Page 2
EN 2 3139 785 31590 Technical Specifi cations and Connection Facilities LOCATION OF PC BOARDS AV Board PCBAS 9.1 AV Interface Board Tuner Loader HTS3455 PCBAS Front Panel VERSION VARIATIONS: HTS3445 Type /Versions: Features & Progressive Scan Digital-In (Coax) TV-In Aux-In Y/Pb/Pr (YUV) Component Video Output CVBS...
Page 3
Technical Specifi cations and Connection Facilities 3139 785 31590 EN 3 1. Specifi cations General: AMPLIFIER: Mains voltage : 120V/230V Output power Mains frequency : 50/60Hz Front : 125W RMS / channel Power consumption : 12W Rear : 125W RMS / channel <...
EN 4 3139 785 31590 Measurements Setup, Service Aid & Lead Free Requirements 2. Measurements Setup, Service Aid & Lead Free Requirements MEASUREMENT SETUP Tuner FM Bandpass LF Voltmeter 250Hz-15kHz e.g. PM2534 e.g. 7122 707 48001 RF Generator e.g. PM5326 S/N and distortion meter e.g.
Page 5
Measurements Setup, Service Aid & Lead Free Requirements 3139 785 31590 EN 5 SERVICE AIDS Service Tools: Universal Torx driver holder ........4822 395 91019 Torx bit T10 150mm ..........4822 395 50456 Torx driver set T6 - T20 ......... 4822 395 50145 Torx driver T10 extended ........
EN 6 3139 785 31590 Measurements Setup, Service Aid & Lead Free Requirements WAARSCHUWING WARNING Alle IC’s en vele andere halfgeleiders zijn All ICs and many other semi-conductors are gevoelig voor electrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan Careless handling during repair can reduce life de levensduur drastisch doen verminderen.
Page 7
Due to lead-free technology some rules have to be respected by the workshop during a repair: • Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment.
Page 8
EN 8 3139 785 31590 Measurements Setup, Service Aid & Lead Free Requirements 2.2 Service Hints CAUTION CHARGED CAPACITORS ON THE SERVO BOARD MAY DAMAGE THE DRIVE ELECTRONICS WHEN CONNECTING A NEW DRIVE.THAT’S WHY, BESIDES THE SAFETY MEASURES LIKE • SWITCH OFF POWER SUPPLY •...
3. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: www.p4c.philips.com...
Page 10
EN 10 3139 785 31590 Directions for Use...
Dismantling Instructions & Service Positions 3139 785 31590 EN 11 Dismantling Instructions Dismantling of the DVD Loader Tray Cover Dismantling of the Front Board, PSU Module & DVD Loader. 1) Insert a minus screwdriver and push the lever in the direction as shown in Figure 4-1 to unlock the tray before 1) Release 4 snap hooks to remove the Front Board.
Page 12
EN 12 3139 785 31590 Dismantling Instructions & Service Positions Dismantling of the Tuner Module & AV Board. Dismantling of the AV Interface Board & PCBAS 9.1 Board 1) Loosen 1 screw (See Figure 4-5) to remove the Tuner Module. 1) Loosen 2 screws (See Figure 4-8) &...
Page 13
Dismantling Instructions & Service Positions 3139 785 31590 EN 13 Service Positions Insulation Sheet PCBA 9.1 AV Board Insulation Sheet Insulation Sheet Service Position - PCBAS 9.1 Service Position - AV Board Front Board Service Position - Front Board...
EN 14 3139 785 31590 Service Test Program Service Test Program To start service test program refers to Service Mode open the tray with remote control refers to Version or front panel key, while plugging xx refers to Software version number of BEA in the mains cord press 2, 5 8 on (counting up from 01 to 99) remote control, the tray will close...
Page 15
3139 785 31590 EN 15 Service Test Program 5.1.1 Reprogramming of DVD version Matrix 5.1.4 Procedure to upgrade the firmware 1. Power up the set and open tray. After repair, the customer setting and region code may be lost. 2. Insert the prepared Upgrade CDROM and close the tray. Reprogramming will put the set back in the state in which it has left 3.
Page 16
EN 16 3139 785 31590 Service Test Program Notes:...
SW3455 Active Subwoofer LOCATION OF PC BOARDS Amplifier PCB Power supply PCB LED PCB SPECIFICATIONS SUBWOOFER Subwoofer (not magnetically shielded design).....................8" Output Power...........................250W (dual 4 ohm) THD (Total Harmonic Distortion) ....................10% at 55 Hz Reproduction Frequency Response....................37Hz-145 Hz Input Sensitivity (Subwoofer In).......................2.6 Vrms AC Power ........................127V / 240V, 50Hz / 60 Hz Power Consumption....................125W (at 1/8 Rated Power) Dimensions (w x h x d)....................240mm x 367mm x 427mm...
Page 38
DISASSEMBLY INSTRUCTIONS Dismantling the Front panel & Speaker Driver 1. Place the Subwoofer Box up side down as shown in the 2. Place the Subwoofer Box as shown in the Picture 2 Picture 1 and use a flat-head screwdriver to gently force and loosen 4 screws to remove the Speaker Driver.