EN 2 3139 785 32070 Technical Specifications and Connection Facilities LOCATION OF PC BOARDS HTS3325 VERSION VARIA TIONS: HTS3325 Type /Versions: Features & Progressive Scan Line-Out TV-In Aux-In Y/Pb/Pr (YUV) Component Video Output CVBS SCART...
Page 3
3139 785 32070 EN 3 Technical Specifications and Connection Facilities 1. Specifications General: AMPLIFIER: Mains voltage : 230V Output power Mains frequency : 50Hz Front : 100W RMS / channel Power consumption : 150W Rear : 75W RMS / channel <...
EN 4 3139 785 32070 Measurements Setup, Service Aid & Lead Free Requirements 2. Measurements Setup, Service Aid & Lead Free Requirements MEASUREMENT SETUP Tuner FM Bandpass LF Voltmeter 250Hz-15kHz e.g. PM2534 e.g. 7122 707 48001 RF Generator e.g. PM5326 S/N and distortion meter e.g.
Page 5
3139 785 32070 EN 5 Measurements Setup, Service Aid & Lead Free Requirements SERVICE AIDS Service Tools: Universal Torx driver holder ........4822 395 91019 Torx bit T10 150mm ..........4822 395 50456 Torx driver set T6 - T20 ......... 4822 395 50145 Torx driver T10 extended ........
Page 6
EN 6 3139 785 32070 Measurements Setup, Service Aid & Lead Free Requirements WAARSCHUWING WARNING Alle IC’s en vele andere halfgeleiders zijn All ICs and many other semi-conductors are gevoelig voor electrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan Careless handling during repair can reduce life de levensduur drastisch doen verminderen.
Page 7
Due to lead-free technology some rules have to be respected by the workshop during a repair: • Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment.
EN 8 3139 785 32070 Measurements Setup, Service Aid & Lead Free Requirements 2.2 Service Hints CAUTION CHARGED CAPACITORS ON THE SERVO BOARD MAY DAMAGE THE DRIVE ELECTRONICS WHEN CONNECTING A NEW DRIVE.THAT’S WHY, BESIDES THE SAFETY MEASURES LIKE • SWITCH OFF POWER SUPPLY •...
3. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: www.p4c.philips.com...
Page 10
EN 10 3139 785 32070 Directions for Use...
3139 785 32070 EN 11 Dismantling Instructions & Service Positions Dismantling Instructions Dismantling of the DVD Loader Tray Cover Dismantling of the Front Board, PSU Module & DVD Loader. 1) Insert a minus screwdriver and push the lever in the direction as shown in Figure 4-1 to unlock the tray before 1) Release 4 snap hooks to remove the Front Board.
Page 12
EN 12 3139 785 32070 Dismantling Instructions & Service Positions Dismantling of the Tuner Module & Mono Board. 1) Loosen 1 screw to remove the Tuner Module. 2) Loosen 2 screws D to remove the Mono Board. Figure 4-5 (AP) Figure 4-6...
Page 13
3139 785 32070 EN 13 Dismantling Instructions & Service Positions Service Positions Service Position - Front Board Service Position - Mono Board Insulation Sheet Service Position -Amp-Board...
EN 14 3139 785 32070 Service Test Program Service Test Program To start service test program refers to Service Mode open the tray with remote control refers to Version or front panel key, while plugging xx refers to Software version number of BEA in the mains cord press 2, 5 8 on (counting up from 01 to 99) remote control, the tray will close...
Page 15
3139 785 32070 EN 15 Service Test Program 5.1.1 Reprogramming of DVD version Matrix 5.1.5 Procedure to check the firmware version to confirm upgrading After repair, the customer setting and region code may be lost. Reprogramming will put the set back in the state in which it has left 1.
Page 16
EN 16 3139 785 32070 Service Test Program Notes:...