Advertisement
Available languages
Available languages
Built-In Electric Oven
Installation
Instructions
IMPORTANT – Save for local
electrical inspector's use!
The rating plate is located on the internal side of the oven left hand side trim, it is visible when door is open.
!
CAUTION – To avoid the risk of electrical shock, turn
off power to oven branch circuit.
1. Check your local electric code or National Electric
Code through your power company or secure the
services of a qualified electrician.
CAUTION – TO AVOID THE RISK OF FIRE:
!
If your household branch-circuit wiring is alumi-
num, you must use special connectors designed for
this purpose and listed by Underwriters Laborato-
ries. Be certain to follow the connector manufac-
turer's instructions carefully.
FIGURE 1
1 1/2" min.
28 1/8" min.
29 5/8" max.
24 1/4"
26 7/8"
1 3/4" min.
29 1/8"
1 3/4"
4 MOUNTING
SCREWS
NOTE: Allow at least 26 1/4" clearance for door depth
when it is open.
Maintain a minimum distance of 3" to a wall
located on the door hinge side of the wall oven.
2. Measure cabinet carefully to ensure adequate clear-
ance and proper fit. Do not install wall oven under
the counter top.
This oven requires a wall or cabinet opening of
28 1/8" high by 24 7/8" wide and 23 1/2" deep mini-
mum.
Install the oven at least 10" above the floor (refer to
figure 1).
27" min.
HOLE
FOR
CABLE
23 1/2" min. (depth)
24 7/8" min. (large)
25 5/32" max.
GROUNDED
ELECTRICAL
JUNCTION BOX
10" min.
72"
CABLE
READ THESE INSTRUCTIONS
BEFORE INSTALLING THE OVEN.
3. Cut out cabinet to size specified on this sheet.
Construct support-floor or 2 x 4 rails, covered with
plywood or similar material. Check and level front
to rear and side to side on support floor or rails.
Make sure this support is rigidly mounted, as it sup-
ports the total weight of the unit (110 lbs). MAKE
SURE THAT JUNCTION BOX IS PROPERLY LOCATED
AS SHOWN IN DIAGRAM.
Leave the bottom of the cabinet partially opened to
permit free air circulation, otherwise water conden-
sation may appear inside the control panel when
operating the oven.
4. Remove all shipping and packing materials from
unit and the lower grill assembly packed with the
oven.
5. There is 1 1/2" height adjustment on these models.
(See Figure 2) With this adjustment and a 1/2" top
trim overhand, a unit can be installed in existing
opening 28 1/8" to 29 5/8" high.
3" max.
FIGURE 2
1
DOOR
OPENING
OVEN
BOTTOM
MAX.
EXTENSION
1 1/2"
318128601 (9806) Rev. D
EXTENSION
PANEL
MOUNTING
SCREWS
SIDE
OF OVEN
Printed in Canada
Advertisement
Table of Contents
Related Manuals for Frigidaire FEB702CESG
Summary of Contents for Frigidaire FEB702CESG
- Page 1 IMPORTANT – Save for local electrical inspector’s use! The rating plate is located on the internal side of the oven left hand side trim, it is visible when door is open. CAUTION – To avoid the risk of electrical shock, turn off power to oven branch circuit.
-
Page 2: Electrical Shock Hazard
8. Using the holes in the oven front frame as tem- plate, drill 1/8” diameter holes in the cabinet. 9. Fasten the top of the oven to the cabinet by means of 2 of the screws supplied in the miscellaneous parts bag. -
Page 3: Grounding Instructions
E. Connect the bare copper grounding wire to the grounding wire in the junction box. Check Oven Operation 1. Check the oven in Bake. Turn the Oven Selector Knob to “Bake” and set the Oven Temperature Knob to 350°F. The Lower Oven Element should become red and the “Bake”... -
Page 4: Door Reversing
FIGURE 6 HANDLE This wall oven can easily be modified to a left or a right hand door opening. It is preferable to reverse door opening prior to the installation of the wall oven into the cabinet cavity. If wall oven is already installed, remove the 4 lateral screws securing it against the cabinet, then pull wall oven outward by approx. - Page 5 Horno eléctrico empotrado Instrucciones para la instalación IMPORTANTE - Guarde estas instrucciones para uso del inspector eléctrico local! La placa de potencia indicada está ubicada en la parte interior del contramarco izquierdo del horno. Está visible cuando la puerta está abierta. AVISO - Para evitar el riesgo de choque eléctrico, cierre la energía eléctrica al circuito derivado del horno.
- Page 6 Para ajustar la altura del horno: A. Ponga el horno apoyado en la parte trasera. (Vea la Figura 2). B. Quite los 6 tornillos que sujetan el panel de extensión lateral a los lados inferiores del horno. C. Mueva cada panel hacia abajo, hasta la posición que aumenta la altura del horno para que se adapte a la apertura que usted tiene.
- Page 7 FIGURA 4 Cable de suministro de energía Alambres rojos Alambres blancos Alambre pelado o verde Cable del horno TOMA A TIERRA AL NEUTRO Instrucciones de conexión a tierra Este electrodomestico se ha fabricado con un cable para el suministro de energía que tiene un alambre neutro (blanco) y un alambre verde de toma a tierra conectado al gabinete.
-
Page 8: Inversión De La Puerta
FIGURA 6 TIRADOR Este horno de pared puede modificarse facilmente para abrirse al lado izquierdo o al lado derecho. Es preferible de invertir la abertura de la puerta antes de realizar la instalación del horno en la cavidad del gabinete. Si el horno de pared ha sido ya instalado, remueva los 4 tornillos laterales que aseguran el horno al gabinete, luego saque el horno hacia fuera aproximadamente...