Page 1
COLOR TELEVISION RECEIVER Chassis : KS3A(P)_100Hz(Rev. 5) Model : CS25M6HN8X/BWT CS29M6HT8X/BWT COLOR TELEVISION RECEIVER CONTENTS Precautions Reference Information Specifications Alignment and Adjustments Troubleshooting Exploded Views and Parts List Electrical Parts List Block Diagrams Wiring Diagram Schematic Diagrams...
Heed the high voltage limits. These include not exceed 0.5 milliamp. Reverse the power- the X–ray Protection Specifications Label, and plug prongs in the AC outlet and repeat the the Product Safety and X-ray Warning Note on test. the service data schematic. Samsung Electronics...
Page 4
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. Samsung Electronics...
Make sure that the portion around 8. Always connect a test instrument’s ground the serviced part has not been damaged. lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. Samsung Electronics...
Page 6
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
Millimeter Hour Millisecond Inches Per Second Millivolt Kilowatt-hour Nanofarad Ω Kilogram Kilohertz Picofarad kΩ Kilohm Pound Kilometer Revolutions Per Minute km/h Kilometer Per Hour Revolutions Per Second Kilovolt Second (Time) Kilovolt-ampere Volt Kilowatt Volt-ampere Liter Watt Megahertz Watt-hour Samsung Electronics...
Page 8
Fail Safe Voltage Controlled Oscillator Ground VCXO Voltage Controlled Crystal Oscillator Green-Y Very High Frequency High Video Intermediate Frequency High-Frequency Variable Resistor HI-FI High Fidelity Video Tape Recorder Inductance-Capacitance VTVM Vacuum Tube Voltmeter Integrated Circuit Transistor Intermediate Frequency Samsung Electronics...
Page 10
Option High-end Picture-In Picture IC SDA9489X Option ICP01 1-TUNER PIP SDA9488 Option ICP0 Option 3.3V Regulator EZ1086CM Table 2-3-1 VIDEO IC (IC201S) REMARK FUNCTION SPEC 100Hz Video Processor VDP3140D DDP3310 Sipadoss Module VPC3230 AA98-00133A(with OKi) AA98-00134B(with SDA9401) SDA9401 Samsung Electronics...
Page 11
TCLS3101PD09A(S) CS with LNA Function Main(Old) TCPS3000P TCPS3001PD09E(S) India CZ, CW TCPW3001PD09A(S) TCLS3101PD16A Main(New) Note TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function. Table 2-3-5 2’nd TUNER (TU02S) REMARK SPEC FUNCTION TCPS3000PC09B(S) Sub(Old() TCPS3000PC16B Sub(New) Samsung Electronics...
Page 12
Reference Information MEMO Samsung Electronics...
2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions. Samsung Electronics...
Page 16
1. Input Toshiba Pattern 2. Enter “Service Mode”.(Refer to “Service Mode”) 3. Select “G2-Adjust”. 4. Set the values as example(Refer to page4-17). ex) IBRM = 220 WDRV = 35 = 220 COLR G B = 150 150 150 Samsung Electronics...
Page 17
For example, when the value of “Red Cutoff” is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually. Samsung Electronics...
7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (L/M) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value. Samsung Electronics...
Page 19
PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select “Reset” in the service mode menu. (After above procedure is done, power is on initially and the “Plug and Play” will be operated.) Samsung Electronics...
Page 20
Corrects the vertical linearity in Zoom mode of P-SIZE. The data 0 ~255 Zoom 4:3 Para depends on CRT (see data above). Corrects the vertical linearity in 16:9 mode of P-SIZE.. 4:3~16:9 Para 0 ~255 The data depends on CRT (see data above). Samsung Electronics...
Page 22
H EW H Corner U H Parabola H Corner L 10 H Shift 11 BOW 12 Angle 13 H Corner U6 14 H Corner L6 15 V Max 16 Zoom Trap 17 Zoom 4:3 Para 18 4:3~10:9 Para Samsung Electronics...
Page 25
OSD jitter may happen. Also, if the value is set between the first andsecond points, a TTX jitter may happen. So, the value of VSU should be set after giving some magines (three steps). EHT Compensation Characteristic Note 4. [kv] EHT compensation 1000 average beam current EHT_THRES Samsung Electronics 4-11...
Page 27
(overmodulation, especially). 0: 100% 1: 90% 2: 75% 3: 60% Sets the level of SECAM Color sensitivity. It improves Hysteresis of APC Pull Color hys 0~255 in range Peaking center frequency switch Auto Color Control gain ACC-Ref Samsung Electronics 4-13...
Page 29
Select TTX On/Off TTX On/Off On : It can select AV Mode for CH key when the number of Pannel key is 5. AV by CH Key Off : In case the AV key is on the panel Samsung Electronics 4-15...
Page 30
AV by CH Key Off : In case that it is AV key in pannel Note 5. Sound IC & System Sound IC601 MSP3400D, MSP3410D A2/NICAM MSP3411G V-DOLBY Mono Not used this mode for KS3A Chassis L-Stereo 4-16 Samsung Electronics...
Page 32
PIP vertical sync pulse delay. When chaning data, PIP jitters at two points. In this case, the PIP VSPDEL is set to the PIP VSPDEL center between two points. Adjusts PIP blanking level green (PIP low light white balance). PIP BLKL G 4-18 Samsung Electronics...
Page 33
OSD-B OSD-G OSD-R Scart1 Ident VDD 2.5V Scart2 Ident Key 1 X-TAL Out H-Sync X-TAL In V-Sync MICOM Reset Key 3 N.C. Key 2 N.C. X-Ray Protect VDD 3.3V IR Input Stand-By LED N.C. Time LED Relay Samsung Electronics 4-19...
Page 35
VDD 2.5V VDD 3.3V PX.Y When The Caption Function Adopted, Used. PX.Y N.C. Not Used (Programmed Gound Level) N.C. Sound Amp Mute S-Mute High Picture On/Off Control Power Not Used (Programmed Gound Level) N.C. Tilt Tilt Control Output Samsung Electronics 4-21...
Page 37
Plug in Power Cord Check LED lamp Check Abnormal Check Normal IC901 MICOM MICOM IIC #5, #6 Input Voltage Normal Abnormal Check and Replace the MICOM Check Level Shifter Q909, Q910 Check Check Normal Normal Abnormal Output(If 2N7000 Output has the DC IC903 3.3V Regulator Check and Replace the MICOM Power #59...
Page 38
No Picture, but sound is in normal operation Turn the VR of FBT, higher screen voltage and Check the Deflection Normal Abnormal is in Normal Operation (If the deflection is in operation, flyback signal is appeared) Check Normal Normal Abnormal Abnormal Check CRT PCB RK, BK, GK...
Page 39
Sound is mute) Normal Check D816, Q906 Check Abnormal IC601 #24, #25 Normal Replace IC602 Check Abnormal IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check Abnormal IC601 Input Signal Normal Check Replace the Tuner IC601 Samsung Electronics...