Toro TXL 2000 Operator's Manual
Power rake tool carrier
Hide thumbs
Also See for TXL 2000:
- Operator's manual (60 pages) ,
- Installation instructions (4 pages) ,
- Operator's manual (12 pages)
Related Manuals for Toro TXL 2000
Summary of Contents for Toro TXL 2000
- Page 1 Form No. 3429-955 Rev B Power Rake TXL 2000 Tool Carrier Model No. 22536—Serial No. 318000001 and Up *3429-955* B Register at www.Toro.com. Original Instructions (EN)
- Page 2 1. Model and serial number location The power rake attachment is intended to be used Model No. on a Toro tool carrier. It is designed primarily to prepare seed and sod beds by pulverizing rough soil, dethatching, and removing rocks and debris. Using Serial No.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 General Safety General Safety ........... 3 Slope Safety ............3 Always follow all safety instructions to avoid serious Power Rake Safety ..........4 injury or death. Maintenance and Storage Safety......4 • Do not transport an attachment with the Safety and Instructional Decals ...... -
Page 4: Power Rake Safety
Maintenance and Storage • Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe Safety injury or death. Operating the machine on any slope or uneven terrain requires extra caution. • Check fasteners at frequent intervals for proper •... -
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8061 133-8061 decal125-6128 125-6128 1. High pressure fluid hazard, injection into the body—read the Operator’s Manual before performing maintenance. -
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Move the caster wheels to the operating – No parts required position. Moving the Caster Wheels to the Operating Position No Parts Required Procedure Note: The casters are heavy. -
Page 7: Product Overview
To ensure optimum performance and continued safety • Ensure that all hydraulic-fluid hoses certification of the machine, use only genuine Toro and lines are in good condition and all replacement parts and accessories. Replacement hydraulic connections and fittings are tight... -
Page 8: Starting The Power Rake
CAUTION Hydraulic couplers, hydraulic lines/valves, and hydraulic fluid may be hot. If you contact hot components, you may be burned. • Wear gloves when disconnecting the hydraulic couplers. • Allow the machine to cool before touching hydraulic components. • Do not touch hydraulic fluid spills. g271286 Starting the Power Rake Figure 5... -
Page 9: Adjusting The Angle
To raise the roller, install spacers to the caster Rotate the power rake to the right, left, or straight wheel. To lower the roller, remove spacers from ahead depending on the desired discharge the caster wheel (Figure direction (Figure Install the caster wheel to the caster arm, then Secure the rake by installing the angle pin in the install the remaining spacers on top (Figure... -
Page 10: Operating Tips
Operating Tips • Always begin power raking at the slowest ground speed possible. Increase the ground speed if conditions permit. • Always use the maximum engine speed. • If the roller stalls, slow down the travel speed or decrease the roller depth by raising the roller •... -
Page 11: Maintenance
Maintenance Checking the Hydraulic Lines Determine the left and right sides of the machine from the normal operating position. Service Interval: Before each use or daily WARNING Greasing the Power Rake Hydraulic fluid escaping under pressure can Service Interval: Before each use or daily penetrate skin and cause injury. -
Page 12: Storage
Storage Before long-term storage, wash the attachment with mild detergent and water to remove dirt and grime. Paint all scratched or bare metal surfaces. Note: Paint is available from your Authorized Service Dealer. Store the attachment in a clean, dry garage or storage area. -
Page 13: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The roller does not turn. 1. The hydraulic valve on the traction unit 1. Refer to the traction unit Operator’s is not engaged. Manual. 2. The relief-valve setting on the traction 2. Contact your Authorized Service unit is not properly adjusted. - Page 14 Notes:...
- Page 15 Notes:...
- Page 16 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.