Related Manuals for Okayo CAM-9T
Summary of Contents for Okayo CAM-9T
- Page 1 Wireless ENG / EFP System Dual-Antenna Receiver Bodypack Transmitter Handheld Microphone ...
- Page 2 Manufacturer’s Declaration This product meets the following standards: Federal Communications Commission Interference Statement 1. This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body ...
- Page 3 WEEE Statement Electrical and electronic equipment must be disposed of at the end of their lifespan separately from household waste. Please dispose of this equipment at your local waste collection or recycling center. Please help to protect our environment. ...
-
Page 4: Table Of Contents
Table of contents p. 1 ~ p. 4 Quick start Package p. 5 p. 6 ~ p. 8 Illustration Dual-Antenna Receiver Bodypack Transmitter Handheld Microphone p. 9 ~ p. 11 Operation Inserting batteries Powering on Adjusting channels manually ... -
Page 5: Quick Start
WIRELESS ENG / EFP SYSTEM Quick start Step. 1 Insert 2 supplied AA batteries into receiver, transmitter and microphone. Step. 2 Press and hold the power button for 1 second to turn receiver, transmitter or microphone on. Receiver: Step. 3 1. - Page 6 WIRELESS ENG / EFP SYSTEM Bodypack Transmitter: Press and hold the set button for 1 second until backlit screen turns to white and channel number flashes. Press or button to select preferred channel on receiver and transmitter. Press the set button again to confirm newly selected channel.
- Page 7 WIRELESS ENG / EFP SYSTEM Step. 4 Connect one of supplied cable from LINE OUT jack on receiver to camera or recording device. Receiver with 1/8” / XLR cable Receiver with 1/8” / 1/8” cable Antennas of Receiver are recommended to be sloped at a 45- degree angle as shown below to make sure best operation range.
- Page 8 WIRELESS ENG / EFP SYSTEM Step. 6 Tune the headphone and microphone volume to desired level for most appropriate operation. Warning! Kindly note listening at high volume for long periods may damage your hearing.
-
Page 9: Package
WIRELESS ENG / EFP SYSTEM Package Standard 1 dual-antenna receiver 2 bodypack transmitter 2 lapel microphone LM-95C 1 shoe adapter SM-9 1 1/8” to XLR connecting cable 1 1/8” to 1/8” connecting cable 6 AA alkaline batteries ... - Page 10 WIRELESS ENG / EFP SYSTEM Illustration Dual-Antenna Receiver Dual bendable whip antenna Line (Aux) – Out jack Headphone jack Rx LED indicator Set button ...
-
Page 11: Bodypack Transmitter
WIRELESS ENG / EFP SYSTEM Bodypack Transmitter Whip antenna XLR Microphone jack Talk / Mute switch Line (Aux) – In jack Tx / Talk LED indicator ... -
Page 12: Handheld Microphone
WIRELESS ENG / EFP SYSTEM Handheld microphone optional Dynamic capsule Talk / Mute button Backlit screen Frequency code Battery status RF power Talk mode Mic gain ... -
Page 13: Operation
Do not mistakenly recharge alkaline batteries via charging cable on the device. Okayo will accept no liability for any potential damage due to misuse charging behavior. Press and hold the power button for 1 second to turn the Powering on device on. -
Page 14: Tuning Volume To Appropriate Level
WIRELESS ENG / EFP SYSTEM Bodypack Transmitter Short press the set button to check the frequency of selected channel. Handheld Microphone Short press button to check the frequency of selected channel. Tuning volume to Receiver appropriate level Short press the button to increase volume of channel A but decrease that of channel B and vice versa. -
Page 15: Connecting Correctly To Camera Or Recording
WIRELESS ENG / EFP SYSTEM 3. Default mic gain Mid shows up. Press button to define preferred level. Press the power button to confirm and leave the setting of MIC GAIN. 4. To leave the “setting” mode, press button to find ... -
Page 16: Advanced Operation
WIRELESS ENG / EFP SYSTEM Advanced operation Finding clean channels (SCAN mode) 1. Press and hold both and power button simultaneously to turn the receiver on . shows up. The receiver is at “SCAN” mode. Please wait for appr. 20 seconds until receiver finds clean channels. 3. - Page 17 WIRELESS ENG / EFP SYSTEM 3. After 1 transmitter is paired, “SYNC” will show up on top of Pair 2 transmitter channel B. Turn 2 transmitter on within 20 seconds. pairing Receiver Transmitter Pairing is done 4. When two pairing jobs are done, the receiver will leave SYNC mode and be back to home screen automatically.
-
Page 18: Adjusting Settings
WIRELESS ENG / EFP SYSTEM Adjusting settings 1. Press and hold both set and power buttons simultaneously to turn the receiver module on. (SETTING mode) 2. “Setting” mode will be entered successfully for custom Receiver adjustments. 3. Press button to scroll options. See setting menu ... - Page 19 WIRELESS ENG / EFP SYSTEM Transmitter 1. Press and hold both set and power buttons simultaneously to turn the transmitter on. 2. “Setting” mode will be entered successfully for custom adjustments. 3. Press button to scroll options. See setting menu ...
- Page 20 WIRELESS ENG / EFP SYSTEM Handheld microphone 1. Press and hold both and power buttons simultaneously to turn the microphone on. 2. “Setting” mode will be entered successfully for custom adjustments. 3. Press or button to scroll options. See setting menu below.
-
Page 21: Back To Default
WIRELESS ENG / EFP SYSTEM Back to default 1. When device is off, press and hold and power buttons altogether to turn the receiver, transmitter or microphone on. 2. Device will be back to default settings automatically. 3. Followings list default settings of all Receiver models. Dual-Antenna Channel: 01 ... -
Page 22: Troubleshooting (Not Ready Yet)
WIRELESS ENG / EFP SYSTEM Troubleshooting Not ready... -
Page 23: Specification (Not Ready Yet)
WIRELESS ENG / EFP SYSTEM Specification Not ready...