hit counter code
Toro 03227 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 03227
  6. Installation instructions manual
Toro 03227 Installation Instructions Manual

Toro 03227 Installation Instructions Manual

Grass collection system reelmaster 2300/3100-d
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Grass Collection System
Reelmaster
Model No. 03227
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
1
2
3
4
5
6
7
8
© 2014-The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
2300/3100-D
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
No parts required
Front basket bracket-L.H.
Front basket bracket-R.H.
Capscrew-5/16 x 1 inch.
Locknut
Front grass basket assemblies
No parts required
45 degree Fitting w/O-rings
No parts required
Register at www.Toro.com.
WARNING
CALIFORNIA
1
2
-
-
2
2
8
8
2
2
2
4
4
2
-
1
-
Form No. 3380-654 Rev A
Installation Instructions
Use
Mount the roller bumper (Reelmaster
3100D only)
Tension the counterbalance springs
Adjust the front cutting unit shields
Mount the front grass baskets
(Reelmaster 3100D only)
Mount the front grass baskets
(Reelmaster 2000D series only)
Optional basket wheel
Change the hydraulic fitting (Reelmaster
3100D only)
Adjust rear grass shield
Original Instructions (EN)
All Rights Reserved *3380-654* A
Printed in the USA.

Advertisement

Table of Contents
loading

Related Manuals for Toro 03227

Summary of Contents for Toro 03227

  • Page 1: Table Of Contents

    Form No. 3380-654 Rev A Grass Collection System Reelmaster ® 2300/3100-D Model No. 03227 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.

  • Page 2: Procedure

    Procedure Description Qty. Rear basket bracket assembly–L.H. Rear basket bracket assembly–R.H. Capscrew–5/16 x 2–1/4 inches Mount the rear grass basket Locknuts Rear grass basket assembly Adjust the roller bumper(Reelmaster – No parts required 3100D only) Adjusting the rear basket – No parts required position(Reelmaster 3100D only) –...

  • Page 3: No Parts Required

    Tensioning the Adjusting the Front Cutting Counterbalance Springs Unit Shields (Reelmaster 2000D series only) No Parts Required No Parts Required Procedure Procedure 1. Remove the mounting screws securing the front of each front cutting unit shield to the frame (Figure 3). Important: The additional weight of the baskets when 2.

  • Page 4: Front Basket Bracket-L

    3. Latch each hanger bracket over notch on carrier frame (Figure 4). Note: Adjust the sliding hanger brackets so the bottoms of the front baskets are parallel or slightly Mounting the Front elevated with the ground. Grass Baskets (Reelmaster 3100D only) Parts needed for this procedure: Mounting the Front Front basket bracket–L.H.
  • Page 5 Procedure An optional Basket Wheel Kit, Part Number 5–2893 (Figure 7) is available from your local Toro Distributor. Each basket wheel is mounted to the basket bracket with (2) capscrews, flat washers and locknuts. Two rollers are required per basket.
  • Page 6 4. Connect the hydraulic hose to the fitting (Figure 9). Important: On the Reelmaster 2300D only, if the rear basket bracket contacts the reel motor hydraulic hose, replace with Hose Assembly, Toro Part No. 94-5129. Order the Hose Assembly from your Authorized Toro Distributor.
  • Page 7 g025827 Figure 12 3. Rear sliding hanger 1. Rear carrier frame bracket (2) g025825 Figure 10 2. Basket bracket assembly 4. Basket pins 1. Strap 3. Cable tie 2. Strap bolt 4. Wood block 4. Adjust the basket brackets so the bottom of the lower basket flap contacts the top of the roller.
  • Page 8 Figure 14 1. Roller bumper 3. Sliding hanger bracket carriage bolt nuts 2. Wear strip Figure 13 2. Rotate the basket until the roller contacts the middle of 1. Roller bumper the wear strip (Figure 14). 3. Tighten the carriage bolt nuts to secure the basket position.
  • Page 9 2. Rock the basket backward to lift the basket pins out of ballast. Use the following chart to determine the weight or the basket brackets (Figure 16). combinations of weights needed. Cutting Unit Configuration Weight Kits Required Standard machine with 27 inch (1) 83-9370 cutting units &...
  • Page 10 Notes:...
  • Page 11 Notes:...

Table of Contents