5.6 Pin Layout Life Connector ..................13 5.7 Pin Layout Sensor Connector ................15 6 Mechanical drawing ..................... 16 7 Starting up the C 60 ..................... 17 7.1 Start-Up ......................... 18 7.2 Feature activation ....................29 7.3 My first recording ....................34 8 Details of the C 60 ....................
1 Getting started Important Notes: Use the C 60 only as intended in this manual. Any maintenance or repair must be performed by authorized and qualified personnel approved by Bosch Motorsport. Operation of the C 60 is only certified with the combinations and accessories that are specified in this manual.
Be careful to observe current limits of wires and connector pins! 3 Onboard network concept IGN- Switch UBAT Star connection switched pos. terminal (term30) positive terminal Electric Loads Main KL15 Switch C 60 KL30 Bosch Motorsport diagnosis connector µC LS_SWITCH1…4 KL31 UBATT_FUSE GND_Starpoint SENSPWR10 Star connection Chassis dig. sensors (e.g.
Ethernet or via wireless connection with the BT 60 burst telemetry system. As a base system the C 60 is sold as data logger only. A software upgrade for the C 60 (field upgradable by entering a key) activates additional input channels.
Page 6
Technical data C 60 Feature List C 60 Base Logger Software Upgrade 1 Application 2 GB 2 GB Storage capacity • • BT 60 burst telemetry support • • FM 40 long range telemetry support • GPS input Electrical Data 8 …...
5 Inputs and Outputs Input Channels 5.1.1 Analog Inputs The C 60 analog inputs accept an input signal of 0 to 5 V. A 3.01 kOhm pull-up resistor can be activated by software. 5.1.2 Digital Inputs The digital input of the C 60 accept 0 V to 5 V signals of Hall-effect sensors by default. Connect the output of the Hall-effect sensor to the REVn_P pin and leave the REVn_M pin open.
Ethernet switch. The ethernet ports have 'cable auto crossover' functionality. 5.3.3 RS232 Ports The C 60 has two RS232 serial ports. Baudrate for both ports is programmable. RS232 port 1 is reserved for online telemetry, port 2 can be used for reception of data from a serial GPS receiver.
Inputs and Outputs Sensor recommendation Clubsport The sensors shown on this page are partly based on production type parts and proved hundreds of times in races all over the world. They offer good value for money. NTC M12-L NTC M12-H TCP-NF PSA-C PSS-10...
Page 10
Inputs and Outputs AM 600-3 YRS 3 Model Range of application Connector Loom Part No. NTC_M12-L Ambient air temperature D 261 205 288 0 280 130 039 NTC-M12-H Fluid temperature (oil, water, fuel) D 261 205 337 0 281 002 170 TCP-NF Exhaust gas temperature D 261 205 357...
Inputs and Outputs Sensor recommendation Professional A lot of the sensors shown on this page are developed for high end applications. You can find more motorsports sensors at www.bosch-motorsport.com NTC M8-HS TCP-NF TI-100 PSA-C PSC-10 PSB-4 Mini-HA-P HA-M RP 100...
Page 12
Inputs and Outputs AM 600-3 YRS 3 Model Range of application Connector Loom Part No. NTC M8-HS Fluid temperature (oil, water, fuel) ASL 0-06-05SN-HE F 02U V00 509 TCP-NF Exhaust gas temperature D261 205 357 B 261 209 825 T-100 Brake disk and tire temperature ASL 0-06-05SD-HE F 01T A21 210...
Inputs and Outputs Pin Layout Life Connector Life Connector ASDD-2-12-41PN (Red) Name Description Direction Remark UBATT power supply Ubat input switched positive Kl.15 switched power supply Ubat input switched positive Kl.15 switched power supply Ubat input unit ground ground power supply input unit ground ground power supply...
Page 14
Inputs and Outputs Name Description Direction Remark ANA06 analog signal 6 input...
Inputs and Outputs Pin Layout Sensor Connector Sensor Connector ASDD-2-12-41PA (Yellow) Name Description Direction Remark UBATT_FUSE1 battery voltage supply output SENSPWR10_1 10 V power supply for analog sensors output SENSPWR5_2 5 V power supply for analog sensors output SENSPWR5_3 5 V power supply for analog sensors output SENSPWR5_4 5 V power supply for analog sensors...