hit counter code
Sony CDX-M8815X Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. CDX-M8815X - Fm/am Compact Disc Player
  6. Service manual
Sony CDX-M8815X Service Manual

Sony CDX-M8815X Service Manual

Hide thumbs Also See for CDX-M8815X:
Table of Contents

Advertisement

Quick Links

See also: Operating and Installation Instruction
CDX-M8810/M8815X
SERVICE MANUAL
Ver. 1.0 2005.01
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
30 µV
Sensitivity
Sony Corporation
9-879-383-01
2005A04-1
e Vehicle Company
© 2005.01
Published by Sony Engineering Corporation
Photo: CDX-M8810
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
Power amplifier section
Outputs
Speaker impedance
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Tone controls
Loudness
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Note
This unit cannot be connected to a digital preamplifier or an equalizer.
Design and specifications are subject to change without
notice.
FM/AM COMPACT DISC PLAYER
US Model
Canadian Model
CDX-F7715X
MG-611TS-186//K
KSS1000E
Speaker outputs (sure seal connectors)
4 – 8 ohms
Audio output terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input or AUX IN terminal
Remote controller input terminal
Antenna input terminal
Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
+8 dB at 100 Hz
+2 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 184 mm
× 2 × 7
(7
in.) (w/h/d)
1/8
1/4
Approx. 182 × 53 × 162 mm
× 2
× 6
(7
in.) (w/h/d)
1/4
1/8
1/2
Approx. 1.7 kg (3 lb. 12 oz.)
Parts for installation and connections (1 set)
Card remote commander: RM-X143A
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-M8815X

Summary of Contents for Sony CDX-M8815X

  • Page 1 Sensitivity This unit cannot be connected to a digital preamplifier or an equalizer. Design and specifications are subject to change without notice. FM/AM COMPACT DISC PLAYER Sony Corporation 9-879-383-01 2005A04-1 e Vehicle Company © 2005.01 Published by Sony Engineering Corporation...
  • Page 2 REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL IN SUPPLEMENTS PUBLISHED BY SONY. OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 CDX-M8810/M8815X • CD Playback: UNLEADED SOLDER You can play CD-DA (also containing CD TEXT* ), CD-R/CD- Boards requiring use of unleaded solder are printed with the lead RW (MP3 files also containing Multi Session and ATRAC CD free mark (LF) indicating the solder contains no lead. (ATRAC3 and ATRAC3plus format).

  • Page 4: Table Of Contents

    CDX-M8810/M8815X NOTE FOR THE OPENING OF THE FRONT PANEL TABLE OF CONTENTS In this set, the front panel is lowered to below the bottom face when it is opened. 1. GENERAL When servicing the set, place it on a stand having a height of about Location of Controls ..............

  • Page 5: General

    O CLOSE button 5 SOURCE operation is different, see page 12. To close the front panel. *2 When an MD changer is connected. *3 When an optional Sony portable device is P MODE button 8, 12 CLOSE MODE SOUND MENU LIST connected.
  • Page 6 CDX-M8810/M8815X Source selector (not supplied) Sélecteur de source Supplied with the CD/MD changer (non fourni) Fourni avec le changeur de CD/MD XA-C30 BUS AUDIO IN /AUX IN AUDIO OUT REMOTE FRONT RCA pin cord (not supplied) Be sure to match the color- coded cord for audio to the SUB OUT ( MONO ) appropriate jacks from the...

  • Page 7: Disassembly

    CDX-M8810/M8815X SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-1. SCREW (PANEL) (Page 8) 2-2. CD MECHANISM BLOCK (Page 8) 2-3. FRONT PANEL ASSY 2-14. SERVO BOARD 2-8. CHASSIS (T) SUB ASSY (Page 9) (Page 14) (Page 11) 2-4.

  • Page 8: Screw (Panel)

    CDX-M8810/M8815X Note : Follow the disassembly procedure in the numerical order given. 2-1. SCREW (PANEL) 2 screw (panel) 1 screw (panel) front panel assy 2-2. CD MECHANISM BLOCK 8 bracket (CD) 6 CD mechanism block 7 two screws (+PTT 2.6 x 6) 2 screw (+PTT 2.6 x 6) 1 two screws...

  • Page 9: Front Panel Assy

    CDX-M8810/M8815X 2-3. FRONT PANEL ASSY 1 tension spring (FPC) 3 cover (FPC) 2 slider (FPC) slider (FPC) two claws flexible board Note: When installing the flexible board, make the board slack as illustrated. 5 front panel assy 4 CNP909 2-4. SUB PANEL (CD) ASSY two claws two claws 1 CN506...

  • Page 10: Driving Section (Db-A04)

    CDX-M8810/M8815X 2-5. DRIVING SECTION (DB-A04) 2 screw (+PTT 2.6 x 6) 3 screw (+PTT 2.6 x 6) 4 driving section (DB-A04) 1 CN902 2-6. FOLLOW MOVE (A) SERVICE ASSY, DRIVING (A) SERVICE ASSY To install the assembly, turn the can (LA) and align the detent with the holes A .

  • Page 11: Main Board

    CDX-M8810/M8815X 2-7. MAIN BOARD 1 three ground point screws (+PTT 2.6 x 6) 2 two screws (+PTT 2.6 x 8) 3 MAIN board 4 insulating sheet 2-8. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 x 2.2) 1 two screws (+P 1.7 x 2.2) 6 chassis (T) sub assy...

  • Page 12: Roller Arm Assy

    CDX-M8810/M8815X 2-9. ROLLER ARM ASSY 3 washer (1.1-2.5) 5 roller arm assy 4 gear (RA1) 2 spring (RAR) 1 spring (RAL) 2-10. CHASSIS (OP) ASSY qa chassis (OP) assy 0 coil spring (damper) lever (D) 4 washer 1 CN1 (16P) 9 two coil springs (damper) 5 gear (LE1) slider (R)

  • Page 13: Optical Pick-Up

    CDX-M8810/M8815X 2-11. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 x 5) 2-12. SL MOTOR ASSY (M902) 1 screw (+P 1.4 x 1.8) 2 SL motor assy (M902)

  • Page 14: Le Motor Assy (M903)

    CDX-M8810/M8815X 2-13. LE MOTOR ASSY (M903) 8 screw 0 gear (LE) assy (+M 1.7 x 2.5) 9 bearing (LEB-N) 2 washer qa screw (+M 1.7 x 2.5) qf two toothed lock screws 3 gear (LE1) (+M 1.4 ) lever (D) bracket (LEM-N) qs screw qg LE motor assy...

  • Page 15: Diagrams

    CDX-M8810/M8815X SECTION 3 DIAGRAMS 3-1. BLOCK DIAGRAM — CD SECTION — AU+5V AUDIO INTERFACE DETECTOR FPI2 AGCI RFEQO AOUT DATA VOUTL+ RFDCI RFRPI MAIN CD-L FNI2 BCKO VOUTL– SECTION (Page 16) LRCKO LRCK VOUTR+ FPI1 R-CH VOUTR– FNI1 RF AMP,DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR ZEROL 22 DAC ZDETL...

  • Page 16: Block Diagram -Main Section

    CDX-M8810/M8815X 3-2. BLOCK DIAGRAM — MAIN SECTION — ELECTRONIC VOLUME SUB OUT AMP IC401 IC470 (1/2) CN401 42 MDL OUT SW CD-L SECTION SUB OUT (MONO) IC470 (2/2) MUTE (Page 15) 43 MDR R-CH Q470 LINE AMP CREF BUFFER BIAS IC402 JP401 (1/2) PJ401 (2/2)

  • Page 17: Block Diagram -Display Section

    CDX-M8810/M8815X 3-3. BLOCK DIAGRAM — DISPLAY SECTION — SYSTEM CONTROL IC303 (3/3) FL DRIVER SIRCS 1 RECEIVE (IR RECEIVER) IC62 D513 MENU LED_SW3 RECEIVE (IR RECEIVER) ILLUM LED DRIVER IC503 Q906,Q909-915 RING 9 XOUT LED_SW10 ILLUM X301 KEYIN0 85 KEY IN S911-921 32.768MHz MATRIX...

  • Page 18: Circuit Boards Location

    CDX-M8810/M8815X 3-4. CIRCUIT BOARDS LOCATION • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) SENSOR board SERVO board For schematic diagrams.

  • Page 19: Printed Wiring Boards -Cd Mechanism Section

    CDX-M8810/M8815X 3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 18 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor 1-864-900- 1-864-900- Location Ref. No. Location MAIN BOARD CNP301 B-11 (Page 23) CDX-M8810/M8815X...

  • Page 20: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-M8810/M8815X • Refer to page 18 for Waveforms. 3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 31 for IC Block Diagrams. IC B/D C102 TP25 TP26 IC B/D TP27 TP93 TP29 R125 R126 R127 R128 R124 R129 R130...

  • Page 21: Schematic Diagram -Cd Mechanism Section (2/2)

    CDX-M8810/M8815X • Refer to page 18 for Waveform. • Refer to page 32 for IC Block Diagram. 3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 37 for IC Pin Description. (Page 20) (Page 26) TP74 TP88 TP75 TP89...

  • Page 22: Printed Wiring Boards -Main Section

    CDX-M8810/M8815X 3-8. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 18 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location Ref. No. Location D101 D-10 D832 D102 D-10 (D843) D103 D-10 (D904) D104 (D906) D105...
  • Page 23 CDX-M8810/M8815X CNP102 CNP101 PJ501 C211 C210 C205 C215 C227 F901 C228 IC201 CN401 C278 C288 C188 R408 C101 C178 C409 R275 R285 FB402 R175 R185 D402 R184 FB401 TH100 R402 C212 L101 R143 C440 C203 R242 TUX501 R462 Q451 Q103 R110 C438 R435...

  • Page 24: Schematic Diagram -Main Section (1/4)

    CDX-M8810/M8815X 3-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 33 for IC Block Diagrams. R204 R203 C207 C206 R201 C201 C204 R208 C208 C209 C202 R202 C214 C205 C210 C211 C215 C203 C228 C212 C227 IC201 IC B/D CNP101 C216...

  • Page 25: Schematic Diagram -Main Section (2/4)

    CDX-M8810/M8815X 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 34 for IC Block Diagrams. R438 R437 IC B/D R406 C278 R457 C448 R432 R431 R461 Q450 R430 C178 IC431 R429 C273 R274 C288 Q451 R275 C272 R462 PJ401 Q271...

  • Page 26: Schematic Diagram -Main Section (3/4)

    CDX-M8810/M8815X • Refer to page 18 for Waveforms. • Refer to page 34 for IC Block Diagram. 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 39 for IC Pin Description. (Page 24) (Page 25) (Page 21) L303 CNP301 C123...

  • Page 27: Schematic Diagram -Main Section (4/4)

    CDX-M8810/M8815X 3-12. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 34 for IC Block Diagrams. (Page 25) Q503 R532 SW501 R534 R535 R531 R533 (Page 24) D514 D512 Q504 CN501 D513 IC703 S601 R707 R708 R709 C702 CN902 IC B/D (Page 27)

  • Page 28: Printed Wiring Board -Sub Section

    CDX-M8810/M8815X 3-13. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 18 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location D506 D507 D511 D512 D513 G-10 D514 C537 R538 IC503 R509 Q503 CN501 Q504 C538...

  • Page 29: Printed Wiring Board -Display Section

    CDX-M8810/M8815X 3-14. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 18 for Circuit Boards Location. : Uses unleaded solder. LED931 LED943 S920 FMA10 FMA11 R1004 R994 R971 R972 S931 C914 R981 D901 R999 FB913 C908 FB912 R987 Q903 R929 Q904...

  • Page 30: Schematic Diagram -Display Section

    CDX-M8810/M8815X • Refer to page 36 for IC Block Diagram. 3-15. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 41 for IC Pin Description. Q903 R936 R983 R974 R996 R998 R932 R943 R966 R952 R945 R956 R958 R955 R924 R930 R926...

  • Page 31: Ic Block Diagrams

    CDX-M8810/M8815X • IC BLOCK DIAGRAMS IC2 TC94A60MFG-301 (SERVO Board (1/2)) 72 71 66 65 64 63 62 61 60 59 58 56 55 54 53 52 51 SLCO AUDIO DIGITAL VCOI AWRC TMAX VSSP EFM SLICE TESTD RFRP RFRPI REFQO RFEQ RESIN FGIN...
  • Page 32 CDX-M8810/M8815X IC5 PCM1793DBR (SERVO Board (1/2)) FMT2 FMT1 FMT0 DEMP1 DEMP0 SYSTEM CLOCK ZERO ZEROL MANAGER DETECT ZEROR LRCK AUDIO DATA INPUT OVERSAMPLING DATA ADVANCED DIGITAL SEGMENT FILTER MODULATOR MUTE FUNCTION FUNCTION CONTROL CONTROL DGND VCCF POWER SUPPLY AGNDF VCCL VCCR AGNDL AGNDR...
  • Page 33 CDX-M8810/M8815X IC201 TDA8588AJ/N2/R1 (MAIN Board (1/4)) OUT FL- I2C BUS OUT FL+ OUT RL- PGND3 OUT RL+ INRL INFL SGND PROTECTION DIAGNOSTIC INFR INRR AC GND OUT RR+ PGND2 OUT RR- OUT FR+ STANDBY MUTE OUT FR- CHIP DETECT PGND1 DIAGNOSTIC TEMPERATURE DIAG...
  • Page 34 CDX-M8810/M8815X IC402 LA2901V-TLM-E (MAIN Board (2/4)) SIGNAL LFIN- LFOUT LFIN+ VREF SIGNAL LRIN- LROUT LRIN+ LGND VREF LIFT LIFT LIFT LOUT VREF VCCL VCCR VREF LIFT ROUT LIFT LIFT ROUT VREF RGND RFIN+ RFOUT SIGNAL RFIN- VREF RRIN+ RROUT RRIN- SIGNAL IC110 BA8271F-E2 (MAIN Board (3/4)) IC702 LB1930M-TLM-E (MAIN Board (4/4))
  • Page 35 CDX-M8810/M8815X IC401 TDA7416 (MAIN Board (2/4)) 30 29 24 23 HIGH PASS MIXER FILTER2 SOFT STEP FADER ACOUTR SOFT STEP ACINSW FADER ACOUTSW HIGH PASS MIXER 22 OUTRF FILTER WOOFER SOFT STEP OUTRR FILTER FADER 7 BAND EQUALIXER 20 AC2INR HIGH 19 AC2OUTR PASS...
  • Page 36 CDX-M8810/M8815X IC503 RRX9000-0601#1 (SUB Board) IC62 RRX9000-0601#1 (DISPLAY Board) GND A VAGC VCO NC 11 10 INPUT 320kHz NOISE 320kHz PULSE SLAGE /500kHz SUPPRESSION COUNTER PULSE FORMER BANDGAP REFERENCE LIN GND VSTAB IC301 TC74VHC32FT(EL) (DISPLAY Board)
  • Page 37 CDX-M8810/M8815X • IC PIN DESCRIPTIONS • IC3 MB90487APFV-G-142-BNDE1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2)) Pin No. Pin Name Pin Description Servo 1.5 V power supply control signal output 2 to 6 — Not used. (Open) CD BUS0 Bus data signal input/output 0 CD BUS1 Bus data signal input/output 1 —...
  • Page 38 CDX-M8810/M8815X Pin No. Pin Name Pin Description XUART Sony-Bus/MC-Bus change signal input H: Sony-Bus, L: MC-Bus ZMUTE Zero detection mute signal output MECON CHK MECON rising detection signal input CDON CHK CDON rising detection signal input 69 to 74 —...
  • Page 39 CDX-M8810/M8815X • IC303 M30622MEP-186GP (SYSTEM CONTROL) (MAIN Board (3/4)) Pin No. Pin Name Pin Description SIRCS Remote control data input FP_CTRL Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) BYTE L fixed terminal CNVSS Flash write-in signal input Sub clock input (32.768kHz) XOUT Sub clock output (32.768kHz)
  • Page 40 CDX-M8810/M8815X Pin No. Pin Name Pin Description MOTOR ON Front panel motor drive ON signal output CLOSE-SW Front panel close switch signal input OPEN-SW Front panel open switch signal input I_DET Not used. (Open) MOT– Front panel open/close control signal output MOT+ Front panel open/close control signal output CD_ON...
  • Page 41 CDX-M8810/M8815X • IC2 M30843MW-058GP (FL DRIVER) (DISPLAY Board) Pin No. Pin Name Pin Description SYS_CE Main chip enable signal input Not used. (Open) FL_DAT3 FL serial data output Not used. (Open) FL_CLK_IN FL serial clock input BYTE L fixed terminal CNVSS Flash write signal input PLL_LPF...
  • Page 42 CDX-M8810/M8815X Pin No. Pin Name Pin Description LED_SW4 LED driver signal output LED_SW3 LED driver signal output 76 to 93 Not used. (Open) AVSS — Ground Not used. (Open) VREF — Power supply pin (+5V) AVCC — Power supply pin (+5V) RXD1 —...

  • Page 43: Exploded Views

    CDX-M8810/M8815X SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference The components identified by • Color Indication of Appearance Parts mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.

  • Page 44: Main Board Section

    CDX-M8810/M8815X 4-2. MAIN BOARD SECTION not supplied not supplied TUX501 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1087-250-A MAIN BOARD, COMPLETE (M8810) 2-641-447-11 SCREW (2.6X6), + STP A-1091-763-A MAIN BOARD, COMPLETE (M8815X) 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 2-178-992-01 GUIDE (DRIVE SHAFT) (2) 1-790-375-22 CORD (WITH CONNECTOR) (SUB OUT (MONO))

  • Page 45: Front Panel Section

    CDX-M8810/M8815X 4-3. FRONT PANEL SECTION not supplied not supplied FL900 supplied not supplied supplied not supplied LCD2 supplied not supplied supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3384-477-2 PANEL (KEY) ASSY, FRONT 1-780-138-11 CONDUCTIVE BOARD, CONNECTION X-2048-458-1 BUTTON ASSY (S) 3-260-053-01 SHEET (LCD KEY), DIFFUSION...

  • Page 46: Cd Mechanism Section (1)

    CDX-M8810/M8815X 4-4. CD MECHANISM SECTION (1) (MG-611TS-186//K) not supplied (SENSOR board) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-455-A CHASSIS (T) SUB ASSY 3-253-748-01 DAMPER (S) 3-253-729-01 SPRING (LTR), TENSION COIL 3-352-758-31 SCREW (M1.7), TOOTHED LOCK 3-253-746-14 SPRING (DAMPER), COMPRESSION A-1075-811-A SERVO BOARD, COMPLETE...

  • Page 47: Cd Mechanism Section (2)

    CDX-M8810/M8815X 4-5. CD MECHANISM SECTION (2) (MG-611TS-186//K) (including M901) M902 not supplied not supplied not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité.

  • Page 48: Cd Mechanism Section (3)

    CDX-M8810/M8815X 4-6. CD MECHANISM SECTION (3) (MG-611TS-186//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-262-755-01 WASHER (1.1-2.5) 2-186-696-11 BRACKET (LEM-N) 2-186-699-11 GEAR (RA1) 3-345-648-91 SCREW (M1.4), TOOTHED LOCK A-1075-789-A ARM ASSY, ROLLER A-1083-637-A GEAR (LE) ASSY 3-259-455-02 SPRING (RAL) 2-186-697-11 BEARING (LEB-N) 3-253-713-01 SPRING (RAR)

  • Page 49: Cd Mechanism Section (4)

    CDX-M8810/M8815X 4-7. CD MECHANISM SECTION (4) (MG-611TS-186//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-186-700-11 GEAR (CHK1) 3-899-829-01 WASHER (SLIT) 3-344-223-01 WASHER 3-259-032-01 GEAR (LE2) 3-259-470-01 GEAR (LE1) A-1075-791-A CHASSIS (M) BLOCK ASSY 3-253-755-02 LEVER (D)

  • Page 50: Electrical Parts List

    CDX-M8810/M8815X SECTION 5 DISPLAY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 51 CDX-M8810/M8815X DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LED910 8-719-053-09 LED SML-310VTT86 (ATT) (M8810) Q913 8-729-055-94 TRANSISTOR SRC1202SF LED911 6-500-476-01 LED SML310BA1TT86 (OFF) (M8815X) Q914 8-729-055-94 TRANSISTOR SRC1202SF LED911 8-719-053-09 LED SML-310VTT86 (OFF) (M8810) Q915 8-729-055-94 TRANSISTOR SRC1202SF LED912 6-500-476-01 LED SML310BA1TT86 (ENTER) (M8815X)
  • Page 52 CDX-M8810/M8815X DISPLAY MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R955 1-216-033-00 RES-CHIP 1/10W R1002 1-216-053-00 RES-CHIP 1.5K 1/10W (M8815X) (M8810) R955 1-216-037-00 RES-CHIP 1/10W R1004 1-216-845-11 METAL CHIP 100K 1/10W (M8810) R1005 1-216-809-11 METAL CHIP 1/10W R956 1-216-029-00 RES-CHIP...
  • Page 53 CDX-M8810/M8815X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C121 1-162-970-11 CERAMIC CHIP 0.01uF C273 1-126-964-11 ELECT 10uF C123 1-162-970-11 CERAMIC CHIP 0.01uF (M8810) C129 1-126-965-11 ELECT 22uF C274 1-162-970-11 CERAMIC CHIP 0.01uF C142 1-162-927-11 CERAMIC CHIP 100PF C278 1-162-927-11 CERAMIC CHIP...
  • Page 54 CDX-M8810/M8815X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C423 1-162-970-11 CERAMIC CHIP 0.01uF C625 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C424 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C628 1-107-826-11 CERAMIC CHIP 0.1uF C425 1-136-154-00 FILM 0.012uF C629 1-104-665-11 ELECT 100uF...
  • Page 55 CDX-M8810/M8815X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D403 8-719-069-55 DIODE UDZSTE-175.6B < COIL > D501 8-719-069-55 DIODE UDZSTE-175.6B D601 8-719-058-24 DIODE RB501V-40TE-17 L101 1-456-617-11 COIL, CHOKE D602 8-719-058-24 DIODE RB501V-40TE-17 L102 1-414-394-41 INDUCTOR 2.2uH D620 8-719-053-18 DIODE 1SR154-400TE-25...
  • Page 56 CDX-M8810/M8815X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R111 1-216-841-11 METAL CHIP 1/10W R360 1-216-845-11 METAL CHIP 100K 1/10W R112 1-216-821-11 METAL CHIP 1/10W R363 1-216-845-11 METAL CHIP 100K 1/10W R114 1-216-809-11 METAL CHIP 1/10W R364 1-216-845-11 METAL CHIP...
  • Page 57 CDX-M8810/M8815X MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R501 1-216-821-11 METAL CHIP 1/10W SENSOR BOARD R502 1-216-864-11 SHORT CHIP ************** R504 1-216-864-11 SHORT CHIP R507 1-216-843-11 METAL CHIP 1/10W < SWITCH > R508 1-216-839-11 METAL CHIP 1/10W...
  • Page 58 CDX-M8810/M8815X SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-125-777-11 CERAMIC CHIP 0.1uF < RESISTOR > 1-125-837-91 CERAMIC CHIP 6.3V 1-125-777-11 CERAMIC CHIP 0.1uF 1-218-941-81 RES-CHIP 1/16W 1-125-777-11 CERAMIC CHIP 0.1uF 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W 1-125-777-11 CERAMIC CHIP...
  • Page 59 CDX-M8810/M8815X SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-218-973-11 RES-CHIP 1/16W < VIBRATOR > 1-218-941-81 RES-CHIP 1/16W 1-218-941-81 RES-CHIP 1/16W 1-813-371-21 VIBRATOR, CERAMIC (12MHz) 1-218-941-81 RES-CHIP 1/16W ************************************************************* 1-218-941-81 RES-CHIP 1/16W A-1091-765-A SUB BOARD, COMPLETE 1-218-973-11 RES-CHIP 1/16W ********************...
  • Page 60 CDX-M8810/M8815X Ref. No. Part No. Description Remark MISCELLANEOUS *************** 1-776-207-72 CORD (WITH CONNECTOR) (POWER) 1-790-375-22 CORD (WITH CONNECTOR) (SUB OUT (MONO)) 1-861-811-11 FLEXIBLE BOARD 0 203 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP) A-1075-787-A CHASSIS (OP) SUB ASSY (including M901) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A M902 A-3337-638-A MOTOR ASSY, SL (SLED) M903...
  • Page 61 CDX-M8810/M8815X MEMO...
  • Page 62 CDX-M8810/M8815X REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2005.01...

This manual is also suitable for:

Cdx-m8810

Table of Contents