Page 2 Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
Page 3: Table Of Contents
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Table of Contents Introduction ................................1 Intended Readers ..............................1 Other Documentation .............................. 1 Typographical Conventions ............................ 1 Notes and Cautions ..............................1 Web-based Switch Configuration ........................2 Management Options .............................
Page 4 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SNMP Community Table Settings ........................35 SNMP Group Table Settings ........................... 36 SNMP Engine ID Local Settings ........................37 SNMP User Table Settings ..........................37 SNMP Host Table Settings ..........................39 RMON ...................................
Page 5 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide MAC Address Table ............................105 MAC Notification ............................105 VLAN ................................... 107 802.1Q VLAN ..............................107 802.1v Protocol VLAN ........................... 107 GVRP ................................109 Asymmetric VLAN ............................112 MAC VLAN ..............................
Page 6 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Proxy ARP ..............................191 ARP Table ..............................192 Gratuitous ARP ..............................192 IPv6 Neighbor ..............................193 Interface ................................194 IPv4 Interface ..............................194 IPv6 Interface ..............................196 Loopback Interface ............................
Page 7 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide CoS Color Mapping ............................234 DSCP Color Mapping ............................ 235 Class Map ..............................236 Aggregate Policer ............................237 Policy Map ..............................241 Policy Binding ..............................244 QoS PFC ................................245 Network QoS Class Map ..........................
Page 8 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide 802.1X Global Settings ..........................301 802.1X Port Settings ............................301 Authentication Sessions Information ......................302 Authenticator Statistics ..........................303 Authenticator Session Statistics ........................304 Authenticator Diagnostics ..........................304 AAA ..................................
Page 9 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Host Key ................................ 361 SSH Server Connection ..........................362 SSH User Settings ............................363 SSL ..................................363 SSL Global Settings ............................364 Crypto PKI Trustpoint ............................ 365 SSL Service Policy ............................
Page 10 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Green .................................. 415 Power Saving ..............................415 EEE ..................................416 Save and Tools ..............................418 Save Configuration ............................. 418 Firmware Upgrade & Backup..........................418 Firmware Upgrade from HTTP ........................418 Firmware Upgrade from TFTP ........................
Page 11: Introduction
The documents below are a further source of information in regards to configuring and troubleshooting the Switch. All the documents are available either from the CD, bundled with the Switch, or from the D-Link website. Other documents related to the Switch are: •...
Page 12: Web-Based Switch Configuration
Alternatively, the Switch can also be managed, in-band, by using a Telnet connection to any of the LAN ports on the Switch. The command line interface provides complete access to all Switch management features. For more detailed information about the CLI, refer to the DXS-3400 Series CLI Reference Guide. SNMP-based Management The Switch can be managed with an SNMP-compatible console program.
Page 13: Web User Interface (Web Ui)
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After pressing the ENTER key, the following authentication window should appear, as shown below. Figure 2-2 Web UI Login Window When connecting to the Web UI of the Switch for the first time, leave the User Name and Password fields blank and click Login since there are no login user accounts created by default on the Switch.
Page 14 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide AREA 1 AREA 2 AREA 3 AREA 4 Figure 2-3 Main Web UI Window Area Number Description AREA 1 This area displays a graphical, near real-time image of the front panel of the Switch.
Page 15: System
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide System Device Information System Information Settings Peripheral Settings Port Configuration Loopback Test System Log Time and SNTP Time Range PTP (Precise Time Protocol) USB Console Settings Device Information In the Device Information section, the user can view a list of basic information regarding the Switch.
Page 16: Peripheral Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-2 System Information Settings Window The fields that can be configured in System Information Settings are described below: Parameter Description System Name Enter a system name for the Switch, if so desired. This name will identify it in the Switch network.
Page 17: Port Configuration
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-3 Peripheral Settings Window The fields that can be configured in Environment Trap Settings are described below: Parameter Description Fan Trap Click to enable or disable the fan trap state for warning fan event (fan failed or fan recover).
Page 18 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-4 Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be configured here.
Page 19 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description is in the MDI mode and can be connected to a port (in the MDIX mode) on another switch through a straight cable. Flow Control Select to either turn flow control On or Off here.
Page 20: Port Status
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: When the state of a combo port is enabled/disabled, regardless of the Medium Type selected, both the RJ45 and SFP ports will be enabled/disabled. Port Status This window is used to display the Switch’s physical port status and settings.
Page 21: Port Auto Negotiation
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-6 Port GBIC Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this display here.
Page 22: Error Disable Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-7 Port Auto Negotiation Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be displayed here.
Page 23: Jumbo Frame
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-8 Error Disable Settings Window The fields that can be configured are described below: Parameter Description ErrDisable Cause Select the error disabled cause here. Options to choose from are Port Security, Storm Control, BPDU Attack Protection, Dynamic ARP Inspection, DHCP Snooping, and Loopback Detect.
Page 24: Loopback Test
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-9 Jumbo Frame Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be configured here.
Page 25 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-10 Loopback Test Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 26: System Log
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. System Log System Log Settings This window is used to display and configure the system’s log settings. To view the following window, click System > System Log > System Log Settings, as shown below:...
Page 27: System Log Discriminator Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description interfaces this value is from 1 to 4094. Click the Apply button to accept the changes made. The fields that can be configured for Buffer Log Settings are described below:...
Page 28: System Log Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-12 System Log Discriminator Settings Window The fields that can be configured are described below: Parameter Description Discriminator Name Enter the discriminator name here. This name can be up to 15 characters long.
Page 29: System Log
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Host IPv4 Address Enter the system log server’s IPv4 address here. Host IPv6 Address Enter the system log server’s IPv6 address here.
Page 30: Time And Sntp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-15 System Attack Log Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be displayed here.
Page 31 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 3-17 Time Zone Settings Window The fields that can be configured are described below: Parameter Description Summer Time State Select the summer time setting. Options to choose from are Disabled, Recurring Setting, and Date Setting.
Page 32: Sntp Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description To: Week of the Month Select week of the month that summer time will end. To: Day of the Week Select the day of the week that summer time will end.
Page 33: Time Range
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Poll Interval Enter the synchronizing interval in seconds. The value is from 30 to 99999 seconds. The default interval is 720 seconds. Click the Apply button to accept the changes made.
Page 34: Ptp (Precise Time Protocol)
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Delete button to delete the specified entry. PTP (Precise Time Protocol) PTP Global Settings This window is used to display and configure the Precise Time Protocol (PTP) feature’s global settings.
Page 35: Srm
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SRM Prefer Current Settings This window is used to display and configure the Switch Resource Management (SRM) settings. This window is used to specify the SRM mode to be used on the Switch for optimizing resources for various functions.
Page 36 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description SRM Prefer Mode Select the SRM prefer mode that will be used in the display here. Options to choose from are LAN, IP, and L2VPN.
Page 37: Management
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Management Command Logging User Account Settings Password Encryption Password Recovery Login Method SNMP RMON Telnet/Web Session Timeout DHCP DHCP Auto Configuration IP Source Interface File System Stacking...
Page 38 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: By default, there is no user account created on the Switch. To view the following window, click Management > User Account Settings, as shown below: After selecting the User Management Settings tab, the following page will appear.
Page 39: Password Encryption
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Password Encryption This window is used to display and configure whether to save the encryption of the password in the configuration file. To view the following window, click Management > Password Encryption, as shown below:...
Page 40: Login Method
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Login Method This window is used to display and configure the login method for each management interface that this Switch supports. To view the following window, click Management > Login Method, as shown below:...
Page 41: Snmp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Application Select the application that will be configured here. Options to choose from are Console, Telnet and SSH. Password Type Select the password encryption type that will be used here. Options to choose from are Plain Text and Encrypted.
Page 42: Snmp Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Traps are messages that alert network personnel of events that occur on the Switch. The events can be as serious as a reboot (someone accidentally turned OFF the Switch), or less serious like a port status change. The Switch generates traps and sends them to the trap recipient (or network manager).
Page 43: Snmp Linkchange Trap Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description sending the SNMP trap packet. The fields that can be configured in Trap Settings are described below: Parameter Description Trap Global State Select this option to enable or disable the sending of all or specific SNMP notifications.
Page 44: Snmp View Table Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description that is generated by the system. Trap State Select this option to enable or disable the SNMP link change trap. Click the Apply button to accept the changes made.
Page 45: Snmp Community Table Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SNMP Community Table Settings This window is used to create an SNMP community string to define the relationship between the SNMP manager and an agent. The community string acts like a password to permit access to the agent on the Switch. One or more of the following characteristics can be associated with the community string: •...
Page 46: Snmp Group Table Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SNMP Group Table Settings An SNMP Group created with this table maps SNMP users (identified in the SNMP User Table) to the views created in the previous window.
Page 47: Snmp Engine Id Local Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Delete button to remove the specified entry. SNMP Engine ID Local Settings The Engine ID is a unique identifier used for SNMP V3 implementations on the Switch.
Page 48 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Group Name Enter the SNMP group name to which the user belongs. The syntax is general string that does not allow spaces. SNMP Version Select the SNMP version. Options to choose from are v1, v2c, and v3.
Page 49: Snmp Host Table Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SNMP Host Table Settings This window is used to display and configure the recipient of the SNMP notification. To view the following window, click Management > SNMP > SNMP Host Table Settings, as shown below:...
Page 50: Rmon
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide RMON RMON Global Settings This window is used to enable or disable remote monitoring (RMON) for the rising and falling alarm trap feature for the SNMP function on the Switch.
Page 51: Rmon History Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Show Detail button, the following window will appear.
Page 52: Rmon Alarm Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-19 RMON History Settings (Show Detail) Window Click the Back button to return to the previous window. RMON Alarm Settings This window is used to display and configure alarm entries to monitor an interface.
Page 53: Rmon Event Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide RMON Event Settings This window is used to display and configure event entries. To view the following window, click Management > RMON > RMON Event Settings, as shown below:...
Page 54: Telnet/Web
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Telnet/Web This window is used to display and configure Telnet and Web settings on the Switch. To view the following window, click Management > Telnet/Web, as shown below:...
Page 55: Session Timeout
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Session Timeout This window is used to display and configure the session timeout settings. To view the following window, click Management > Session Timeout, as shown below:...
Page 56: Dhcp Class Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Service DHCP State Select this option to enable or disable the DHCP relay and server service. Click the Apply button to accept the changes made.
Page 57: Dhcp Server
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Option Enter the DHCP option number. The range is from 1 to 255. Enter the hex pattern of the specified DHCP option. Tick the * check box not to match the remaining bits of the option.
Page 58: Dhcp Server Pool Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in DHCP Server Settings are described below: Parameter Description DHCP Ping Packet Enter the number of ping packets that the Switch will send out on the network containing the IP address to be allotted.
Page 59 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-30 DHCP Server Pool Settings (Edit Class) Window The fields that can be configured are described below: Parameter Description Class Name Select an existing DHCP class’ name here that will be associated with this DHCP pool.
Page 60 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description be entered. Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. Click the Back button to return to the previous window.
Page 61: Dhcp Server Manual Binding
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description m-node system broadcasts first, and then queries the name server. A hybrid system queries the name server first, and then broadcasts. Lease Enter and select the lease time for an IPv4 address that is assigned from the address pool here.
Page 62: Dhcp Server Dynamic Binding
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-34 DHCP Server Manual Binding Window The fields that can be configured are described below: Parameter Description Pool Name Enter the DHCP server’s pool name here. This name can be up to 32 characters long.
Page 63 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Clear button to clear the entries based on the information specified. DHCP Server IP Conflict This window is used to display and clear the DHCP conflict entries from the DHCP server database.
Page 64: Dhcpv6 Server
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-37 DHCP Server Statistic Window Click the Clear button to clear the statistics information displayed here. DHCPv6 Server DHCPv6 Server Pool Settings This window is used to display and configure the DHCPv6 server pool settings.
Page 65 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Configure button, the following page will appear.
Page 66 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Valid Lifetime Enter the valid lifetime value here. The valid lifetime should be greater than the preferred lifetime. The range is from 60 to 4294967295 seconds. By default, this value is 2592000 seconds (30 days).
Page 67 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Exclude Address, as shown below: Figure 4-41 DHCPv6 Server Exclude Address Window...
Page 68: Dhcp Relay
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Interface Settings, as shown below: Figure 4-43 DHCPv6 Server Interface Settings Window...
Page 69 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Global Settings, as shown below: Figure 4-45 DHCP Relay Global Settings Window...
Page 70 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-47 DHCP Relay Pool Settings (Source Edit) Window The fields that can be configured are described below: Parameter Description Source IP Address Enter the source subnet of client packets.
Page 71 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-49 DHCP Relay Pool Settings (Class Edit) Window The fields that can be configured are described below: Parameter Description Class Name Select the DHCP class name.
Page 72 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-51 DHCP Relay Information Settings Window The fields that can be configured are described below: Parameter Description Information Trust All Select this option to enable or disable the DHCP relay agent to trust the IP DHCP relay information for all interfaces.
Page 73 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-52 DHCP Relay Information Option Format Settings Window The fields that can be configured in DHCP Relay Information Option Format Global are described below: Parameter Description Select the DHCP information remote ID sub-option.
Page 74 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. DHCP Relay Information Profile Settings This window is used to display and configure the DHCP relay information profile settings.
Page 75 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Profile Name Enter the Option 82 profile name here. The profile can be used to define the flexible user-defined Option 82 entry. Format String After clicking the Edit button, enter the user-defined DHCP Option 82 format string here.
Page 76 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description string or a hexadecimal value.  svlan - Indicates the outer VLAN ID. This can be either an ASCII string or a hexadecimal value. ...
Page 77: Dhcpv6 Relay
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide DHCPv6 Relay DHCPv6 Relay Global Settings This window is used to display and configure the DHCPv6 relay remote ID settings. To view the following window, click Management > DHCP > DHCPv6 Relay > DHCPv6 Relay Global Settings, as...
Page 78 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-56 DHCPv6 Relay Interface Settings Window The fields that can be configured are described below: Parameter Description Interface VLAN Enter the interface’s VLAN ID used in the DHCPv6 relay here. The range is from 1 to 4094.
Page 79: Dhcp Auto Configuration
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Option 18 to the request packets from the client. If the Option 37 check state is enabled, the Switch will check the request packet from the client and drop the packet if it contains Option 37 as specified in the DHCPv6 relay function.
Page 80: Dns Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide name, it determines what type of name resolution the client requested. A complete translation is called recursive resolution and requires the server to contact other DNS servers until the name is resolved. Iterative resolution specifies that if the DNS server cannot supply an answer, it returns the address of the next DNS server the client should contact.
Page 81: Dns Host Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Name Server IPv4 Select and enter the IPv4 address of the DNS server. Name Server IPv6 Select and enter the IPv6 address of the DNS server.
Page 82 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-62 NTP Global Settings Window The fields that can be configured in NTP State are described below: Parameter Description NTP State Select to globally enable or disable the NTP feature here.
Page 83: Ntp Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NTP Server Settings This window is used to display and configure the NTP server settings. This is used to enable the Switch to synchronize the time with an NTP server.
Page 84: Ntp Access Group Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-64 NTP Peer Settings Window The fields that can be configured are described below: Parameter Description IP Address Select and enter the IPv4 address of the NTP peer here.
Page 85: Ntp Key Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-65 NTP Access Group Settings Window The fields that can be configured are described below: Parameter Description Default Select this option to specify to use the default IPv4 (0.0.0.0/0.0.0.0) or IPv6 (::/::) address.
Page 86: Ntp Interface Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-66 NTP Key Settings Window The fields that can be configured in NTP Control Key are described below: Parameter Description NTP Control Key Enter the NTP control key here. This is used to define the key ID for the NTP control messages.
Page 87: Ntp Associations
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Management > NTP > NTP Interface Settings, as shown below: Figure 4-67 NTP Interface Settings Window The fields that can be configured are described below:...
Page 88: Ntp Status
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-69 NTP Associations (Show Detail) Window NTP Status This window is used to display NTP status information. To view the following window, click Management > NTP > NTP Status, as shown below:...
Page 89 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-71 IP Source Interface Window The fields that can be configured in IP TFTP Source Interface are described below: Parameter Description Source Interface State Select to enable or disable the IP TFTP source interface’s state here.
Page 90: File System
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide File System This window is used to display, manage and configure the Switch’s file system. To view the following window, click Management > File System, as shown below:...
Page 91: Stacking
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: If the boot configuration file is damaged, the Switch will automatically revert back to the default configuration. NOTE: If the boot image file is damaged, the Switch will automatically use the backup image file in the next boot up.
Page 92 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Switches in the series can be physically stacked using standard Category 6a cables with RJ45 connectors, optical fiber cables connected to SFP+ transceivers, or Direct Attached Cables (DAC) with SFP+ connectors. Only the last 4 ports can be used for physical stacking.
Page 93 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-77 Duplex Ring stacking topology (RJ45) The figure below illustrates how Switches can be stacked in a Duplex Ring formation using optical fiber cables connected to SFP+ transceivers or Direct Attached Cables (DAC) with SFP+ connectors where the 2-port stacking configuration is used.
Page 94 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide this Switch the highest priority (a lower number denotes a higher priority) before physically assembling the stack, or it can be determined automatically by the stack through an election process which determines the lowest MAC address and then will assign that Switch as the Primary Master, if all priorities are the same.
Page 95: Physical Stacking
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide dynamically learned databases, such as ARP, will be cleared as well. The new Primary Master will inherit the MAC and IP address of the previous Primary Master to avoid conflict within the stack and the network itself.
Page 96: Stacking Bandwidth
Click the Apply button to accept the changes made. Virtual Stacking (SIM) D-Link Single IP Management (SIM) is a concept that will stack Switches together over Ethernet instead of using stacking ports or modules. There are some advantages in implementing the Single IP Management feature:...
Page 97 Switches using D-Link Single IP Management (labeled here as SIM) must conform to the following rules: • SIM is an optional feature on the Switch and can easily be enabled or disabled through the Command Line Interface or Web Interface.
Page 98: Single Ip Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide • The CaS can be configured through the CS to become a MS. After configuring one Switch to operate as the CS of a SIM group, additional Switches may join the group by manually configuring the Switch to be a MS.
Page 99 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-81 Single IP Settings Window The fields that can be configured in SIM State Configure are described below: Parameter Description SIM State Select this option to enable or disable the SIM state on the Switch. Select Disabled to render all SIM functions on the Switch inoperable.
Page 100: Topology
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After enabling the Switch to be a Commander Switch (CS), the Single IP Management folder will then contain four added links to aid the user in configuring SIM through the web, including Topology, Firmware Upgrade, Configuration Backup/Restore and Upload Log File.
Page 101 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Speed Display the connection speed between the CS and the MS or CaS. Remote Port Display the number of the physical port on the MS or CaS to which the CS is connected.
Page 102 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Icon Description Icon Description Layer 2 member Switch Unknown device Non-SIM devices Tool Tips In the Topology view window, the mouse plays an important role in configuration and in viewing device information.
Page 103 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-86 Right-Clicking a Group Icon The following options may appear for the user to configure: • Collapse - To collapse the group that will be represented by a single icon.
Page 104 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Close button to close the property window. Commander Switch Icon Figure 4-88 Right-clicking a Commander Icon The following options may appear for the user to configure: •...
Page 105 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide • Add to group - Add a candidate to a group. Clicking this option will reveal the following dialog box for the user to enter a password for authentication from the Candidate Switch before being added to the SIM group. Click OK to enter the password or Cancel to exit the dialog box.
Page 106: Firmware Upgrade
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-94 About Window Firmware Upgrade This window is used to display and upgrade firmware from the Commander Switch to the Member Switch. Member Switches will be listed in the table To view the following window, click Management >...
Page 107: Upload Log File
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-96 Configuration File Backup/Restore Window The fields that can be configured are described below: Parameter Description TFTP Server IP Enter the TFTP server IP address. Path \ Filename Enter the path and file name.
Page 108 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 4-98 D-Link Discovery Protocol Window The fields that can be configured in D-Link Discovery Protocol are described below: Parameter Description D-Link Discovery Protocol Select to globally enable or disable the DDP feature here.
Page 109: Smtp Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide SMTP Settings This window is used to display and configure the Simple Mail Transfer Protocol (SMTP) settings. To view the following window, click Management > SMTP Settings, as shown below:...
Page 110: Nlb Fdb Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Add A Mail Receiver Enter the email address of the receiver here. This string can be up to 254 characters long. Click the Add button to add a new SMTP email recipient.
Page 111 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description configuration here. MAC Address Enter the unicast or multicast MAC address of the entry here. If a received packet contains a destination MAC address that matches the specified MAC address, it will be forwarded to the specified interface.
Page 112: Layer 2 Features
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Layer 2 Features VLAN VLAN Tunnel ERPS (G.8032) Loopback Detection Link Aggregation L2 Protocol Tunnel L2 Multicast Control LLDP Static FDB Unicast Static FDB This window is used to display and configure the static unicast forwarding settings on the Switch.
Page 113: Mac Address Table Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Multicast Static FDB This window is used to display and configure the multicast static FDB settings. To view the following window, click L2 Features > FDB > Static FDB > Multicast Static FDB, as shown below:...
Page 114 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. After selecting the MAC Address Port Learning Settings tab option, at the top of the page, the following page will be available.
Page 115: Mac Address Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description series of VLAN IDs can be entered separated by commas or a range of VLAN IDs can be entered separated by a hyphen. Status Select to enable or disable the MAC address learning function on the VLAN(s) specified here.
Page 116 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-7 MAC Notification (MAC Notification Settings) Window The fields that can be configured are described below: Parameter Description MAC Address Notification Select to enable or disable MAC notification globally on the Switch Interval Enter the time value between notifications.
Page 117: Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide VLAN 802.1Q VLAN This window is used to display and configure the VLAN settings on the Switch. To view the following window, click L2 Features > VLAN > 802.1Q VLAN, as shown below: Figure 5-9 802.1Q VLAN Window...
Page 118 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-10 Protocol VLAN Profile Window The fields that can be configured are described below: Parameter Description Profile ID Enter the 802.1v protocol VLAN profile ID here. This value must be between 1 and 16.
Page 119: Gvrp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description configured here. Profile ID Select the 802.1v protocol VLAN profile ID here. Enter the VLAN ID used here. Priority Select the priority value used here. This value is between 0 and 7. This parameter is specified to re-write the 802.1p default priority previously set in the Switch,...
Page 120 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-13 GVRP Port Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 121 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-14 GVRP Advertise VLAN Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 122: Asymmetric Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description From Port ~ To Port Select the range of ports that will be used for this configuration here. Action Select the forbidden VLAN to port mapping action that will be taken here. Options to choose from are All, Add, Remove and Replace.
Page 123: Mac Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-17 Asymmetric VLAN Window The fields that can be configured are described below: Parameter Description Asymmetric VLAN State Select to enable or disable the asymmetric VLAN feature here.
Page 124 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-19 VLAN Interface Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 125 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-21 VLAN Interface (Access) Window The fields that can be configured are described below: Parameter Description Select the VLAN mode option here. Options to choose from are Access, Hybrid, VLAN Mode Trunk, 802.1Q-Tunnel, Promiscuous, Host, Trunk Promiscuous, and Trunk...
Page 126 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Secondary. Acceptable Frame Select the acceptable frame behavior option here. Options to choose from are Tagged Only, Untagged Only, and Admit All. Ingress Checking Select to enable or disable the ingress checking function.
Page 127 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description After ticking the Native VLAN option the following parameter will be available. Enter the VLAN ID used for this configuration here. This value must be between 1 and 4094.
Page 128 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Back button to discard the changes made and return to the previous page. When Promiscuous was selected as the VLAN Mode, the following page will appear.
Page 129 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Clone Select this option to enable the clone feature. From Port ~ To Port Select the range of ports that will be used in the clone feature here.
Page 130: L2Vlan Interface Description
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-28 VLAN Interface (Trunk Secondary) Window The fields that can be configured are described below: Parameter Description VLAN Mode Select the VLAN mode option here. Options to choose from are Access, Hybrid, Trunk, 802.1Q-Tunnel, Promiscuous, Host, Trunk Promiscuous, and Trunk...
Page 131: Subnet Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-29 L2VLAN Interface Description Window The fields that can be configured are described below: Parameter Description L2VLAN Interface Enter the ID of the Layer 2 VLAN interface here.
Page 132: Auto Surveillance Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Length here. IPv6 Network Prefix / Prefix Select and enter the IPv6 address and prefix length value for the subnet VLAN Length here. Enter the VLAN ID for the subnet VLAN here.
Page 133 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Aging Time Enter the aging time value here. This is used to configure the aging time for aging out the surveillance VLAN dynamic member ports. The range is from 1 to 65535 minutes.
Page 134: Voice Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description VMS client. • Video Encoder - Specifies the surveillance components type as Video Encoder. • Network Storage - Specifies the surveillance components type as Network Storage.
Page 135 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-34 Voice VLAN Global Window The fields that can be configured are described below: Parameter Description Voice VLAN State Select to globally enable or disable the voice VLAN feature here.
Page 136: Voice Vlan Oui
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port ~ To Port Select the range of ports that will be used for this configuration here.
Page 137 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-36 Voice VLAN OUI Window The fields that can be configured are described below: Parameter Description Enter the voice VLAN OUI MAC address here. OUI Address Mask Enter the matching bitmask for the voice VLAN OUI MAC address here.
Page 138: Private Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Voice VLAN LLDP-MED Device This window is used to display the voice VLAN LLDP-MED device table. To view the following window, click L2 Features > VLAN > Voice VLAN > Voice VLAN LLDP-MED Device, as...
Page 139: Vlan Tunnel
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description VID List Enter the private VLAN ID list here. Action Select the action that will be taken for the private VLAN here. Options to choose from are Add, Remove, and Disabled.
Page 140 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-40 Dot1q Tunnel Settings Window The fields that can be configured are described below: Parameter Description Inner TPID Enter the inner TPID value here. This value is in the hexadecimal form. The range is from 0x1 to 0xFFFF.
Page 141: Vlan Mapping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch’s unit ID that will be used here. From Port ~ To Port Select the Switch’s port range that will be used here.
Page 142: Vlan Mapping Profile
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Original Inner VID Enter the original inner VLAN’s ID here. The range is from 1 to 4094. Action Select the action that will be taken here. Options to choose from are Translate and Dot1q-tunnel.
Page 143 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • IPv6 - The profile can match IPv6 destination or source addresses. Click the Add Profile button to add a new VLAN mapping profile. Click the Find button to locate a specific entry based on the information entered.
Page 144 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description was selected as the action. Click the Back button to return to the previous window. Click the Apply button to accept the changes made. After clicking the Add Rule button next to an IP type profile, the following page will appear.
Page 145 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After clicking the Add Rule button next to an IPv6 type profile, the following page will appear. Figure 5-46 VLAN Mapping Profile (IPv6, Add Rule) Window The fields that can be configured are described below:...
Page 146 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-47 VLAN Mapping Profile (Ethernet-IP, Add Rule) Window The fields that can be configured are described below: Parameter Description Enter the VLAN mapping rule’s ID here. If not specified, the rule ID begins from Rule ID 10 and is incremented by 10 for every new rule.
Page 147: Stp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description New Inner VID After selecting Dot1q-Tunnel as the action, enter the new inner VLAN’s ID here. The range is from 1 to 4094. This option is only available when Dot1q-Tunnel was selected as the action.
Page 148 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured for STP Mode are described below: Parameter Description STP Mode Select the STP mode used here. Options to choose from are MSTP, RSTP, and STP.
Page 149: Stp Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide STP Port Settings This window is used to display and configure the STP port settings. To view the following window, click L2 Features > STP > STP Port Settings, as shown below:...
Page 150: Mst Configuration Identification
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description delay. If the interface receives a BPDU later, its operation state changes to the non-port-fast state. By default, this option is Network. TCN Filter Select to enable or disable the TCN filter option. Enabling TC filtering on a port is...
Page 151: Stp Instance
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-50 MST Configuration Identification Window The fields that can be configured for MST Configuration Identification are described below: Parameter Description Configuration Name Enter the MST. This name uniquely identifies the MSTI (Multiple Spanning Tree Instance).
Page 152: Mstp Port Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click L2 Features > STP > STP Instance, as shown below: Figure 5-51 STP Instance Window The fields that can be configured are described below:...
Page 153: Erps (G.8032)
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Clear Detected Protocol button to clear the detected protocol settings for the port selected. Click the Find button to locate a specific entry based on the information entered.
Page 154 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-54 ERPS (Edit Ring) Window The fields that can be configured are described below: Parameter Description Instance ID Select the checkbox and enter the ERP instance number here. This value must be between 1 and 32.
Page 155 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-55 ERPS (View Detail) Window Click the Back button to return to the previous window. After selecting the ERPS Brief tab option, at the top of the page, the following page will be available.
Page 156 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Description Select the checkbox and enter the ERP instance’s description here. This description can be up to 64 characters long. Select the Specify radio button to configure this parameter as per normal.
Page 157: Erps Profile
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description the None radio button to revert this parameter to the default setting. Activate Select the checkbox and then select whether or not to active this ERP instance.
Page 158: Loopback Detection
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-58 ERPS Profile (Edit) Window The fields that can be configured are described below: Parameter Description TCN Propagation Select the checkbox and then select the TCN propagation state. Options to choose from are Enable and Disabled.
Page 159 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-59 Loopback Detection Window The fields that can be configured in Loopback Detection Global Settings are described below: Parameter Description Loopback Detection State Select to enable or disable loopback detection. The default is Disabled.
Page 160: Link Aggregation
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The Switch supports up to 32 port trunk groups with up to 8 ports in each group.
Page 161 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: If any ports within the trunk group become disconnected, packets intended for the disconnected port will be load shared among the other linked ports of the link aggregation group.
Page 162: L2 Protocol Tunnel
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Delete Channel button to delete the specified channel group. Click the Show Detail button to view more detailed information about the channel. After clicking the Show Detail button, the following page will be available.
Page 163 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-63 L2 Protocol Tunnel (L2 Protocol Tunnel Global Setting) Window The fields that can be configured are described below: Parameter Description CoS for Encapsulated Select the CoS value for encapsulated packets here. This value is between 0 and Packets 7.
Page 164: L2 Multicast Control
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Protocol MAC After selecting the Protocol MAC option as the Tunneled Protocol, the following option will be available. Select the protocol MAC option here. Options to choose from are 01-00-0C-CC-CC-CC and 01-00-0C-CC-CC-CD.
Page 165 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Enter a VLAN ID from 1 to 4094, and select to enable or disable IGMP snooping on the VLAN. Click the Apply button to accept the changes made.
Page 166 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-67 IGMP Snooping Settings (Modify, Edit) Window The fields that can be configured are described below: Parameter Description Minimum Version Select the minimum IGMP host version that is allowed on the VLAN. Options to choose from are 1, 2, and 3.
Page 167 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Rate Limit Enter the rate limit value here. The range is from 1 to 1000. Tick the No Limit option to apply no rate limit on this profile.
Page 168 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IGMP Snooping Groups Settings This window is used to display and configure and view the IGMP snooping static group, and view IGMP snooping group. To view the following window, click L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping...
Page 169 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Show All button to view all the entries. IGMP Snooping Filter Settings This window is used to display and configure the IGMP snooping feature’s filter settings.
Page 170 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in IGMP Snooping Limit Settings are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 171 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Show Detail button, the following page will appear.
Page 172 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Delete button to remove the specified entry. The fields that can be configured in IGMP Snooping Mrouter Table are described below: Parameter Description Enter the VLAN ID used here. The range is from 1 to 4094.
Page 173: Mld Snooping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description when Port is selected in the Find Type drop-down list. From Port ~ To Port Select the appropriate port range used for the configuration here. This is available when Port is selected in the Find Type drop-down list.
Page 174 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-74 MLD Snooping Settings Window The fields that can be configured in Global Settings are described below: Parameter Description Global State Select this option to enable or disable MLD snooping global state.
Page 175 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-75 MLD Snooping Settings (Show Detail) Window The window displays the detail information about MLD snooping VLAN. Click the Modify button to edit the information in the following window.
Page 176 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Minimum Version Select the minimum version of MLD hosts that is allowed on the VLAN. Options to choose from are 1 and 2. Fast Leave Select this option to enable or disable the MLD snooping fast leave function.
Page 177 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-77 MLD Snooping Groups Settings Window The fields that can be configured in MLD Snooping Static Groups Settings are described below: Parameter Description Enter the VLAN ID of the multicast group here. The range is from 1 to 4094.
Page 178 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Filter Settings, as shown below: Figure 5-78 MLD Snooping Filter Settings Window...
Page 179 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description From Port ~ To Port Select the appropriate port range used for the configuration here. Limit Number Enter the limit number here. This is used to set the limitation on the number of MLD cache entries that can be created.
Page 180 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-79 MLD Snooping Filter Settings Window Click the Back button to return to the previous window. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 181 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in MLD Snooping Mrouter Table are described below: Parameter Description Enter a VLAN ID between 1 and 4094. Click the Find button to locate a specific entry based on the information entered.
Page 182: Multicast Vlan
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description From Port ~ To Port Select the appropriate port range used for the configuration here. This is available when Port is selected in the Find Type drop-down list.
Page 183 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description multicast VLAN, but does not match the associated profile, then the packet will be forwarded or dropped based on this setting. By default, the packet will be dropped.
Page 184 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description the multicast VLAN. Priority Select the priority value here. The range is from 0 to 7. A lower value represents a higher priority. Click the Apply button to accept the changes made.
Page 185 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-83 Multicast VLAN Group Settings Window The fields that can be configured in Group Profile Settings are described below: Parameter Description Profile Name Enter the group profile name for the multicast VLAN feature here. This name can be up to 32 characters long.
Page 186: Pim Snooping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured in Group Profile Table are described below: Parameter Description Profile Enter the group profile name for the multicast VLAN feature here. This name can be up to 32 Name characters long.
Page 187 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured in VLAN Status Settings are described below: Parameter Description Enter the VLAN ID on which the PIM snooping feature will be used here. The range is from 1 to 4094.
Page 188: Multicast Filtering
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-86 PIM Snooping Mroute Table Window The fields that can be configured are described below: Parameter Description Select and enter the VLAN ID that will be used in this display here. The range is from 1 to 4094.
Page 189: Lldp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-88 Multicast Filtering Window The fields that can be configured are described below: Parameter Description Enter the VLAN ID list that will be used for this configuration here.
Page 190 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-89 LLDP Global Settings Window The fields that can be configured in LLDP Global Settings are described below: Parameter Description LLDP State Select this option to enable or disable the LLDP feature LLDP Forward State Select this option to enable or disable LLDP forward state.
Page 191: Lldp Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Message TX Interval Enter the interval between consecutive transmissions of LLDP advertisements on each physical interface. The range is from 5 to 32768 seconds. Message TX Hold Multiplier Enter the multiplier on the LLDPDUs transmission interval that used to compute the TTL value of an LLDPDU.
Page 192: Lldp Management Address List
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description IP Subtype Select the type of the IP address information to be sent. Options to choose from are Default, IPv4 and IPv6. Action Select this option to enable or disable the action field Address Enter the IP address that will be sent.
Page 193: Lldp Dot1 Tlvs Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-92 LLDP Basic TLVs Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 194: Lldp Dot3 Tlvs Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port ~ To Port Select the appropriate port range used for the configuration here.
Page 195: Lldp-Med Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Maximum Frame Size Select this option to enable or disable the Maximum Frame Size TLV to send. The Maximum Frame Size TLV indicates the maximum frame size capability of the implemented MAC and PHY.
Page 196: Lldp Statistics Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-96 LLDP-DCBX Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch’s unit ID that will be used here.
Page 197: Lldp Local Port Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 5-97 LLDP Statistics Information Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used here.
Page 198 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Port Select the port number that will be displayed. Click the Find button to locate a specific entry based on the information entered. Click the Show Detail button to view detailed information of the specific port.
Page 199: Lldp Neighbor Port Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Back button to return to the previous window. LLDP Neighbor Port Information This window is used to display the information learned from the neighbors. The Switch receives packets from a remote station but is able to store the information as local.
Page 200: Layer 3 Features
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Layer 3 Features Gratuitous ARP IPv6 Neighbor Interface UDP Helper IPv4 Static/Default Route IPv4 Static Route BFD IPv4 Route Table IPv6 Static/Default Route IPv6 Route Table Route Preference...
Page 201: Proxy Arp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-2 Static ARP Window The fields that can be configured are described below: Parameter Description IP Address Enter the IP address that will be associated with the MAC address here.
Page 202: Arp Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide ARP Table This window is used to display and configure the ARP table settings. To view the following window, click L3 Features > ARP > ARP Table, as shown below:...
Page 203: Ipv6 Neighbor
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-5 Gratuitous ARP Window The fields that can be configured are described below: Parameter Description Select to enable or disable the learning of gratuitous ARP packets in the ARP IP Gratuitous ARP State cache table.
Page 204: Interface
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-6 IPv6 Neighbor Window The fields that can be configured are described below: Parameter Description Interface VLAN Enter the VLAN interface’s ID here. IPv6 Address Enter the IPv6 address.
Page 205 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Edit button to re-configure the specific entry. Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 206: Ipv6 Interface
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 207 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Interface VLAN Enter the VLAN interface’s ID that will be associated with the IPv6 entry. Click the Apply button to accept the changes made. Click the Find button to locate a specific entry based on the information entered.
Page 208 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description IPv6 Address Enter the IPv6 address for this IPv6 interface here. Select the EUI-64 option to configure an IPv6 address on the interface using the EUI-64 interface ID. Select the Link Local option to configure a link-local address for the IPv6 interface.
Page 209: Loopback Interface
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-13 IPv6 Interface (Detail, Neighbor Discover) Window After selecting the DHCPv6 Client tab option, at the top of the page, the following page will be available.
Page 210 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-15 Loopback Interface Window The fields that can be configured are described below: Parameter Description Interface Loopback Enter the loopback interface’s ID here. The range is from 1 to 8.
Page 211: Null Interface
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to delete the specified entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 212: Ip Helper Address
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Forward Protocol UDP Enter the destination port of the UDP service to be forwarded here. The range is Port from 1 to 65535.
Page 213: Ipv4 Static Route Bfd
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide by the user. Once an ARP response has been retrieved by the Switch from that next hop, the route becomes enabled. However, if the ARP entry already exists, an ARP request will not be sent.
Page 214: Ipv4 Route Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-21 IPv4 Static Route BFD Window The fields that can be configured are described below: Parameter Description Enter the name of the interface that will be used to create the BFD session here.
Page 215: Ipv6 Static/Default Route
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 216: Ipv6 Route Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-24 IPv6 Static Route BFD Window The fields that can be configured are described below: Parameter Description Interface Name Enter the name of the interface that will be associated with this route here.
Page 217: Route Preference
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Database Select this option to display all the related entries in the routing database instead of just the best route. Hardware Select this option to display only hardware routes. Hardware routes are routes that have been written into the hardware chip.
Page 218: Rip
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-27 IPv6 General Prefix Window The fields that can be configured are described below: Parameter Description Interface VLAN Enter the VLAN interface ID used here. The range is from 1 to 4094.
Page 219 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-28 RIP Settings Window The fields that can be configured in RIP Global Settings are described below: Parameter Description RIP State Select to globally enable or disable the Routing Information Protocol (RIP) feature here.
Page 220: Rip Distribute List
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description seconds. Select the Default option to use the default value here which is 180 seconds. Flush Time Enter the flush timer value in seconds here. The range is from 1 to 65535 seconds.
Page 221: Rip Database
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-30 RIP Interface Settings Window The fields that can be configured are described below: Parameter Description Network Enter the IPv4 network address used by RIP here. The interface that has a subnet defined belonging to a network specified here will be activated with RIP.
Page 222: Ripng
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Network Address Enter the subnet prefix and the prefix length of the network(s) to be displayed here. Click the Find button to locate a specific entry based on the information entered.
Page 223: Ripng Interface Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description distance value represents the trust rating of the route. The route with a lower distance value is preferred over the route with the higher distance value. Select the Default option to use the default administrative distance for RIPng, which is 120.
Page 224: Ripng Database
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Interface VLAN Enter the VLAN interface’s ID here. The range is from 1 to 4094. Tick the All Interface check box to configure all interfaces.
Page 225 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-35 IP Multicast Global Settings Window The fields that can be configured are described below: Parameter Description Table Lookup Mode Select the IP multicast table lookup mode here. Options to choose from are IP and MAC.
Page 226: Ipv6Mc
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-37 Control Packet CPU Filtering Window The fields that can be configured in Control Packet CPU Filtering Settings are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 227: Bfd
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click L3 Features > IP Multicast Routing Protocol > IPv6MC > IPv6 Multicast Routing Forwarding Cache Table, as shown below: Figure 6-38 IPv6 Multicast Routing Forwarding Cache Table Window...
Page 228: Bfd Neighbor Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Find button to find and display an entry based on the information entered. Click the Edit button to configure the interval settings for the specific entry.
Page 229: Ip Route Filter
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IP Route Filter Route Map This window is used to display and configure the route map’s settings. To view the following window, click L3 Features > IP Route Filter > Route Map, as shown below:...
Page 230 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-43 Route Map (Match Clauses, Edit) Window The fields that can be configured are described below: Parameter Description Action Select Add to add a new entry based in the information entered.
Page 231 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-44 Route Map (Set Clauses, Edit) Window The fields that can be configured are described below: Parameter Description Action Select Add to add a new entry based in the information entered.
Page 232: Policy Route
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Policy Route This window is used to display and configure the policy route settings. To view the following window, click L3 Features > Policy Route, as shown below: Figure 6-45 Policy Route Window Click the Edit button to modify the specified entry.
Page 233 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-47 VRRP Settings Window The fields that can be configured in VRRP Settings are described below: Parameter Description SNMP Server Traps VRRP Select to enable or disable the SNMP server traps feature for the new VRRP New Master master.
Page 234: Vrrpv3 Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Edit button, the following page will appear.
Page 235 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 6-49 VRRPv3 Settings Window The fields that can be configured are described below: Parameter Description VLAN Enter the ID of the VLAN interface that will be used here. The range is from 1 to 4094.
Page 236 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Virtual IP Address Enter the virtual IPv4/IPv6 address here. This parameter will be either IPv4 or IPv6 depending on the Address Family selection made in the previous step. All routers in the same VRRP group must be configured with the same virtual router ID and virtual address.
Page 237: Quality Of Service (Qos)
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Quality of Service (QoS) Basic Settings Advanced Settings QoS PFC WRED iSCSI Basic Settings Port Default CoS This window is used to display and configure the port’s default CoS settings.
Page 238 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-2 Port Scheduler Method Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 239: Queue Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description environment. Using bandwidth allocations, different traffic classes within different traffic types such as LAN, SAN, IPC and management can be configured to provide bandwidth allocation, low-latency or best effort transmit characteristics.
Page 240: Port Rate Limiting
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click QoS > Basic Settings > CoS to Queue Mapping, as shown below: Figure 7-4 CoS to Queue Mapping Window The fields that can be configured are described below:...
Page 241: Queue Rate Limiting
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • When Bandwidth is selected, enter the input/output bandwidth value used in the space provided. This value must be between 8 and 10000000 kbps. Also, enter the Burst Size value in the space provided.
Page 242: Advanced Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description packets transmitted from the queue cannot exceed the maximum bandwidth even if the bandwidth is available. When configuring the minimal bandwidth, the aggregate of the configured minimum bandwidth must be less than 75 percent of the interface bandwidth to make sure the configured minimal bandwidth can be guaranteed.
Page 243: Port Trust State And Mutation Binding
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Output DSCP List Enter the output DSCP list value here. This value must be between 0 and 63. Click the Apply button to accept the changes made.
Page 244: Cos Color Mapping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-9 DSCP CoS Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 245: Dscp Color Mapping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-10 CoS Color Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 246: Class Map
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-11 DSCP Color Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 247: Aggregate Policer
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Match button to configure the specific entry. Click the Delete button to remove the specific entry.
Page 248 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click QoS > Advanced Settings > Aggregate Policer, as shown below: Figure 7-14 Aggregate Policer (Single Rate Setting) Window The fields that can be configured are described below:...
Page 249 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • When selecting the Set-DSCP-1P option, enter the IP DSCP and 1P transmit values in the spaces provided. Select the violate action here. The violate action specifies the action to take on Violate Action packets that violate the normal and maximum burst sizes for singe rate policing.
Page 250 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description bucket for the two-rate metering. Confirm Burst Enter the confirm burst value here. This value must be between 0 and 16384 Kbytes. The confirm burst value specifies the burst size for the first token bucket in kbps.
Page 251: Policy Map
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • When selecting the Transmit option, packets will be transmitted unaltered. • When selecting the Set-DSCP-1P option, enter the IP DSCP and 1P transmit values in the spaces provided.
Page 252 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Set Action button to configure the set action settings for the specified entry. Click the Policer button to configure the policer settings for the specified entry.
Page 253 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-18 Policy Map (Policer) Window The fields that can be configured are described below: Parameter Description None Select this option to specify that no policer settings will be configured for this entry.
Page 254: Policy Binding
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Transmit - Specifies that the exceed action is to transmit the packet unmodified. • Set-DSCP-1P - Specifies that the exceed action is to modify the DSCP and 802.1p values and then to transmit the packet with the new DSCP and...
Page 255: Qos Pfc
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port ~ To Port Select the range of ports that will be used for this configuration here.
Page 256: Network Qos Policy Map
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Match Select the IEEE 802.1Q Class of Service (CoS) value to be matched here. The range is from 0 to 7. When a packet is received, the packet will be given an internal CoS. This internal CoS is used to select the transmit queue based on the CoS to queue map.
Page 257: Network Qos Policy Binding
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After clicking the Edit button, the following page will appear. Figure 7-23 Network QoS Policy Map (Edit) Window The fields that can be configured are described below:...
Page 258: Pfc Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch’s unit ID that will be used here. From Port ~ To Port Select the Switch’s port range that will be used here.
Page 259: Wred
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • RX - Specifies to clear the counters of received PFC frames. • TX - Specifies to clear the counters of transmitted PFC frames. • Both - Specifies to clear the counters of received and transmitted PFC frames.
Page 260: Wred Queue
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Red - Specifies the WRED drop parameters for red packets to be set. Min Threshold Enter the minimum threshold value here that will be used to start WRED dropping.
Page 261: Wred Drop Counter
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description WRED State Select to enable or disable the WRED feature state on the specified port(s) here. Profile Enter the WRED profile’s ID here. The range is from 1 to 128.
Page 262 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-29 ETS Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch’s unit ID that will be used here.
Page 263: Ets Recommend Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide ETS Recommend Settings This window is used to display and configure the ETS recommended settings on the specified interface. These settings will be translated to a DCBX ETS recommendation TLV. The TLV is encoded into each LLDP message and may be transmitted by a system in order to indicate a recommendation on how ETS should be configured.
Page 264: Qcn
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide QCN CNPV Status This window is used to display and configure the Quantized Congestion Notification (QCN) Congestion Notification Priority Value (CNPV) status on the Switch. QCN is a form of end-to-end congestion management defined in IEEE 802.1.Qau. The purpose of QCN is to ensure that congestion is controlled from the sending device to the receiving device in a dynamic fashion that can deal with changing bottlenecks.
Page 265 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-33 QCN CNPV Settings Window The fields that can be configured are described below: Parameter Description Select the IEEE 802.1p priority value to be the Congestion Notification Priority Value (CNPV) here.
Page 266: Qcn Cnpv Interface Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Disable - Specifies that the congestion notification capability is administratively disabled for this priority. • Interior - Specifies that the priority parameter of the frame input is not remapped to or from this priority and the frames are transmitted without a CN-TAG.
Page 267: Qcn Cnpv Interface Simple
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description are specified by administrator. • Auto - Specifies that the default CND defense mode and alternate priority are controlled automatically. • Comp - Specifies that the default CND defense mode and alternate priority are determined by global setting.
Page 268: Qcn Cp Interface Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide QCN CP Interface Settings This window is used to display and configure the QCN Congestion Point (CP) interface settings. To view the following window, click QoS > QCN > QCN CP Interface Settings, as shown below:...
Page 269: Qcn Cp Counters
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description value. The range is from -10 to 10. By default, this value is 2. Click the Apply button to accept the changes made. QCN CP Counters This window is used to display and clear the QCN CP counters.
Page 270: Iscsi
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 7-39 QCN CPID Table Window The fields that can be configured are described below: Parameter Description QCN CPID Enter the Congestion Point Identifier (CPID) to get the corresponding interface ID and CP index.
Page 271: Iscsi Sessions
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description DSCP when egressing the Switch. Session Aging Time Enter the session aging time value here. The range is from 1 to 43200 minutes. This is used to configure the aging time for iSCSI sessions. When configuring the aging time to be longer than the current setting, the current sessions will be timed out and use the new aging time.
Page 272: Access Control List (Acl)
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Access Control List (ACL) ACL Configuration Wizard ACL Access List ACL Interface Access Group ACL VLAN Access Map ACL VLAN Filter CPU ACL ACL Configuration Wizard This window is used to guide the user to create a new ACL access list or configure an existing ACL access list.
Page 273: Step 2 - Select Packet Type
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Create Select this option to create a new ACL access list using the configuration wizard. ACL Name Enter the new ACL’s name here. This name can be up to 32 characters long.
Page 274 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 8-4 ACL Configuration Wizard (Create, Packet Type, MAC) Window The fields that can be configured are described below: Parameter Description Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535.
Page 275 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Ethernet Type Enter the Ethernet type hexadecimal value here. This value must be between 0x600 and 0xFFFF. When any Ethernet type profile is selected in the Specify Ethernet Type drop-down list, the appropriate hexadecimal value will automatically be entered.
Page 276 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IPv4 After clicking the IPv4 radio button and the Next button, the following window will appear. Figure 8-5 ACL Configuration Wizard (Create, Packet Type, IPv4) Window The fields that can be configured are described below:...
Page 277 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Host, and IP. • When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. • When the Host option is selected, enter the source host’s IP address here.
Page 278 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description provided. The range is from 0x0 to 0xFFFF. This parameter is only available in the protocol type TCP and UDP. Specify ICMP Message Select the ICMP message type used here.
Page 279 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IPv6 After clicking the IPv6 radio button and the Next button, the following window will appear. Figure 8-6 ACL Configuration Wizard (Create, Packet Type, IPv6) Window The fields that can be configured are described below:...
Page 280 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Host, and IPv6. • When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. • When the Host option is selected, enter the source host’s IPv6 address here.
Page 281: Step 4 - Apply Port
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Specify ICMP Message Select the ICMP message type used here. Type This parameter is only available in the protocol type ICMP. ICMP Message Type When the ICMP Message Type is not selected, enter the ICMP Message Type numerical value used here.
Page 282: Acl Access List
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port ~ To Port Select the appropriate port range used for the configuration here.
Page 283 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Delete button, next to the ACL rule, to remove the specific ACL rule. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 284: Standard Ip Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Standard IP ACL, Extended IP ACL, Standard IPv6 ACL, Extended IPv6 ACL, Extended MAC ACL, and Extended Expert ACL. Enter the ID for the ACL here.
Page 285: Extended Ip Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description bit value 0 will be checked. Destination Select and enter the destination information here. Options to choose from are Any, Host, IP, and Wildcard. • When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 286 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description this value is not specified, the system will automatically generate an ACL rule number for this entry. Action Select the action that this rule will take here. Options to choose from are Permit and Deny.
Page 287 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • When selecting the = option, the specific selected port number will be used. • When selecting the > option, all ports greater than the selected port, will be used.
Page 288: Standard Ipv6 Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Back button to discard the changes made and return to the previous page. Standard IPv6 ACL After selecting a Standard IPv6 ACL and clicking the Add Rule button, the following page will appear.
Page 289: Extended Ipv6 Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Back button to discard the changes made and return to the previous page. Extended IPv6 ACL After selecting an Extended IPv6 ACL and clicking the Add Rule button, the following page will appear.
Page 290 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • When the Host option is selected, enter the source host’s IPv6 address here. • When the IPv6 option is selected, the Prefix Length option will also be available.
Page 291: Extended Mac Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Specify ICMP Message Select the ICMP message type used here. Type This parameter is only available in the protocol type ICMP. ICMP Message Type When the ICMP Message Type is not selected, enter the ICMP Message Type numerical value used here.
Page 292 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 8-15 Extended MAC ACL (Add Rule) Window The fields that can be configured are described below: Parameter Description Sequence No. Enter the sequence number of this ACL rule here. The range is from 1 to 65535. If this value is not specified, the system will automatically generate an ACL rule number for this entry.
Page 293: Extended Expert Acl
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description 0x600 and 0xFFFF. When the Ethernet type profile is selected, above, the appropriate hexadecimal value will automatically be entered. Ethernet Type Mask Enter the Ethernet type mask hexadecimal value here. This value must be between 0x0 and 0xFFFF.
Page 294 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 8-16 Extended Expert ACL (Add Rule) Window The fields that can be configured are described below: Parameter Description Sequence No. Enter the sequence number of this ACL rule here. The range is from 1 to 65535. If this value is not specified, the system will automatically generate an ACL rule number for this entry.
Page 295 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Destination Select and enter the destination IP information here. Options to choose from are Any, Host, and IP.
Page 296 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description used. • When selecting the < option, all ports smaller than the selected port, will be used. • When selecting the ≠ option, all ports, excluding the selected port, will be used.
Page 297: Acl Interface Access Group
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description is from 1 to 4094. • Mask - Enter the inner VLAN ID mask value here. The range is from 0x0 to 0xFFF. VLAN Range Select and enter the VLAN range that will be associated with this ACL rule here.
Page 298: Acl Vlan Access Map
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. After clicking the Please Select button, the following window will appear: Figure 8-18 ACL Interface Access Group (Please Select) Window Select the radio button next to the entry to use that ACL in the configuration.
Page 299 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Clear Counter button to the clear the counter information for the specified access map. Click the Find button to locate a specific entry based on the information entered.
Page 300: Acl Vlan Filter
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide ACL VLAN Filter This window is used to display and configure the ACL VLAN filter settings. To view the following window, click ACL > ACL VLAN Filter, as shown below:...
Page 301 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Binding button to configure the binding settings for the specified entry.
Page 302 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in Match MAC Access List are described below: Parameter Description Sequence No. Enter the sequence number of the associated match entry here. The range is from 1 to 65535.
Page 303: Security
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Security Port Security 802.1X RADIUS TACACS+ IMPB DHCP Server Screening ARP Spoofing Prevention BPDU Attack Protection NetBIOS Filtering MAC Authentication Web-based Access Control Network Access Authentication Safeguard Engine...
Page 304: Port Security Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Trap State Click to enable or disable port security traps on the Switch. Click the Apply button to accept the changes made. The fields that can be configured in Port Security Trap Rate Settings are described below:...
Page 305 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-2 Port Security Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 306: Port Security Address Entries
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description specified time period. Click the Apply button to accept the changes made. Port Security Address Entries This window is used to display, clear and configure the port security address entries.
Page 307 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-4 The EAPOL Packet Utilizing this method, unauthorized devices are restricted from connecting to a LAN through a port to which the user is connected. EAPOL packets are the only traffic that can be transmitted through the specific port until authorization is granted.
Page 308 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-6 The Authentication Server Authenticator The Authenticator (the Switch) is an intermediary between the Authentication Server and the Client. The Authenticator serves two purposes when utilizing the 802.1X function. The first purpose is to request certification information from the Client through EAPOL packets, which is the only information allowed to pass through the Authenticator before access is granted to the Client.
Page 309 Figure 9-9 The 802.1X Authentication Process The D-Link implementation of 802.1X allows network administrators to choose between two types of Access Control used on the Switch, which are: • Port-based Access Control - This method requires only one user to be authenticated per port by a remote RADIUS server to allow the remaining users on the same port access to the network.
Page 310 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The original intent behind the development of 802.1X was to leverage the characteristics of point-to-point in LANs. As any single LAN segment in such infrastructures has no more than two devices attached to it, one of which is a Bridge Port.
Page 311: 802.1X Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-11 Example of Typical Host-based Configuration 802.1X Global Settings This window is used to display and configure the 802.1X global settings. To view the following window, click Security > 802.1X > 802.1X Global Settings, as shown below: Figure 9-12 802.1X Global Settings Window...
Page 312: Authentication Sessions Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-13 802.1X Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 313: Authenticator Statistics
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-14 Authentication Sessions Information Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 314: Authenticator Session Statistics
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Authenticator Session Statistics This window is used to display and clear the authenticator session statistics. To view the following window, click Security > 802.1X > Authenticator Session Statistics, as shown below:...
Page 315: Aaa
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-17 Authenticator Diagnostics Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this query here.
Page 316: Application Authentication Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description AAA State Select to enable or disable the Authentication, Authorization, and Accounting (AAA) global state. Click the Apply button to accept the changes made. Application Authentication Settings This window is used to display and configure the application authentication settings.
Page 317 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-21 Application Accounting Settings Window Click the Edit button to re-configure the specific entry. Figure 9-22 Application Accounting Settings (Edit) Window The fields that can be configured in Application Accounting Exec Method list are described below:...
Page 318: Authentication Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. Authentication Settings This window is used to display and configure the AAA network and EXEC authentication settings.
Page 319 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • local - Specifies to use the local database for authentication. • group - Specifies to use the server groups defined by the AAA group server.
Page 320: Accounting Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in AAA Authentication Enable are described below: Parameter Description Status Select to enable or disable the AAA authentication enable state here.
Page 321 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-25 Accounting Settings Window The fields that can be configured in AAA Accounting Network are described below: Parameter Description Default Select to enable or disable the use of the default method list here.
Page 322: Radius
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description List Name Enter the method list name that will be used with the AAA accounting EXEC option here. Method 1 ~ Method 4 Select the method lists that will be used for this configuration here. Options to choose from are none, group, radius, and tacacs+.
Page 323: Radius Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-29 RADIUS Global Settings Window The fields that can be configured in RADIUS Global Settings are described below: Parameter Description DeadTime Enter the dead time value here. This value must be between 1 and 1440 minutes.
Page 324: Radius Group Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-30 RADIUS Server Settings Window The fields that can be configured are described below: Parameter Description IP Address Enter the RADIUS server’s IPv4 address here. IPv6 Address Enter the RADIUS server’s IPv6 address here.
Page 325: Radius Statistic
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Group Server Name Enter the RADIUS group server’s name here. This name can be up to 32 characters long. IP Address Enter the group server’s IPv4 address here.
Page 326: Tacacs
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-33 RADIUS Statistic Window The fields that can be configured are described below: Parameter Description Group Server Name Select the RADIUS group server name from this list here.
Page 327: Tacacs+ Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description IPv4 TACACS+ Source Enter the name of the IPv4 TACACS+ source interface here. Interface Name Click the Apply button to accept the changes made. The fields that can be configured in TACACS+ Global IPv6 Source Interface are described below:...
Page 328 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Security > TACACS+ > TACACS+ Group Server Settings, as shown below: Figure 9-36 TACACS+ Group Server Settings Window The fields that can be configured are described below:...
Page 329: Tacacs+ Statistic
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide TACACS+ Statistic This window is used to display and clear the TACACS+ statistic information. To view the following window, click Security > TACACS+ > TACACS+ Statistic, as shown below:...
Page 330 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description DHCP Snooping Select to enable or disable the DHCP snooping global status. Information Option Allow Select to enable or disable the option to globally allow DHCP packets with the Untrusted relay Option 82 on the untrusted interface.
Page 331 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description untrusted interfaces. DHCP snooping acts as a firewall between untrusted interfaces and DHCP servers. Click the Apply button to accept the changes made. DHCP Snooping VLAN Settings This window is used to display and configure the DHCP snooping VLAN settings.
Page 332 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-42 DHCP Snooping Database Window The fields that can be configured in DHCP Snooping Database are described below: Parameter Description Write Delay Enter the write delay time value here. This value must be between 60 and 86400 seconds.
Page 333: Dynamic Arp Inspection
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Security > IMPB > IPv4 > DHCPv4 Snooping > DHCP Snooping Binding Entry, as shown below: Figure 9-43 DHCP Snooping Binding Entry Window...
Page 334 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description ARP Access List Name Enter the ARP access list name used here. This name can be up to 32 characters long.
Page 335 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-46 ARP Inspection Settings Window The fields that can be configured in ARP Inspection Validation are described below: Parameter Description Src-MAC Select to enable or disable the source MAC option here. This option specifies to...
Page 336 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide ARP Inspection Port Settings This window is used to display and configure the ARP inspection port settings. To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP Inspection Port...
Page 337 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description VID List Enter the VLAN ID list used here. State Select to enable or disable the ARP inspection option’s state for the specified VLAN here.
Page 338: Ip Source Guard
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Clear Log button to clear the log. IP Source Guard IP Source Guard Port Settings This window is used to display and configure the IP source guard port settings.
Page 339 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-52 IP Source Guard Binding Window The fields that can be configured in IP Source Binding Settings are described below: Parameter Description MAC Address Enter the MAC address of the binding entry here.
Page 340 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IP Source Guard HW Entry This window is used to display the IP source guard hardware entries. To view the following window, click Security > IMPB > IPv4 > IP Source Guard > IP Source Guard HW Entry, as...
Page 341 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Trap State Select the enable or disable the IP-MAC-Port binding option’s trap state. Click the Apply button to accept the changes made. The fields that can be configured in IP-MAC-Port Binding Port Settings are described below:...
Page 342: Ipv6
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IPv6 IPv6 Snooping This window is used to display and configure the IPv6 snooping settings. To view the following window, click Security > IMPB > IPv6 > IPv6 Snooping, as shown below:...
Page 343 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IPv6 ND Inspection This window is used to display and configure the IPv6 ND inspection settings. To view the following window, click Security > IMPB > IPv6 > IPv6 ND Inspection, as shown below:...
Page 344 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-58 IPv6 RA Guard Window The fields that can be configured are described below: Parameter Description Enter the policy name here. This name can be up to 32 characters long.
Page 345 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-60 IPv6 DHCP Guard Window The fields that can be configured are described below: Parameter Description Policy Name Enter the policy name here. This name can be up to 32 characters long.
Page 346: Ipv6 Source Guard
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide IPv6 Source Guard IPv6 Source Guard Settings This window is used to display and configure the IPv6 source guard settings. To view the following window, click Security > IMPB > IPv6 > IPv6 Source Guard > IPv6 Source Guard Settings,...
Page 347: Dhcp Server Screening
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-63 IPv6 Neighbor Binding Window The fields that can be configured in IPv6 Neighbor Binding Settings are described below: Parameter Description MAC Address Enter the MAC address used here.
Page 348: Dhcp Server Screening Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide When the DHCP Server Screening function is enabled on a port, all DHCP server packets received on this ports will be redirected to the CPU for a software-based check. Legal DHCP server packets will be forwarded out and illegal DHCP server packets will be dropped.
Page 349: Dhcp Server Screening Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Clear Log button to clear the log. DHCP Server Screening Port Settings This window is used to display and configure the DHCP server screening port settings.
Page 350: Bpdu Attack Protection
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-66 ARP Spoofing Prevention Window The fields that can be configured are described below: Parameter Description Select the Switch unit that will be used for this configuration here.
Page 351: Netbios Filtering
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-67 BPDU Attack Protection Window The fields that can be configured in BPDU Attack Protection Global Settings are described below: Parameter Description BPDU Attack Protection Select to enable or disable the BPDU attack protection feature’s global state here.
Page 352: Mac Authentication
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-68 NetBIOS Filtering Window The fields that can be configured are described below: Parameter Description Select the Switch unit that will be used for this configuration here.
Page 353 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-69 MAC Authentication Window The fields that can be configured in MAC Authentication Global Settings are described below: Parameter Description MAC Authentication State Select to enable or disable the MAC authentication feature’s global state.
Page 354: Web-Based Access Control
WAC by attempting to gain Web access. D-Link’s implementation of WAC uses a virtual IP that is exclusively used by the WAC function and is not known by any other modules of the Switch. In fact, to avoid affecting a Switch’s other features, WAC will only use a virtual IP address to communicate with hosts.
Page 355 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-70 RADIUS Authentication Server Conditions and Limitations • If the client is utilizing DHCP to attain an IP address, the authenticating VLAN must provide a DHCP server or a DHCP relay function so that client may obtain an IP address.
Page 356: Web Authentication
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Web Authentication This window is used to display and configure the Web authentication settings. To view the following window, click Security > Web-based Access Control > Web Authentication, as shown below:...
Page 357: Wac Customize Page
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-72 WAC Port Settings Window The fields that can be configured are described below: Parameter Description Select the Switch unit that will be used for this configuration here.
Page 358: Network Access Authentication
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Page Title Enter a custom page title message here. This message can be up to 128 characters long.
Page 359 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Security > Network Access Authentication > Network Access Authentication Global Settings, as shown below: Figure 9-75 Network Access Authentication Global Settings Window...
Page 360: Network Access Authentication Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Authorization State Select to enable or disable the authorized state here. The option is used to enable or disable the acceptance of an authorized configuration. When authorization is enabled for authentication, the authorized attributes (for example VLAN, 802.1p...
Page 361: Network Access Authentication Sessions Information
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description From Port ~ To Port Select the appropriate port range used for the configuration here. Host Mode Select the host mode option that will be associated with the selected port(s) here.
Page 362: Safeguard Engine
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-77 Network Access Authentication Sessions Information Window The fields that can be configured are described below: Parameter Description Port Select the appropriate Switch unit and port used for the query here.
Page 363: Safeguard Engine Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Protocol Name Sub-interface Description (Group) 802.1X Protocol Port-based Network Access Control Protocol Address resolution Protocol (ARP) DHCP Protocol Dynamic Host Configuration Protocol Protocol Domain Name System GVRP...
Page 364: Cpu Protect Counters
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in Safeguard Engine Settings are described below: Parameter Description Safeguard Engine State Select to enable or disable the safeguard engine feature here.
Page 365: Cpu Protect Type
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-80 CPU Protect Sub-Interface Window The fields that can be configured in CPU Protect Sub-Interface are described below: Parameter Description Sub-Interface Select the sub-interface option here. Options to choose from are Manage, Protocol, and Route.
Page 366: Trusted Host
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured in Protect Type Information are described below: Parameter Description Protocol Name Select the protocol name option here.
Page 367: Storm Control
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-83 Traffic Segmentation Settings Window The fields that can be configured are described below: Parameter Description Unit Select the receiving Switch unit that will be used for this configuration here.
Page 368 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Trap State Select the storm control trap option here. Options to choose from are None, Storm Occur, Storm Clear, and Both. When None is selected, no traps will be sent.
Page 369: Dos Attack Prevention Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The additional fields that can be configured in Storm Control Port Settings are described below: Parameter Description KBPS Rise Enter the rise KBPS value used here. This option specifies the rise threshold value as a rate of kilobits per second at which traffic is received on the port.
Page 370: Ssh
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide ping packet is illegal according to networking protocol, but a packet of such a size can be sent if it is fragmented; when the target computer reassembles the packet, a buffer overflow can occur, which often causes a system crash.
Page 371: Ssh Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide will provide secure encrypted and authenticated communication between two non-trusted hosts. SSH, with its array of unmatched security features is an essential tool in today’s networking environment. It is a powerful guardian against numerous existing security hazards that now threaten network communications.
Page 372: Ssh Server Connection
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-89 Host Key Window The fields that can be configured in Host Key Management are described below: Parameter Description Select the crypto key type used here. Options to choose from are the Rivest...
Page 373: Ssh User Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Security > SSH > SSH Server Connection, as shown below: Figure 9-92 SSH Server Connection Window SSH User Settings This window is used to display and configure the SSH user settings.
Page 374: Ssl Global Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide • Key Exchange: The first part of the Cipher suite string specifies the public key algorithm to be used. This switch utilizes the Rivest Shamir Adleman (RSA) public key algorithm and the Digital Signature Algorithm (DSA), specified here as the DHE DSS Diffie-Hellman (DHE) public key algorithm.
Page 375: Crypto Pki Trustpoint
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured in SSL Global Settings are described below: Parameter Description SSL Status Select to enable or disable the SSL feature’s global status here.
Page 376: Ssl Service Policy
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Selecting Local specifies to import local certificate and key pairs only. Click the Apply button to accept the changes made. Click the Find button to locate a specific entry based on the information entered.
Page 377: Sftp Server Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description long. Cipher Suites Select the cipher suites that should be used by the secure service when negotiating a connection with a remote peer. When no cipher suite is selected, the SSL client and server will negotiate the best cipher suite that they both support from the available cipher suites.
Page 378 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 9-97 SFTP Server Settings Window The fields that can be configured are described below: Parameter Description SFTP Server Select to globally enable or disable the SFTP server feature here.
Page 379: 10. Oam
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide 10. OAM Cable Diagnostics Ethernet OAM CFM Settings This window is used to display and configure the Connectivity Fault Management (CFM) feature’s settings. To view the following window, click OAM > CFM > CFM Settings, as shown below:...
Page 380 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description easy identification of administrative responsibility for each maintenance domain. Domain Level Enter the Maintenance Domain’s (MD’s) level here. The range is from 0 to 7. A unique MD level is assigned to define the hierarchical relationship between domains.
Page 381 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Chassis - Specifies to transmit the sender ID TLV with the chassis ID information. • Manage - Specifies to transmit the sender ID TLV with the managed address information.
Page 382 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description MA Mode Select the MA mode here. Options to choose from are: • Software - Specifies that the MA works in the CFM software mode.
Page 383 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After clicking the Add MEP button, the following page will appear. Figure 10-5 CFM Settings (Add MA, Add MEP) Window The fields that can be configured are described below:...
Page 384 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-6 CFM Settings (Add MA, Add MEP, MEPID Detail) Window Click the Edit button to modify the specified entry. Click the Back button to return to the previous window.
Page 385 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-7 CFM Settings (Add MA, Add MEP, MEPID Detail, Edit) Window The fields that can be configured are described below: Parameter Description MEP State Select to enable or disable the MEP’s state on the interface here.
Page 386 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description sent. Alarm Time Enter the time period to control the period time from when a defect is detected on the MEP to a fault alarm that will be sent. The range is from 250 to 1000 centiseconds.
Page 387 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After clicking the Edit DM button, the following page will appear. Figure 10-10 CFM Settings (Add MA, Add MEP, Edit DM) Window The fields that can be configured in CFM DM Settings are described below:...
Page 388 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description default value is the PDU priority of the MEP. Click the Apply button to accept the changes made. The fields that can be configured in Clear CFM DM are described below:...
Page 389: Cfm Port Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description MAC Address Enter the MAC address for the LM test here. Period Select the time period here. This specifies the transmitting interval of the LM PDU.
Page 390: Cfm Loopback Test
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 10-13 CFM Port Settings (View Detail) Window Click the Back button to return to the previous window.
Page 391: Cfm Linktrace Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description PDU Priority Select the 802.1p priority to be set in the transmitted LBMs here. If not specified, it uses the same priority as the CCMs sent by the MEP. The range is from 0 to 7.
Page 392: Cfm Packet Counter
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Clear All button to clear the information associated with all entries. Click the Show Detail button to view more detailed information about the link-trace entry.
Page 393: Cfm Counter Ccm
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide CFM Counter CCM This window is used to display and clear the CFM CCM counter information. To view the following window, click OAM > CFM > CFM Counter CCM, as shown below: Figure 10-18 CFM Counter CCM Window Click the Clear button to clear the counter information associated with all entries.
Page 394: Ethernet Oam
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-21 Cable Diagnostics Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 395 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-22 Ethernet OAM Settings Window The fields that can be configured in Ethernet OAM Settings are described below: Parameter Description Unit Select the Switch’s unit ID that will be used here.
Page 396: Ethernet Oam Configuration Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Stop - Specifies to request the peer to change to the normal operation mode. If the remote peer is configured to ignore the remote loopback request, then the remote peer will not enter or exit the remote loopback mode upon receiving the request.
Page 397 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-23 Ethernet OAM Configuration Settings Window The fields that can be configured in Ethernet OAM Configuration Settings are described below: Parameter Description Unit Select the Switch’s unit ID that will be used here.
Page 398 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Error Frame Seconds - This feature is used to enable notifying the Ethernet OAM error frame second event and configure the monitor threshold and window on the specified port.
Page 399: Ethernet Oam Event Log Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch’s unit ID that will be used here. From Port ~ To Port Select the Switch’s port range that will be used here.
Page 400: Ethernet Oam Duld Settings
Click the Show All button to display all the statistics information. Ethernet OAM DULD Settings This window is used to display and configure the Ethernet OAM feature’s D-Link Unidirectional Link Detection (DULD) settings. DULD is an extension of 802.3ah Ethernet OAM. It provides a mechanism to detect a unidirectional point-to- point Ethernet link without PHY support.
Page 401: Ddm
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-26 Ethernet OAM DULD Settings Window The fields that can be configured in Ethernet OAM DULD Settings are described below: Parameter Description Recovery Time Enter the time interval value used by DULD to decide how long to recover the disabled port here.
Page 402: Ddm Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings, bias current threshold settings, Tx power threshold settings, and Rx power threshold settings.
Page 403: Ddm Temperature Threshold Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide DDM Temperature Threshold Settings This window is used to display and configure the DDM Temperature Threshold Settings for specific ports on the Switch. To view the following window, click OAM > DDM > DDM Temperature Threshold Settings, as shown below:...
Page 404: Ddm Bias Current Threshold Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete.
Page 405: Ddm Rx Power Threshold Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 10-31 DDM TX Power Threshold Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 406: Ddm Status Table
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete.
Page 407: 11. Monitoring
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide 11. Monitoring VLAN Counter Utilization Statistics Mirror Settings sFlow Device Environment External Alarm Settings VLAN Counter This window is used to display and configure the VLAN counter settings. This is used to create a control entry for traffic statistics on specified Layer 2 VLAN interface(s).
Page 408: Utilization
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • Both - Specifies to count ingress and egress traffic. Click the Apply button to accept the changes made. Click the Delete button to delete the specified entry based on the information entered/selected.
Page 409: History Utilization
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide History Utilization This window is used to display the memory, CPU and port history utilization. To view the following window, click Monitoring > Utilization > History Utilization, as shown below:...
Page 410: Statistics
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description • CPU - Specifies to display the historical CPU utilization information. • Port - Specifies to display the historical port utilization information. Time Based Select the time-based statistical count value here. Options to choose from are: •...
Page 411: Cpu Port
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-7 Port (Show Detail) Window Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table.
Page 412: Interface Counters
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-8 CPU Port Window The fields that can be configured are described below: Parameter Description Type Select the type of information to display here. Options to choose from are All, Layer 2 (L2), Layer 3 (L3), and Protocol.
Page 413 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-9 Interface Counters (Port) Window The fields that can be configured are described below: Parameter Description Select the type of information to display here. Options to choose from are Port Type and VLAN.
Page 414: Interface History Counters
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table. After selecting VLAN as the Type, the following window will appear:...
Page 415 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-12 Interface History Counters (Port) Window The fields that can be configured are described below: Parameter Description Type Select the type of information to display here.
Page 416: Counters
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Counters This window is used to display and clear counter information. To view the following window, click Monitoring > Statistics > Counters, as shown below: Figure 11-13 Counters (Port) Window...
Page 417 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-14 Counters (Show Detail) Window Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table.
Page 418: Mirror Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-15 Counters (VLAN) Window The fields that can be configured are described below: Parameter Description Type Select the type of information to display here. Options to choose from are Port and VLAN.
Page 419 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-16 Mirror Settings Window The fields that can be configured for RSPAN VLAN Settings are described below: Parameter Description VID List Enter the VLAN list’s ID(s) that will be associated with this configuration here.
Page 420: Sflow
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description outgoing direction will be mirrored. When selecting TX Forwarding, traffic in only the outgoing direction will be mirrored and forwarded. Select the CPU RX option to also monitor CPU traffic.
Page 421: Sflow Receiver Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-18 sFlow Agent Information Window sFlow Receiver Settings This window is used to display and configure receivers for the sFlow agents. Receivers cannot be added to or removed from the sFlow agent.
Page 422: Sflow Poller Settings
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-20 sFlow Sampler Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 423: Device Environment
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. Select the appropriate port range used for the configuration here.
Page 424 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 11-23 External Alarm Settings Window The fields that can be configured in External Alarm Trap Settings are described below: Parameter Description External Alarm Trap State Select to enable or disable the external alarm trap state here.
Page 425: 12. Green
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide 12. Green Power Saving Power Saving This window is used to configure the power saving settings of the Switch. To view the following window, click Green > Power Saving, as shown below:...
Page 426: Eee
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: The hibernation feature can only be configured when physical stacking is disabled on the Switch. After clicking the Power Saving Shutdown Settings tab, the following page will appear.
Page 427 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port ~ To Port Select the appropriate port range used for the configuration here.
Page 428: 13. Save And Tools
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide 13. Save and Tools Save Configuration Firmware Upgrade & Backup Configuration Restore & Backup Log Backup Ping Trace Route Reset Reboot System DLMS Settings Save Configuration This window is used to save the running configuration to the start-up configuration. This is to prevent the loss of configuration in the event of a power failure.
Page 429: Firmware Upgrade From Tftp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. Source File In this field the source firmware file’s filename and path will be displayed after selection.
Page 430: Firmware Upgrade From Rcp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 13-4 Firmware Upgrade from FTP Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 431: Firmware Backup To Http
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description RCP Server IP Enter the RCP server’s IP address here. User Name Enter the user name used for the RCP connection here. This name can be up to 32 characters long.
Page 432: Firmware Backup To Ftp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. TFTP Server IP Enter the TFTP server’s IP address here. When select the IPv4 option, enter the IPv4 address of the TFTP server in the space provided.
Page 433: Firmware Backup To Rcp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Firmware Backup to RCP This window is used to initiate a firmware backup to an RCP server. To view the following window, click Tools > Firmware Upgrade & Backup > Firmware Backup to RCP, as shown...
Page 434: Configuration Restore From Tftp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description selection. To navigate to the location of the configuration file located on the local PC, either double click in the text box or click the Browse button.
Page 435: Configuration Restore From Rcp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 13-12 Configuration Restore from FTP Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 436: Configuration Backup To Http
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. RCP Server IP Enter the RCP server’s IP address here.
Page 437: Configuration Backup To Ftp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 13-15 Configuration Backup to TFTP Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 438: Configuration Backup To Rcp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description User Name Enter the user name used for the FTP connection here. This name can be up to 32 characters long. Password Enter the password used for the FTP connection here. This password can be up to 15 characters long.
Page 439: Log Backup To Tftp
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To view the following window, click Tools > Log Backup > Log Backup to HTTP, as shown below: Figure 13-18 Log Backup to HTTP Window The fields that can be configured are described below:...
Page 440: Ping
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 13-20 Log Backup to RCP Window The fields that can be configured are described below: Parameter Description RCP Server IP Enter the RCP server’s IP address here.
Page 441 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Figure 13-21 Ping Window The fields that can be configured in Ping Access Class are described below: Parameter Description ACL Name Enter the name of the ACL that will be used here. This name can be up to 32 characters long.
Page 442 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Click the Start button to initiate the Ping Test for each individual section. The fields that can be configured in IPv6 Ping are described below: Parameter Description Target IPv6 Address Enter an IPv6 address to be pinged.
Page 443: Trace Route
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trace Route The trace route page allows the user to trace a route between the Switch and a given host on the network. To view the following window, click Tools > Trace Route, as shown below:...
Page 444: Reset
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Parameter Description option will cross while seeking the network path between two devices. The range for the TTL is 1 to 255 hops. Port Enter the port number here. The value range is from 1 to 65535.
Page 445: Dlms Settings
Figure 13-28 Reboot System (Rebooting) Window DLMS Settings This window is used to display and configure the D-Link License Management System (DLMS) settings. The license specifies the feature options that are enabled on the Switch. License keys are sold in the market. It may be printed on a physical package or be displayed in an e-mail or a portal.
Page 446: Appendix A - Password Recovery Procedure
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Appendix A - Password Recovery Procedure This section describes the procedure for resetting passwords on the D-Link DXS-3400 Series Switch. Authenticating any user who tries to access networks is necessary and important. The basic authentication method used to accept qualified users is through a local login, utilizing a Username and Password.
Page 447: Appendix B - System Log Entries
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Appendix B - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of the Switch.
Page 448 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: Login failed due to AAA server timeout or improper configuration. Warning Log Message: Login failed through <exec-type> from <client-ip> due to AAA server <server-ip>...
Page 449 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity username: It indicates the username for authentication. Event description: RADIUS assigned a valid priority attributes. Informational Log Message: RADIUS server <server-ip> assigned 802.1p default priority: <priority> to port <...
Page 450 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: Cross-connect is detected Critical Log Message: CFM cross-connect. VLAN:<vlanid>, Local(MD Level:<mdlevel>, Interface:<interface-id>, Direction:<mepdirection>) Remote(MEPID:<mepid>, MAC:<macaddr>) Parameters description: vlanid: Represents the VLAN identifier of the MEP.
Page 451 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity mdlevel: Represents the MD level of the MEP. interface-id: Represents the interface number of the MEP. mepdirection: Represents the MEP direction, which can be "inward" or "outward".
Page 452 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: Firmware upgraded successfully. Informational Log Message: [Unit <unitID>, ]Firmware upgraded by <session> successfully (Username: <username>[, IP: <ipaddr>, MAC: <macaddr>], Server IP: <serverIP>, File Name: <pathFile>)
Page 453 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Name: <pathFile>) Parameters description: unitID: The unit ID. session: The user’s session. username: Represent current login user. ipaddr: Represent client IP address. macaddr : Represent client MAC address.
Page 454 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity session: The user’s session. username: Represent current login user. ipaddr: Represent client IP address. macaddr : Represent client MAC address. serverIP: Server IP address.
Page 455 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity TX power RX power high-low: High or low threshold. Event description: when the any of SFP parameters recovers from the warning threshold. Warning Log Message: Optical transceiver <interface-id> <component> back to normal.
Page 456 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Parameters description: ipv6address: ipv6 address obtained from a DHCPv6 server. ipif-name: Name of the DHCPv6 client interface.. Event description: The ipv6 address from a DHCPv6 server was deleted.
Page 457 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide DHCPv6 Relay Log Description Severity Event description: DHCPv6 relay on a specify interface’s administrator state changed Informational Log Message: DHCPv6 relay on interface <ipif-name> changed state to [enabled |...
Page 458 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide DNS Resolver Log Description Severity Event description: Duplicate Domain name cache added, leads a dynamic domain name Informational cache be deleted Log Message: [DNS_RESOLVER(1):]Duplicate Domain name case name: <domainname>, static IP: <ipaddr>, dynamic IP:<ipaddr>...
Page 459 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity vlanid: VLAN ID interface-id: Interface name Ethernet OAM Log Description Severity Event description: Dying gasp event(remote) Warning Log Message: OAM dying gasp event received (Port<interface-id>) Parameters description: interface-id: The interface name.
Page 460 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Interface Log Description Severity Event description: Port link up. Informational Log Message: Port <portNum> link up, <link state> Parameters description: portNum: 1.Interger value;2.Represent the logic port number of the device.
Page 461 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event Description: Port recovered from LBD blocked state under port-based mode. Informational Log Message: Port< [unitID:] portNum> LBD port recovered. Loop detection restarted. Parameters Description: unitID: The unit ID.
Page 462 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity 3. macAddress(3) 4. networkAddress(4) 5. interfaceName(5) 6. agentCircuitId(6) 7. local(7) portID: port ID. deviceClass: LLDP-MED device type. Event description: Conflict LLDP-MED device type detected Notice Log Message: Conflict LLDP-MED device type detected ( on port <...
Page 463 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Value list: 1. interfaceAlias(1) 2. portComponent(2) 3. macAddress(3) 4. networkAddress(4) 5. interfaceName(5) 6. agentCircuitId(6) 7. local(7) portID: port ID. deviceClass: LLDP-MED device type. Login/Logout...
Page 464 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: Telnet session timed out. Informational Log Message: Telnet session timed out (Username: <username>, IP: <ipaddr | ipv6address>) Parameters description: username: Represent current login user.
Page 465 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity mac-address: the host MAC addresses. interface-id: the interface on which the host is authenticated. vlan-id: the VLAN ID on which the host exists. Event description: the host has aged out.
Page 466 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity InstanceID: Instance ID. macaddr: Mac address value: priority value Event description: Spanning Tree Protocol is enabled Informational Log Message: Spanning Tree Protocol is enabled...
Page 467 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Parameters description: InstanceID: Instance ID. startvlanid- endvlanid: VLANlist Event description: Spanning Tree MST configuration ID VLAN mapping table added. Informational Log Message: Spanning Tree MST configuration ID VLAN mapping table changed (instance: <InstanceID>...
Page 468 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Log Message: Unit <unitID> External Alarm Channel < channelID> :< alarmMsg > Parameters description: unitID: The unit ID. channelID: The channel ID. alarmMsg: The alarm Msg.
Page 469 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity enters normal mode, and the syslog will be recorded. Log Message: Unit <unit-id>, Safeguard Engine enters NORMAL mode. Parameters description: unit-id: Unit ID. SNMP...
Page 470 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Log Message: Unit: <unitID>, MAC: <macaddr> Hot removal. Parameters description: unitID: Box ID. Macaddr: MAC address. Event description: Stacking topology change. Informational Log Message: Stacking topology is <Stack_TP_TYPE>. Master(Unit <unitID>, MAC:<macaddr>).
Page 471 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Unicast> storm. Parameters description: interface-id: The interface ID on which is error-disabled by storm. Broadcast: The interface is disabled by broadcast storm. Multicast: The interface is disabled by multicast storm.
Page 472 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Parameters description: vr-id: VRRP virtual router ID. intf-name: Interface name on which virtual router is based. Event description: Authentication type mismatch of one received VRRP advertisement Warning message.
Page 473 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: A virtual MAC address is deleting from switch L3 table. Notice Log Message: Deleted a virtual IP <vrrp-ip-addr> MAC <vrrp-mac-addr> from L3 table...
Page 474 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Parameters description: vrrp-ip-addr: VRRP virtual IP address vrrp-mac-addr: VRRP virtual MAC address vrrp-errcode: Err code of VRRP protocol behavior. Event description: Failed when deleting a virtual MAC from switch chip’s L3 table.
Page 475 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Log Description Severity Event description: Successful login through Web. Informational Log Message: Successful login through Web (Username: <username>, IP: <ipaddr>). Parameters description: username: The username that used to login HTTP server.
Page 476: Appendix C - Trap Entries
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Appendix C - Trap Entries The following table lists all possible trap log entries and their corresponding meanings that will appear in the Switch. 802.1X Trap Name...
Page 477 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description dot1agCfmFaultAlarm This trap is initiated when a connectivity defect is 1.3.111.2.802. detected. 1.1.8.0.1 Binding objects: (1) dot1agCfmMepHighestPrDefect CFM Extension Trap Name Description dCfmAisOccurred This trap is initiated when local MEP enters AIS status.
Page 478 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description (3) dDdmNotifyInfoAbnormalLevel (4) dDdmNotifyInfoThresholdExceedOrRecover DHCP Server Screen Prevention Trap Name Description dDhcpFilterAttackDetected When DHCP Server Screen is enabled, if the Switch 1.3.6.1.4.1.171 received the forge DHCP Server packet, the Switch will .14.133.0.1...
Page 479 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Gratuitous ARP Trap Name Description agentGratuitousARPTrap The trap is sent when IP address conflicted. 1.3.6.1.4.1.171 .14.75.0.1 Binding objects: (1) ipaddr (2) macaddr (3) portNumber (4) agentGratuitousARPInterfaceName IP-MAC-Port Binding...
Page 480 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description dL2FdbMacNotification This trap indicates the MAC addresses variation in the 1.3.6.1.4.1.171 address table. .14.3.0.1 Binding objects: (1) dL2FdbMacChangeNotifyInfo MAC-based Access Control Trap Name Description...
Page 481 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description (1) dot3OamEventLogTimestamp (2) dot3OamEventLogOui (3) dot3OamEventLogType (4) dot3OamEventLogLocation (5) dot3OamEventLogWindowHi (6) dot3OamEventLogWindowLo (7) dot3OamEventLogThresholdHi (8) dot3OamEventLogThresholdLo (9) dot3OamEventLogValue (10) dot3OamEventLogRunningTotal (11) dot3OamEventLogEventTotal dot3OamNonThresholdEvent This notification is sent when a local or remote non- 1.3.6.1.
Page 482 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description linkUp A notification is generated when port linkup. 1.3.6.1.6.3.1.1. Binding objects: (1) ifIndex, (2) if AdminStatus (3) ifOperStatus linkDown A notification is generated when port linkdown.
Page 483 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description dSafeguardChgToExhausted This trap indicates System change operation mode from 1.3.6.1.4.1.171 normal to exhaust. .14.19.1.1.0.1 Binding objects: (1) dSafeguardEngineCurrentMode dSafeguardChgToNormal This trap indicates system change operation mode from 1.3.6.1.4.1.171...
Page 484 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Start Trap Name Description coldStart A coldStart trap signifies that the SNMPv2 entity, acting in 1.3.6.1.6.3.1.1. an agent role, is reinitializing itself and that its configuration may have been altered.
Page 485 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Trap Name Description Binding objects: (1) unitID (2) agentCfgOperate (3) agentLoginUserName VRRP Trap Name Description vrrpTrapNewMaster The newMaster trap indicates that the sending agent has 1.3.6.1.2.1.68. transitioned to 'Master' state.
Page 486: Appendix D - Radius Attributes Assignment
DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide Appendix D - RADIUS Attributes Assignment The RADIUS Attributes Assignment on the Switch is used in the following modules: Console, Telnet, SSH, Web, 802.1X, MAC-based Access Control, and WAC.
Page 487 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide To assign the 802.1p Default Priority by the RADIUS server, the proper parameters should be configured on the RADIUS server. The table below shows the parameters for 802.1p default priority.
Page 488 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide NOTE: A tag field of greater than 0x1F is interpreted as the first octet of the following field. If the user has configured the VLAN attribute of the RADIUS server (for example, VID 3) and the 802.1X, or MAC based Access Control, or WAC authentication is successful, the port will be assigned to VLAN 3.
Page 489: Appendix E - Ietf Radius Attributes Support
Switch. RADIUS attributes are supported by the IETF standard and Vendor-Specific Attribute (VSA). VSA allows the vendor to create an additionally owned RADIUS attribute. For more information about D-Link VSA, refer to the RADIUS Attributes Assignment Appendix.
Page 490 DXS-3400 Series Lite Layer 3 Stackable 10GbE Managed Switch Web UI Reference Guide RADIUS Accounting Attributes: Number IETF Attribute User-Name NAS-IP-Address NAS-Port Service-Type Framed-IP-Address Calling-Station-ID NAS-Identifier Acct-Status-Type Acct-Delay-Time Acct-Input-Octets Acct-Output-Octets Acct-Session-ID Acct-Authentic Acct-Session-Time Acct-Input-Packets Acct-Output-Packets Acct-Terminate-Cause Acct-Input-Gigawords Acct-Output-Gigawords NAS-Port-Type NAS-IPv6-Address...

D-Link DXS-3400 SERIES Web Ui Reference Manual

1 Introduction

2 Web-Based Switch Configuration

3 System

4 Management

5 Layer 2 Features

6 Layer 3 Features

7 Quality of Service (Qos)

8 Access Control List (ACL)

9 Security

Quick Links

Related Manuals for D-Link DXS-3400 SERIES

Summary of Contents for D-Link DXS-3400 SERIES