ERROR MESSAGES (エラーメッセージ) ......44 SYSTEM BOOTING FLOWCHART (起動フローチャート)............ 45/46 MIDI IMPLEMENTATION CHART .......... 47 MIDI DATA FORMAT ............. 48 PARTS LIST BLOCK DIAGRAM (ブロックダイアグラム) OVERALL CIRCUIT DIAGRAM (総回路図) u163 011849 HAMAMATSU, JAPAN 20061215-オープンプライス Copyright (c) Yamaha Corporation. All rights reserved. PDF ’06.12 http://www.xiaoyu163.com...
3 7 63 1515 0 IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
Dimensions (W x D x H) 252 x 147 x 52 mm (9-15/16" x 5-13/16" x 2-1/16") Weight 898 g (2 lbs.) Accessories Yamaha AC power adaptor (PA-3C), Module stand, Module stand fastening screws x 2 Owner's Manual u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 CONNECTING THE PADS(パッドの接続) Standard Set (スタンダードセット) DTXPRESS L 13942296513 DTXPRESS Special Set (スペシャルセット) u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 DISASSEMBLY PROCEDURE(分解手順) Caution: 注意事項 Pay attention not to insert and install the cable to フラットケーブルの表 ・ 裏を逆に差し込まないように 注意して取り付けてください。 ( 図A) the connector inversely. (Fig. A) Fig. A (図A) Front Side (Printed Side) Back Side 表面...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 LSI PIN DESCRIPTION(LSI 端子機能表) HG73C205AFDV (XU947C00) SWX00B (Tone Generator) DM: IC16 NAME FUNCTION NAME FUNCTION Initial clear CMA3 Program address bus RFCLKI PLL Clock CMA8 Program address bus PLL Control CMA2 Program address bus AVDD_PLL Power supply read signal...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 AK4385ET (X6040A00) DAC (Digital to Analog Converter) DM: IC15 NAME NAME FUNCTION FUNCTION AOUTR- Rch Analog out(-) MCLK Master Clock AOUTR+ Rch Analog out(+) BICK Audio Serial Data Clock AOUTL- SDTI Audio Serial Date Input Lch Analog out(-) AOUTL+ Lch Analog out(+)
Page 13
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 µPC4570G2-E1-A (X7351A00) SN74AHC1G08DCKR (X3833A00) SN74AHC1G04DCKR (X4137A00) Single 2-Input Positive-AND Gate Inverter Gate NJM4556AM-TE1 (X5049A00) Dual Operational Amplifier DM: IC29 DM: IC30–32 DM: IC14 PN: IC304, 310, 309, 312 +DC Voltage Output A IN A Supply Inverting Output B...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 CIRCUIT BOARDS(シート基板図) Note : See parts list for details of circuit board component parts. DM Circuit Board (注:シートの部品詳細は、パーツリストをご参照ください。 ) L 13942296513 u163 Component side (部品側) 2NA-WH02300-1 3 http://www.xiaoyu163.com...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 TEST PROGRAM Title Outline A. Test entry B. Carrying on the test (when the test result is FAIL as well) C. Test item C-01. ROM Program ROM READ check C-02. FLASH FLASH ROM READ/WRITE check C-03.
Page 19
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 How to carry on the test when the test result is FAIL Test entry When the test is judged as FAIL, press the [SHIFT] key, and While pressing the [DRUM KIT] and [SAVE/ENTER] keys [A0 XX 03] (XX represents each test code) is output from MIDI simultaneously, turn on the power to the DTXPRESS OUT and the screen changes to the [Test number select screen].
Page 20
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-01. ROM C-02. FLASH [Test code] [Test code] [Initial indication] [Initial indication] 1 ROM 2 FLASH [Test content] [Test content] Read the P2ROM data and verify it. Check the manufacture code and device ID of FLASH ROM. [Test method] [Test method] Press the [SAVE/ENTER] key to execute the test.
Page 21
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-03. SRAM C-04. MIDI [Test code] [Test code] [Initial indication] [Initial indication] 3 SRAM 4 MIDI [Test content] [Test content] Write/read the data "AA" and "55"in the SRAM area and verify Output key on (90 3C 7F) from MIDI OUT. After 500msec., them.
Page 22
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-05. LCD C-06. LED [Test code] [Test code] [Initial indication] [Initial indication] 5 LCD 6 LED [Test content] [Test content] Check dots of LCD visually. Check that LEDs light properly. [Test method] [Test method] Press the [SAVE/ENTER] key to execute the test.
Page 23
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-07. 7SEG LED C-08. SW [Test code] [Test code] [Initial indication] [Initial indication] 7 7SEGLED 8 SW [Test content] [Test content] Check that 7 segment LEDs light properly. Check that he panel switches turns ON/OFF properly. [Test method] [Test method] Press the [SAVE/ENTER] key to execute the test.
Page 24
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-09. R.Encoder C-10 PAD.Encoder [Test code] [Test code] [Initial indication] [Initial indication] 9 R.Encoder 10 PAD.Encoder [Test content] [Test content] Check that the rotary encoder (Jog dial) operates properly. Check that operation of the pad encoder is recognized properly. [Test method] [Test method] 1.
Page 25
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 [Content of FAIL judgment] Set VOLUME to MAX. Input the signal output from PHONES None in the following order. q SNARE Lch→w TOM1/10 Lch→wTOM1/10 Rch→ eTOM2/11 Lch→eTOM2/11 Rch→rTOM3/12 Lch→ [MIDI code output of judgment result] r TOM3/12 Rch→t RIDE Lch→y CRASH Lch→...
Page 26
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-23. RIM SW IN 01, C-24. RIM SW L IN 01, [Indication of judgment result] C-25. RIM SW IN 05, C-26. RIM SW L IN 05, When the result is OK, checking proceeds to the next switch C-27.
Page 27
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-31. OUTPUT L 1kHz 30 H.H. CONT. [Test code] [Depress] [Initial indication] 30 H.H. CONT. MIN- 0 31 OUTPUT L 1kHz [Release] [Test content] To the next test Check that correct signal is being outputted from OUTPUT (L/ MONO).
Page 28
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-32. OUTPUT R 1kHz C-33. AUX INPUT [Test code] [Test code] [Initial indication] [Initial indication] 32 OUTPUT R 1kHz 33 AUX INPUT [Test content] [Test content] This test checks that correct signal is outputted from OUTPUT This test checks that the output signal which is inputted from (R).
Page 29
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-34. 32ch OUT C-35. FACTORY SET [Test code] [Test code] [Initial indication] [Initial indication] 34 32 ch OUT 35 FACTORY SET [Test content] [Test content] This test checks that sound is output from 32 channels properly, Initialize the data to the factory setting.
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 2-2. Press the [PAGE ] button several times to call up the Inspecting the Unit for Sound Production UTIL8 page. 1. In the normal operation state, set VOLUME to MAX and UTIL8 check that the noise level meets following conditions. π...
Page 31
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 ■ テストプログラム 表題 概要 A. テストエントリー B. テストの進め方、及び FAIL 時の進め方 C. テスト項目 Program ROM READ check C-01. ROM C-02. FLASH FLASH ROM READ/WRITE check C-03. SRAM SRAM READ/WRITE check C-04. MIDI MIDI OUT output key on/off check C-05.
Page 39
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 C-23. RIM SW IN 01, C-24. RIM SW L IN 01, [判定結果の表示] C-25. RIM SW IN 05, C-26. RIM SW L IN 05, OKの時 C-27. RIM SW IN 06, C-28. RIM SW L IN 06, 次のスイッチのチェックへ、...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 ERROR MESSAGES(エラーメッセージ) The DTXPRESS displays error messages when 設定や操作が正しくない場合や、 動作において異常が発生し incorrect settings have been made or invalid た場合、 LCDディスプレイ(画面)にエラーメッセージが表示さ operations have been detected, or when any abnormal れます。 operation or malfunction occurs. エラーメッセージの内容を確認し、 正しく設定/操作するな If an error message appears, check the list below and ど、...
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 SYSTEM BOOTING FLOWCHART (Sequence to turn on the power) Turning on the power while pushing each of following switches results in the corresponding function. • [SHIFT] ..........Version indication • [PAGE ] + [PAGE ] .......
http://www.xiaoyu163.com DTXPRESS 3 7 63 1515 0 MIDI DATA FORMAT 1. Channel Messages The channel messages described below are sent from the drum triggers only. Other messages are sent from both the drum triggers and the sequencer. 1.1 Key On, Key Off Note range: 0 (C-2)–127 (G8) Velocity range: 0–127 1.2 Control Change...
Page 49
http://www.xiaoyu163.com 3 7 63 1515 0 DRUM TRIGGER MODULE PARTS LIST CONTENTS(目次) OVERALL ASSEMBLY(総組立)............2 ELECTRICAL PARTS(電気部品)..........4–11 L 13942296513 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model...
Page 61
http://www.xiaoyu163.com <Page 1> DTXPRESS DTXPRESS OVERALL CIRCUIT DIAGRAM 1/3 (DM 1/2) to DM 2/2 not installed <Page 2 M-9> P2ROM 128M PROGRAM & WAVE to PN-CN306 <Page 3 P-10> INVERTER GATE GATE to PN-CN305 <Page 3 P-8> not installed S-BUS POWER not installed not installed...
Page 62
http://www.xiaoyu163.com <Page 2> DTXPRESS DTXPRESS OVERALL CIRCUIT DIAGRAM 2/3 (DM 2/2) to DM 1/2 <Page 1 O-6> OP AMP to DM 1/2 <Page 1 G-10> OP AMP t RIDE OP AMP OP AMP OP AMP OP AMP OP AMP y CRASH OP AMP INVERTER OP AMP...
Page 63
http://www.xiaoyu163.com <Page 3> DTXPRESS DTXPRESS OVERALL CIRCUIT DIAGRAM 3/3 (PN) OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP not installed not installed OP AMP OP AMP OP AMP not installed not installed OP AMP OP AMP OP AMP q SNARE D-FF...