Table of Contents
Related Manuals for Mitsubishi Electric FR-A7AR
Summary of Contents for Mitsubishi Electric FR-A7AR
- Page 1 INVERTER Plug-in option FR-A7AR FR-A7AR E kit INSTRUCTION MANUAL Relay output function PRE-OPERATION INSTRUCTIONS INSTALLATION AND WIRING (FR-A700/F700 SERIES) INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) RELAY OUTPUT...
- Page 2 Thank you for choosing this Mitsubishi Electric inverter plug-in SAFETY INSTRUCTIONS option. This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might 1. Electric shock prevention cause an unexpected fault. Before using this product, read all WARNING relevant instruction manuals carefully to ensure proper use.
- Page 3 3. Additional instructions CAUTION The following instructions must be also followed. If this product is handled incorrectly, it may cause unexpected fault, an injury, or an As all parameters return to their initial values after Parameter clear electric shock. or All parameter clear is performed, the needed parameters for 1) Transportation and installation operation of the inverter and this product must be set again before...
-
Page 4: Table Of Contents
— CONTENTS — 1 PRE-OPERATION INSTRUCTIONS Unpacking and Product Confirmation .....................1 1.1.1 Packing confirmation (FR-A700/F700 series)....................1 1.1.2 Packing confirmation (FR-E700 series (E kit)) ....................2 Parts ..............................3 Specifications.............................4 2 INSTALLATION AND WIRING (FR-A700/F700 SERIES) Pre-Installation Instructions ......................5 Installation Procedure ........................6 Wiring..............................8 3 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) Pre-Installation Instructions ......................11... - Page 5 APPENDIX Appendix 1 Instructions for compliance with the EU Directives ............26 Appendix 2 Instructions for EAC ......................27 Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products..28 Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ......29...
-
Page 6: Pre-Operation Instructions
PRE-OPERATION INSTRUCTIONS Unpacking and Product Confirmation Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact. This product is a plug-in option dedicated for the FR-A series. 1.1.1 Packing confirmation (FR-A700/F700 series) Check the enclosed items. -
Page 7: Packing Confirmation (Fr-E700 Series (E Kit))
PRE-OPERATION INSTRUCTIONS 1.1.2 Packing confirmation (FR-E700 series (E kit)) Check the enclosed items. Mounting screw (M3 6mm) Plug-in option Front cover for plug-in option ..........1 .... 2 (Refer to page 13, 16) ....1(Refer to page 13, 16) Option protective cover Option small cover Insulation sheet ...... -
Page 8: Parts
PRE-OPERATION INSTRUCTIONS Parts Terminal Mounting Front view Rear view hole block Mounting hole Connector Mounting hole Connect to the inverter option connector 13, 16 (Refer to page Terminal layout... -
Page 9: Specifications
PRE-OPERATION INSTRUCTIONS Specifications (1) Types of output signal 1 changeover contact output (three relays are provided) (2) Contact capacity 230VAC ..0.3A 30VDC .... 0.3A CAUTION • The contacts should be used within the rated capacity to prevent contacts weld resulting from faster contacts wearing. -
Page 10: Installation And Wiring (Fr-A700/F700 Series)
INSTALLATION AND WIRING (FR-A700/F700 SERIES) Pre-Installation Instructions Make sure that the input power of the inverter is off. CAUTION With input power on, do not install or remove the plug-in option. Otherwise, the inverter and plug-in option may be damaged. For prevention of damage due to static electricity, touch nearby metal before touching this product to eliminate static electricity from your body. -
Page 11: Installation Procedure
INSTALLATION AND WIRING (FR-A700/F700 SERIES) Installation Procedure 1)Remove the inverter front cover. 2)Mount the hex-head screw for option mounting into the inverter screw hole (on earth plate). (size 5.5mm, tightening torque 0.56Nm to 0.75Nm) 3)Securely fit the connector of the plug-in Screw hole for option mounting option to the inverter connector along... - Page 12 INSTALLATION AND WIRING (FR-A700/F700 SERIES) CAUTION When used with other plug-in options, always connect the FR-A7AR to the connector 1 to prevent malfunction. Only one type of option per inverter may be used. When two or more options are mounted, priority is in ...
-
Page 13: Wiring
INSTALLATION AND WIRING (FR-A700/F700 SERIES) Wiring (1) Wire the shielded twisted pair cable after stripping its sheath to make its Shield (perform protective treatment) cables loose. Sheath Also, protect the shielded cable of the shielded twisted pair cable to ensure that it will not make contact with the conductive area. Strip the signal wires as shown below. - Page 14 INSTALLATION AND WIRING (FR-A700/F700 SERIES) REMARKS • Information on crimp terminals Commercially available product examples (as of Jan. 2017) Wire gauge Ferrule part No. Terminal Maker screw size With insulation sleeve Without insulation sleeve AI 0,34-6TQ A 0,34-7 Phoenix Contact AI 0,5-6WH A 0,5-6 Co.,Ltd.
- Page 15 INSTALLATION AND WIRING (FR-A700/F700 SERIES) (3) For wiring of the inverter with one front cover, route wires between the control circuit terminal block and front cover. If cables can not be routed between the control circuit terminal block and front cover due to the increased number of cables, remove a hook of the front cover and use a space become available.
-
Page 16: Installation And Wiring (Fr-E700 Series (E Kit))
INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) Pre-Installation Instructions Make sure that the input power of the inverter is off. CAUTION With input power on, do not install or remove the plug-in option. Otherwise, the inverter and plug-in option may be damaged. For prevention of damage due to static electricity, touch nearby metal before touching this product to eliminate static electricity from your body. - Page 17 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) For FR-E720-3.7K (FR-E720-175) or less, FR-E740-7.5K (FR-E740-170) or less (1) Remove the front cover from the inverter. (For removing the front cover, refer to the FR-E700 series instruction manual.) (2) Remove the PU cover from the front cover. Open the PU cover with a driver, etc. and remove it in the direction of arrow as shown below.
- Page 18 (2). (8) When wiring to the plug-in option is completed, install the front cover for plug-in option to the inverter. Insulation sheet (Available only Front cover for FR-A7AR) for plug-in option plug-in option Option connector (7) Replace...
- Page 19 Installation of an insulation sheet For FR-A7AR, put an insulation sheet under the screw platform of inverter (A of the following figure) and fit the insulation sheet to the screw position on the inverter side (B of the following figure).
- Page 20 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) For FR-E720-5.5K (FR-E720-240) or more, FR-E740-11K (FR-E740-230) or more (1) Remove the front cover 1 and 2 from the inverter. (For removing the front cover, refer to the FR-E700 series instruction manual.) (2) Remove the PU cover from the front cover 2.
- Page 21 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) (4) Correctly install the insulating sheet between the inverter and plug-in option. (Refer to page installation method of an insulation sheet.) (5) Securely fit the connector of the plug-in option to the inverter connector along the guides. (6) Securely fix the both top and bottom of the plug-in option to the inverter with the accessory mounting screws.
-
Page 22: Wiring
INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) Wiring (1) Wire the shielded twisted pair cable after stripping its sheath to make its Shield (perform protective treatment) cables loose. Sheath Also, protect the shielded cable of the shielded twisted pair cable to ensure that it will not make contact with the conductive area. - Page 23 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) REMARKS • Information on crimp terminals Commercially available product examples (as of Jan. 2017) Wire gauge Ferrule part No. Terminal Maker screw size With insulation sleeve Without insulation sleeve AI 0,34-6TQ A 0,34-7 Phoenix Contact Al 0,5-6WH A 0,5-6...
- Page 24 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) (3) When wiring the FR-E700 series, if a hook of the front cover for the plug-in option impedes wiring, cut off the hook and perform wiring. Cut off with a nipper, etc. Cut off a hook at the bottom of the option cover.
-
Page 25: Relay Output
You can select any three output signals (RUN, SU, FU, etc.) available with an inverter as standard, and output them as relay contact signals. Refer to page 22, 24 of the Instruction Manual (detailed) for details. The following is the internal block diagram of the FR-A7AR. Connector Controller... -
Page 26: Terminals
RELAY OUTPUT Terminals Terminal Symbol Description Relay RA1's normally open contact terminal Relay RA1's normally closed contact terminal Relay RA1's contact common terminal Relay RA2's normally open contact terminal Relay RA2's normally closed contact terminal Relay RA2's contact common terminal Relay RA3's normally open contact terminal Relay RA3's normally closed contact terminal Relay RA3's contact common terminal... -
Page 27: Output Signal List (Fr-A700/F700 Series)
RELAY OUTPUT Output Signal List (FR-A700/F700 series) For details of signal definitions, refer to Pr. 190 to Pr. 196 (Output terminal function selection) of the inverter (FR-A700/F700 series) manual. Setting Setting Signal Signal Function Positive Function Positive Name Name logic logic Brake opening request Inverter running... - Page 28 RELAY OUTPUT Setting Setting Signal Signal Function Function Positive Positive Name Name logic logic During PID control activated DC current feeding During retry Control circuit capacitor life SLEEP PID output interruption Main circuit capacitor life Commercial-power supply side motor 1 Cooling fan life connection RO1 Inrush current limit circuit life...
-
Page 29: Output Signal List (Fr-E700 Series)
RELAY OUTPUT Output Signal List (FR-E700 series) For details of signal definitions, refer to Pr. 190 to Pr. 192 (Output terminal function selection) of the inverter (FR-E700 series) manual. Setting Setting Signal Signal Function Positive Function Positive Name Name logic logic Fan fault output Inverter running... -
Page 30: Connection Diagram When Using Electronic Bypass Sequence Function (Fr-A700/F700 Series)
Connection Diagram When Using Electronic Bypass Sequence Function (FR-A700/F700 series) When using the electronic bypass sequence function with the FR-A7AR mounted to the FR-A700/F700 series inverter, it is recommended to use either connection shown below. (1) Recommended connection example 1... -
Page 31: Appendix
CE marking. The authorized representative in the EU The authorized representative in the EU is shown below. Name: Mitsubishi Electric Europe B.V. Address: Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Note • To use this product in the EU, the operating capacity of the relay outputs should be 30 VDC, 0.3 A. (Relay output has basic isolation from the inverter internal circuit.) -
Page 32: Appendix 2 Instructions For Eac
9, X (October), Y (November), or Z (December). • Authorized sales representative (importer) in the CU area The authorized sales representative (importer) in the CU area is shown below. Name: Mitsubishi Electric (Russia) LLC Address: 52, bld 1 Kosmodamianskaya Nab 115054, Moscow, Russia Phone: +7 (495) 721-2070... -
Page 33: Appendix 3 Restricted Use Of Hazardous Substances In Electronic And Electrical Products
APPENDIX Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products The mark of restricted use of hazardous substances in electronic and electrical products is applied to the product as follows based on the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products”... -
Page 34: Appendix 4 Referenced Standard (Requirement Of Chinese Standardized Law)
APPENDIX Appendix 4 Referenced Standard (Requirement of Chinese standardized law) This Product is designed and manufactured accordance with following Chinese standards. EMC: GB/T 12668.3 IB(NA)-0600166ENG-E... - Page 35 REVISIONS *The manual number is given on the bottom left of the back cover. Print Date *Manual Number Revision May, 2004 IB(NA)-0600166ENG-A First edition Dec., 2004 IB(NA)-0600166ENG-B Partial modification Board shape change Addition Compatible with the FR-F700-NA series Sep., 2005 IB(NA)-0600166ENG-C Addition Compatible with the FR-A700 series...
- Page 36 INVERTER HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN IB(NA)-0600166ENG-E (1903) MEE Printed in Japan Specifications subject to change without notice.