 16V R613 470 OHM +-5% 1/6W 10K 1/10W 5% 1U 25V C614...
- Page 28 Meridian 2 201BL2 715G3974P01001001S Remark: Parts position can be searched by using FIND function in PDF. Power R918 100 OHM 1/4W C912 C910 R919 100 OHM 1/4W BD901 +16V L904 C900 R920 3.5uH ZD902 D2SB80 3300PF/250V 100 OHM 1/4W 2N2 500V 2N2 500V R947 R946...
- Page 29 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. +5V1A +5V1A Audio FB601 R602 +5V1A 10K 1/10W 5% +5V1 C602 CN604 BEAD R616 C604 C603 100uF25V 470nF 16V R603 C609 100K 1/10W 5% 470nF 16V R613 470 OHM +-5% 1/6W 10K 1/10W 5%...
- Page 30 Meridian 2 201BL2 715G4013P02002004S Remark: Parts position can be searched by using FIND function in PDF. Converter F801 0R05 4A 1/4W L801 22uH D801 B3100B +14.5V R801 10 OHM 1% 1/4W R805 CN801 300K 1/8W NC/CN804 Q806 NC/Q801 C809 C810 C807 NC/CONN P8008HV...
-
Page 31: Usb Board
Meridian 2 6.3 USB Board (715G4330T0B000004M) Remark: Parts position can be searched by using FIND function in PDF. CN702 CN701 L701 USB CONN 120OHM CONN L702 120OHM C701 1N 50V... -
Page 32: Headphone Board
Meridian 2 6.4 Headphone Board (715G4331T0B000004M) Remark: Parts position can be searched by using FIND function in PDF. CN002 CN001 Headset_R Headset_R Earphone_Det Earphone_Det Headset_L Headset_L PHONEJACK Ear-phone CONN... -
Page 33: Key Board
Meridian 2 6.5 Key Board (715G4196K1A000004S) Remark: Parts position can be searched by using FIND function in PDF. CN001 V3.3 5V_LED SM_CLK R005 100R 1/10W 5% V3.3 SM_DATA R006 100R 1/10W 5% DATA SM_INT# R020 AC_SHIELD U001 R001 R002 R003 D001 CONN RLZ6.8B... -
Page 34: Pcb Layout
Meridian 2 7. PCB Layout 7.1 Scaler Board (715G4178M0C000004K) Remark: Parts position can be searched by using FIND function in PDF. CN409 CN408 R707 CN406 C434 C701 R449 FB409 R448 U703 U704 C705 C711 C433 C713 FB410 U702 U701 C702 C710 FB401 Q704... - Page 35 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF.
-
Page 36: Power Board
Meridian 2 7.2 Power Board 201B2 715G3974P01000001H Remark: Parts position can be searched by using FIND function in PDF. CN903 J902 J901 R947 C915 L801 R946 L903 L904 ZD902 CN902A F903 J806 L905 Q903 C819 CN801 C918 C916 D906 C917 CN902 J807 F902... - Page 37 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. C810 R843 D806 D807 R838 R842 C813 R943 Q802 D805 R813 C808 R808 C809 R815 C805 C910 C912 IC801 C935 C818 C812 C929 R962 C806 R961 R935 C924 Q805...
- Page 38 Meridian 2 201BL2 715G3974P01001001S Remark: Parts position can be searched by using FIND function in PDF. J902 J901 CN903 R947 L903 CN902A C915 R946 F903 L904 L905 ZD902 CN801 C916 C917 C918 Q903 F902 FB901 D906 CN902 D903 D905 D904 FB601 IC904 J914...
- Page 39 Meridian 2 Remark: Parts position can be searched by using FIND function in PDF. R943 C910 C912 C935 C929 R962 R961 R935 C924 R927 R930 R924 R925 R940 R926 R912 R906 C923 R905 C922 R909 R907 Q608 R612 R601 R619 R620 C613 Q607...
- Page 40 Meridian 2 201BL2 715G4013P02002004S Remark: Parts position can be searched by using FIND function in PDF. D801 C807 L801 Q801 Q806 C809 R801 C805 R822 U801 F801 R821 R826 C803 Q802 C804 R820 C811 R805 CN802 C812 R823 C801 R851 R846 R841 R842...
-
Page 41: Usb Board
Meridian 2 7.3 USB Board (715G4330T0B000004M) Remark: Parts position can be searched by using FIND function in PDF. C701 L701 CN701 CN702 L702 7.4 Headphone Board (715G4331T0B000004M) Remark: Parts position can be searched by using FIND function in PDF. CN001 CN002 7.5 Key Board (715G4196K1A000004S) Remark: Parts position can be searched by using FIND function in PDF. -
Page 42: Wiring Diagram
Meridian 1 8. Wiring Diagram 201B2 Panel CN408 CN802 Scaler Board Power Board U401 CN803 CN603 CN802 CN901 USB Board CN601 CN101 CN102 CN002 CN001 SPK R Key Board SPK L CN001 HEA Board... - Page 43 Meridian 1 201BL2 Panel CN801 CN408 Converter Board Scaler Board Power Board CN805 U401 CN802 CN603 CN802 CN901 USB Board CN601 CN101 CN102 CN002 CN001 SPK R Key Board SPK L CN001 HEA Board...
-
Page 44: Scaler Board Overview
Meridian 3 9. Scaler Board Overview FFC Cable DC-DC Scaler Flash ROM DVI EEPROM VGA EEPROM Note: DVI EEPROM is available for selective models. -
Page 45: Mechanical Instructions
Meridian 3 10. Mechanical Instructions Note: Take the 201B2 for example (the way of 201BL2 disassembly is the same as 201B2) direction as the picture to open other latches. Step 3: Remove the mainframe 1. Disconnect the key cable, headphone cable and speaker cable. - Page 46 Meridian 2 3. Disconnect two connectors and four screws 3. Disconnect all the connectors 4. Disconnect the FFC cable. to Speaker to HEA Board to Panel Step 4: Remove the boards to Power Board 1. Remove the four screws that secure the connectors.
-
Page 47: Repair Flow Chart
Meridian 2 11. Repair Flow Chart 1. No Power No power Check power cable is Re-plug the power cable tightened? Check Power “On/Off” Turn on the Power “On/Off” switch is “On”? Check the LED Check the AC power indicator is OK? Replace the power board and check connections Replace main board and check connections Replace key board and check connections... - Page 48 Meridian 2 No Video (Power LED White) No Video (Power LED White) Press the power Replace the main board button is OK? Replace the power The end board and connection Replace the main The end board and connection Check the FFC cable Replace the FFC cable or panel or panel...
- Page 49 Meridian 2 3. DIM DIM (image overlap, focus or flicker) Reset in factory mode The end Set to the optimal The end frequency, select the recommended frequency Readjust the phase and pixel The end clock in the user mode Pull out signal cable and Check the signal cable check “Self Test Feature and the PC...
- Page 50 Meridian 2 4. Color is not optimal Color is not optimal Color shift Miss color Reset the factory mode Replace the signal cable In the user mode, set the “color settings” until customer satisfy The end Pull out the signal cable and check the screen color display is normal? Replace the signal cable or PC...
-
Page 51: Isp Instructions
If the monitor can’t be power on, after programming, switch the source to “Gray” or “black and white” pattern and VGA mode, then do “Auto Color/Level”. Connect to DC 12V Input the PC LPT Connect this port to the Philips model VGA port 12.3 The process of ISP writing as follows:... - Page 52 Meridian 2 1. Double-click to running the program as follows: 2. Judge the monitor whether belong to “data in flash” or not, if belong to it, please click “option” item and select “FE2P Mode Enable”, otherwise, don’t do any actions. Like as below picture:...
- Page 53 Meridian 2 3. Click “option” and select “Setup ISP tool ”, 4. Select the “NVT Type I (default)”, click the icon “Confirm Change”. and then click the “OK”...
- Page 54 Meridian 2 Note: when click the icon “Confirm Change”, if the following picture appears, you must install the “ntport24”. Click icon, choose the correct program, and then click open:...
- Page 55 Meridian 2 6. Click icon. After display “Chip erase OK.”, “Programming Success”, “ISP OFF”, it means F/W updated OK, it will show as the follow picture: 12.4 Check the firmware version: Take the 202E2 for example as below. 1. Press buttons at the same time, power on the monitor, and then press the menu again;...
- Page 56 Meridian 2 4. AC on/off to exit the factory mode. 5. Press “MENU” to enter into user mode to restore the factory setting. Otherwise, monitor will not be able to save setting. If not save the setting, when AC ON/OFF, it will can’t find the boot LOG from the screen. As the below pictures: Note: If DVI no picture or VGA can’t be adjusted to the best resolution, please rewrite EDID.
-
Page 57: Ddc Instructions
13.2 Connect the EDID Board as follow: Note: when update, should make sure the LCD AC on, DC on. Connect this port to the Philips model DVI-D port Connect to the PC LPT Connect this port to the Philips model VGA port... - Page 58 Meridian 2 1. Rename the EDID data to “wa”, “wd”. 2. Put the “wa” and “wd” into a new folder, and then create another new folder named “ddc” (It must be “ddc” instead of other names). Step1: Must put the “ddc” folder and “TPVDDC6.0.exe” into the same folder. Step2: Must copy the folder which contains EDID data and “config”...
- Page 59 Meridian 2 3. Double-click , and choose the “Analog and DVI”, it will show the picture as follow: 4. Click “LoadFile”, it will show the picture as follow:...
- Page 60 Meridian 2 5. Click “OK”, it will show the picture as follow: 6. Key in the same 14 numbers in the Input SN and Verify SN.
- Page 61 Meridian 2 7. Click “Program”, if it shows the below mistake, please try to write again.
- Page 62 Meridian 2 8. If it shows the below picture, it means the write is successful. 9. Click “ReadBoth”, if the DDC Write is OK, it will show the picture as follow: The information must be the same as the data you have loaded.
- Page 63 Meridian 2 10. Click “program”, if the 12V connector is not OK, it will show the picture as follow: 11. Click “program”, if the cable connector is not OK, it will show the picture as follow:...
- Page 64 Meridian 2 201B2 EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 9C 08 D3 86 03 00 10| 0C 14 01 03 6C 2C 19 78 2A B8 15 A6 55 4B 9B 25 20| 13 50 54 BD 4B 00 81 C0 81 00 81 80 A9 C0 01 01 30| 01 01 01 01 01 01 30 2A 40 C8 60 84 64 30 18 50 40| 13 00 BB F9 10 00 00 1E 00 00 00 FF 00 32 33 31...
- Page 65 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1600 x 900 @ 60Hz <-Detailed Timing Descriptions: -> FC (Monitor Name): Philips 201B FD (Monitor Limits): Min. V. rate: 56 Hz Max. V. rate: 76 Hz Min. H. rate: 30 KHz Max.
- Page 66 Meridian 2 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 9C 08 D3 86 03 00 10| 0C 14 01 03 80 2C 19 78 2A B8 15 A6 55 4B 9B 25 20| 13 50 54 BD 4B 00 81 C0 81 00 81 80 A9 C0 01 01 30| 01 01 01 01 01 01 30 2A 40 C8 60 84 64 30 18 50 40| 13 00 BB F9 10 00 00 1E 00 00 00 FF 00 32 33 31...
- Page 67 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1600 x 900 @ 60Hz <-Detailed Timing Descriptions: -> FC (Monitor Name): Philips 201B FD (Monitor Limits): Min. V. rate: 56 Hz Max. V. rate: 76 Hz Min. H. rate: 30 KHz Max.
- Page 68 Meridian 2 201BL2 EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 97 08 D3 86 03 00 10| 02 15 01 03 6E 2C 19 78 2A EC 85 A2 54 4D A1 27 20| 12 50 54 BD 4A 00 A9 C0 01 01 01 01 01 01 01 01 30| 01 01 01 01 01 01 30 2A 40 C8 60 84 64 30 18 50 40| 13 00 BB F9 10 00 00 1E 00 00 00 FF 00 32 33 31...
- Page 69 1024 x 768 @ 75Hz VESA Established Timings 3:00 <-Standard Timing Identification: -> 1600 x 900 @ 60Hz <-Detailed Timing Descriptions: -> FC (Monitor Name): Philips 201BL FD (Monitor Limits): Min. V. rate: 56 Hz Max. V. rate: 76 Hz Min. H. rate: 30 KHz Max.
- Page 70 Meridian 2 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 97 08 D3 86 03 00 10| 02 15 01 03 80 2C 19 78 2A EC 85 A2 54 4D A1 27 20| 12 50 54 BD 4A 00 A9 C0 01 01 01 01 01 01 01 01 30| 01 01 01 01 01 01 30 2A 40 C8 60 84 64 30 18 50 40| 13 00 BB F9 10 00 00 1E 00 00 00 FF 00 32 33 31...
- Page 71 1024 x 768 @ 75Hz VESA Established Timings 3:00 <-Standard Timing Identification: -> 1600 x 900 @ 60Hz <-Detailed Timing Descriptions: -> FC (Monitor Name): Philips 201BL FD (Monitor Limits): Min. V. rate: 56 Hz Max. V. rate: 76 Hz Min. H. rate: 30 KHz Max.
-
Page 72: White Balance, Luminance Adjustment
Meridian 2 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 201B2.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing b. - Page 73 Meridian 2 5. Color Temp confirmation Connect the signal to the monitor, the monitor displays white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC. 6.
-
Page 74: Monitor Exploded View
Meridian 2 15. Monitor Exploded View 201B2 & 201BL2... -
Page 75: Recommended & Spare Parts List
Meridian 2 16. Recommended & Spare Parts List Recommended Parts List for 201B2CS/00 Item Location PCM Codes Description Remark FQ106 A34G2228BDYA1S0130 BEZEL L20WA-TPH2B-S1 FQ401 078G015A 3 V SPK 4 OHM 1.5 W 200/200mm 26.9X13.9mm FQ004 KEPCAQB2 KEY BOARD ASSY FQ014 HJPFAQB2 HEADPHONE BOARD FQ006... - Page 76 Meridian 2 F901 084G 56 4 B FUSE 4A 250V F903 084G 56 4 B FUSE 4A 250V U001 056G 669 15 TOUCH KEY IT7230BFN/BX-0001(R) QFN24 Recommended Parts List for 201BL2CS/00 Item Location PCM Codes Description Remark FQ106 A34G2228BDYB2S0130 BEZEL L20WA-TPH2B-S1 FQ401 078G015A 3 V SPEAKER 4 OHM 2W 26.8X13.8 210/70...
- Page 77 Meridian 2 T901 080GL19P 11 S XFMR 650UH 10% 15UH BCK-EFD30-29009 IC904 056G 563354 Shunt. Reg. TL431-A-TA TO-92 F903 084G 56 4 B FUSE 4A 250V F901 084G 56 4 B FUSE 4A 250V IC901 056G 379181 AC/DC CONVERTER TOP266EG eSIP-7C U801 056G 700 5 IC LED driver MP3389EF TSSOP28...
-
Page 78: Different Parts List
Meridian 2 17. Different Parts List Diversity of 201B2CS/93 compared with 201B2CS/00 201B2CS/93 201B2CS/00 Location PCM Codes Description Location PCM Codes Description Diversity of 201B2CB/00 compared with 201B2CS/00 201B2CB/00 201B2CS/00 Location PCM Codes Description Location PCM Codes Description FQ106 A34G2228 KSA1S0130... - Page 79 Meridian 2 Diversity of 201B2CB/75 compared with 201B2CS/00 201B2CB/75 201B2CS/00 Location PCM Codes Description Location PCM Codes Description FQ301 089G412A18NIS3 AC POWER CORD 1800mm E08901 089G404A18N CX POWER CORD FQ106 A34G2228 KSA1S0130 BEZEL L20WA-TPH2B-S1 FQ106 A34G2228BDYA1S0130 BEZEL L20WA-TPH2B-S1 FQ109 A34G1983ADT 2S0100 BASE FQ109 A34G1983BDY 1S0100...
-
Page 80: General Product Specification
WINDOWS 7/VISTA PREMIUM LOGO CERTIFICATION HDCP SUPPORT SMART CONTROL PREMIUM REQUIREMENT SMART CONTRAST 500K:1 (Typical) Waiting for supplier input SMART Image PREFECTTUNE II (formerly FGA, FACTORY GAMMA Alignment) PHILIPS LOGO DISPLAYED WHILE POWER ON WEEE REQUIREMENT RoHS REQUIREMENT TCO5.0 REQUIREMENT... - Page 81 4.5 Check Cross Talk(s) 4.6 Color Temperature Adjustment 5. Mechanical Characteristics 5.1 Cosmetic 5.2 Mechanical Data Files 5.3 Location of Philips Logo 5.4 Gap between Panel and Front Bezel 5.5 Location Control Icons 5.6 Color for Resin/Paint 5.7 Fire Enclosure Request 5.8 Resins...
- Page 82 Meridian 2 5.13 Tilt and Swivel Base 5.14 Kensington Lock 5.15 Label 5.16 Product Dimension / Weight (refer to Philips approved SHT191 /SHT560) 5.17 Transportation 5.18 Pallet / Container Loading (refer to Philips approved SHT560) 6. Environmental Characteristics 6.1 Susceptibility of Display to External Environment 6.2 Transportation Tests...
-
Page 83: Foreword
All optical characteristics are determined according to panel specification after warming up approximate 30 minutes. 2. Product Profile This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated tilt base. 2.1 EDID Header Data for EDID &... - Page 84 Meridian 2 Contrast ratio : >=1000:1 (typ.) White luminance : 250 (center, typ.) Color gamut : >=72% Gate IC : SEC Source IC : SEC Response time : 5 ms (typ.) LGD (2nd source) Type NR. : LGD LM200WD1-TLD1/TLD3 Resolution : 1600 x 900 @60Hz Outside dimensions : 462.8 (H) x 272.075 (V) x 14.5 (D) (typical)
-
Page 85: Scanning Frequencies
Scaler should be capable of below items. 1) Scaler must support color engine for Image enhancement feature (SmartImage) 2) Scaler must have enough memory to support PerfecTune feature and Philips OSD 3) Scaler must support Dynamic Contrast Ratio (DCR), 500K: 1 DCR preferred 3.1 Interface signals... -
Page 86: Interface
Meridian 2 3.2 Interface 3.2.1 D-Sub Cable Length : 1.8 M +/- 50 mm Fix with monitor when packing, with transplant pin protective cover. Connector type : D-Sub male with DDC2B pin assignments. Blue connector thumb-operated jack screws Pin assignments: Signal Assignment Signal Assignment DDC +3.3V or +5V... -
Page 87: Timing Requirement
OSD LANGUAGES 9 LANGUAGES H9 new item WOW_ feature translation _ 200 translation _ 200 OSD TREE 201B2 OSD TREE.xls Power On Logo: Power On Show up Philips logo 3 seconds POWER ON LOGO Change to input signal. -
Page 88: Horizontal Scanning
Meridian 2 This picture is reference only. The official drawing will send out by PM. Stand-alone – On: Isolate video and audio control input Stand-alone – Off: Audio Selection Integrate video and audio control input Mute – On: Turn off audio Mute –... -
Page 89: Ddc /Ci Support And Smart Manage /Control
Meridian 2 3.11 DDC /CI Support and Smart Manage /Control In accordance with VESA DDC/CI and MCCS ver.2.0, the monitor should be workable with, Philips SmartManage, SmartControl V6.1, and Portrait Display Tune at least 3.12 Hot-key definition D:\ENG\monitor projects\spec\H8\hot k 3.13 Smart contrast... - Page 90 Meridian 2 For example, SmartImage is on with “Game” profile at VGA input, when switch to DVI input, the Smart Image will revert to previous profile of DVI. In the input switching process the “SmartImage” OSD will also show up to present which profile is selected if “Smart Image”...
- Page 91 Meridian 2 SmartContrast enhancement by histogram analysis should be implemented. 2. Sharpness enhanced 90%. 3. Color enhancement set as the same with Video. 4. Color temperature set to 7500° (Based on final PQ settings) (if higher) 5. Brightness level sets to maximum. 6.
-
Page 92: Perfect Tune
Meridian 2 There is OSD showing “SmartImage Lite & SmartResponse Demonstration” in left frame and “Original Image” in right frame. iii. The OSD word color is white with transparent background. The demo profile will be “Video Playback” profile with “High” ODC setting. The current SmartContrast value also is shown on the bottom of the screen. -
Page 93: Color Temperature Adjustment
Meridian 2 ABS (YA - YB) ⎯⎯⎯⎯⎯⎯⎯⎯⎯ X 100% < 1.5 % 4.6 Color Temperature Adjustment There are three factory preset white color 9300K, 6500K, sRGB. Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x, y) coordinate for the screen center should be: Product Specification CIE coordinates... -
Page 94: Mechanical Characteristics
All major plastic parts (bezel, back cover) need to be molded from same resin. Plastic resin type selection should be referred to “TY R83-2-9002-1”. 5.12 Texture/Glossing of housing The texture area and texture no should follow Philips make-up sheet. The exterior surfaces shall have a uniform texture. - Page 95 5.15 Label Regulatory label / Carton label should follow Philips requirement. China RoHS label Detail document refer to Philips Engineering Reference Book 5.16 Product dimension / Weight (Refer to Philips approved SHT191 / SHT560) Unit dimension: Packed unit dimension: Net weight: Gross weight: 5.17 Transportation...
- Page 96 Meridian 2 • Un-package test 1. Half sine shock test (non operation) B. Transportation test specification for China/India • Package test 1. Random Vibration test 2. Drop test 3. Cold Drop test (for design reference) • Un-package test 1. Sine vibration (operating) 2.
-
Page 97: Bright Dot Defects
According to MIL-STD-1916D Control II level AQL: NA (Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 1 lit sub-pixel... -
Page 98: Total Dot Defects
Meridian 2 Black dot defects within 20 mm circle* Total black dot defects of all type TOTAL DOT DEFECTS ACCEPTABLE LEVEL Total bright or black dot defects of all type * 1 or 2 adjacent sub-pixel defects = 1 dot defect Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 127 (255 Gray level) - Page 99 10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 10.3 RoHS Restriction on the use of certain hazardous substances.
- Page 100 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.