Related Manuals for 4IPNET EAP220
Summary of Contents for 4IPNET EAP220
- Page 1 EAP220 Enterprise Access Point...
-
Page 2: Copyright Notice
4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations. -
Page 3: Fcc Caution
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Copyright © 4IPNET, INC. All rights reserved. - Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
-
Page 5: Package Contents
EAP220 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP220 is a high-end 802.11a/b/g/n 2.4GHz/ 1. 4ipnet EAP220 x 1 5GHz MIMO Access Point (AP) with two RF cards 2. Quick Installation Guide (QIG) x 1 (2.4GHz RF Card A / 5GHz RF Card B) embedded 3. -
Page 6: System Overview
(Green) (Green) WES Success LED (Green) ON LED (Green) ON WES Fail/Timeout LED (Green) OFF LED (Green) OFF On indicates wireless network interface is ready for service. Wireless LED (2.4 / 5 GHz) Copyright © 4IPNET, INC. All rights reserved. - Page 7 5 seconds. For IT administrators to easily setup WDS links with two RF cards. WES Button (RF B) To access EAP220 via the console interface. Console port LAN 1 - 4 ports The ports for connections with LAN side devices.
-
Page 8: Hardware Installation
2. Connect EAP220 to your network device. Connect one end of the Ethernet cable to the Uplink port of EAP220 and the other end of the cable to a switch, a router or a hub. EAP220 is then connected to your existing wired LAN network. -
Page 9: Getting Started
1. To access the Web Management Interface, connect the administrator PC to the LAN port of EAP220 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP220 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 10 EAP220 Enterprise Access Point ENGLISH 4. After a successful login to EAP220, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status for modules on both RF cards will be shown.
-
Page 11: Common Settings
Click on the Utilities icon on the main menu, and select the Change Password tab. Enter a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved. - Page 12 Determine the Band, Protocol and Channel settings: Select your preferred Band, Protocol and Channel for you wireless connection. For example, select 2.4GHz for the band, 802.11g+802.11n for the protocol and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
- Page 13 ENGLISH Admin should be aware of Dynamic Frequency Selection (DFS) mandated on some channels of the 5GHz band. When an EAP220 detects interference, this mechanism will limit the ability to broadcast the SSID on one of the channels listed below: ...
- Page 14 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (RF Card A : VAP-1 shown) EAP220 supports up to 16 virtual APs (VAPs) per RF Card. Configure VAP profile settings： (a) Select the VAP Config tab to configure the settings of the desired VAP.
- Page 15 Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Virtual AP Overview Page Copyright © 4IPNET, INC. All rights reserved.
- Page 16 Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP220 supports up to 8 WDS links per RF card for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled.
- Page 17 Congratulations! Now, 4ipnet EAP220 is installed and configured successfully. After EAP220's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments.