Page 1 DVS-9000/9000SF System (With CCP-9000 Series Center Control Panel) User’s Guide Production Switcher System [English] Volume 2 1st Edition Software Version 1.30 and Later...
Page 2 NOTICE TO USERS © 2002 Sony Corporation. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval from Sony Corporation.
Page 3: Table Of Contents
Table of Contents Chapter 11 DME Operations Chapter 12 External Devices Basic Operation for External Device Control..........10 Saving Control Setting Data in Registers..........10 Amending Keyframes................11 Carrying Out Control of External Devices..........12 Control of P-BUS Devices ................14 Editing the P-BUS Timeline..............14 P-BUS Trigger..................16 Chapter 13 Keyframe Effects Sequence of Keyframe Operations..............20...
Page 4 Register Operations in the Menus...............46 Effect Status Display ................46 Effect Register Editing ................46 Chapter 14 Snapshots Snapshot Operations From the Numeric Keypad Control Block ....50 Saving and Recalling Snapshots............51 Snapshot Operations in the Menus .............55 Setting Snapshot Attributes ..............55 Snapshot Status Display ................57 Setting Key Snapshot Attributes ............58 Snapshot Register Editing ..............58 Chapter 15 Shot Box...
Page 5 Signal Output Settings (Output Menu)..........107 Settings Relating to Video Switching (Transition Menu) ....110 Settings Relating to Keys, Wipes and Frame Memory (Key/Wipe/FM Menu) ..................112 Settings Relating to Function Links (Link Menu).......114 Interfacing With External Devices (Device Interface Menu)....118 Setup Relating to DME ................123 Settings Relating to Signal Inputs (Input Menu).........123 Interfacing With External Devices (Device Interface Menu)....124 Setup Relating to DCU ................127...
Page 6 Chapter 18 DIAGNOSIS Appendix Wipe Pattern List ..................160 Standard Wipes..................160 Enhanced Wipes ..................161 Rotary Wipes ..................162 Mosaic Wipes ..................163 Random/Diamond Dust Wipes............165 DME Wipe Pattern List ................166 DME Wipe Patterns Available in One-Channel Mode .......166 DME Wipe Patterns Available in Two-Channel Mode.......170 Menu Tree ....................171 Recalling Menus..................171 M/E-1 to M/E-3 Menus ...............171...
Page 7: Chapter 11 Dme Operations
Chapter 11 DME Operations Not supported in version 1.30.
Page 9 Chapter 12 External Devices Basic Operation for External Device Control ........10 Saving Control Setting Data in Registers ........10 Amending Keyframes..............11 Carrying Out Control of External Devices ........12 Control of P-BUS Devices ..............14 Editing the P-BUS Timeline............14 P-BUS Trigger .................
Page 10: Basic Operation For External Device Control
Basic Operation for External Device Control Use the Device menu to carry out operations for controlling external devices such as devices supporting P-BUS (Peripheral II protocol) (referred to as “P- BUS devices” in the manual), and VTRs. For VTRs only, you can also carry out operations using the device control block.
Page 11: Amending Keyframes
e: This register is empty in the selected region. E: This register is empty in all selectable regions. Press the [ENTER] button. This recalls the register you selected in step 4. In the Device menu, press VF2 ‘P-BUS Timeline.’ The Device>P-Bus Timeline menu appears. The status area shows a window for setting the action for the P-BUS device.
Page 12: Carrying Out Control Of External Devices
Press the [P-BUS] button in the numeric keypad control block, turning it on, to select the P-BUS region. Enter the number of the register to be recalled, with the numeric keypad buttons. Using the edit point specification buttons and fader lever in the keyframe control block, stop the effect on the desired edit point.
Page 13 To move to the first keyframe To move to the first keyframe, press the [REWIND] button in the keyframe control block. If an action is set for a rewind operation, then the action is carried out. (See “Setting an action for the rewind operation” (page 16).) Basic Operation for External Device Control...
Page 14: Control Of P-Bus Devices
Control of P-BUS Devices Editing the P-BUS Timeline This section describes how to set an action for a keyframe point, and edit the P-BUS timeline. Note Using the P-BUS timeline function requires the P-BUS control mode to be set to [Timeline]. Carry out this setting in the Engineering Setup>Panel>Device Interface menu.
Page 15 3: Recall 4: Trigger If in step 3 you selected 2 (Store), 3 (Recall), or 4 (Trigger), turn knob 3 to select the register number or trigger number. The indication for knob 3 changes to reflect the selection of Store, Recall, or Trigger.
Page 16: P-Bus Trigger
Setting an action for the rewind operation In order that when recalling a P-BUS timeline, pressing the [REWIND] button in the keyframe control block moves to the first keyframe, an action setting must be made for this. In the Device>P-Bus Timeline menu, press [Rewind Action], and make the setting in the window that appears.
Page 17 Press the [P-BUS] button in the numeric keypad control block, turning it on, to select the P-BUS region. Enter the number of the register to be recalled with the numeric keypad buttons. Press the [ENTER] button in the numeric keypad control block. This carries out the Recall.
Page 18 Control of P-BUS Devices...
Page 19: Chapter 13 Keyframe Effects
Chapter 13 Keyframe Effects Sequence of Keyframe Operations............20 Recalling a Register ................21 Specifying the Region and Edit Points..........23 Creating and Editing Keyframes ............25 Creation ................... 25 Insertion ................... 26 Modification ..................26 Deletion ................... 30 Movement..................31 Copying ...................
Page 20: Sequence Of Keyframe Operations
Sequence of Keyframe Operations The following table shows the principal operations involved in the sequence from creating keyframes to executing an effect. For details of each operation, see the page number in parenthesis. For an overview, see “Keyframes” in Chapter 1 (Volume 1). Recalling a register (see page 21) To create a new effect, recall an empty register;...
Page 21: Recalling A Register
Recalling a Register Use the numeric keypad control block to recall a register. For each region there are 99 registers dedicated to keyframes, numbered from 1 to 99. When creating an effect as a user programmable DME, use a 3-digit register number which is commonly used for all DME regions (channels).
Page 22 Press the [EFF] button, turning it on. This allocates the numeric keypad control block to keyframe operations, and the [RCALL] button lights. Press the button corresponding to the region you want to select, turning it You can also press more than one button. [M/E 1], [P/P]: These select the corresponding M/E-1 and PGM/PST regions.
Page 23: Specifying The Region And Edit Points
Specifying the Region and Edit Points Selecting the region in which editing applies Select the region in which the editing is applied by the effect consisting of keyframes, using the region selection buttons in the numeric keypad control block. (See step 2 in “Recalling a register” on the previous page.) Setting the edit points EDIT ENBL button CONST DUR button...
Page 24 • To move the edit point to a keyframe specified by number, press the [GO TO KF/TC] button, turning its LED on, then enter the keyframe number with the numeric keypad in the numeric keypad control block, and press the [ENTER] button to confirm.
Page 25: Creating And Editing Keyframes
Creating and Editing Keyframes For details of keyframe editing, see “Effect Editing” in Chapter 1 (Volume 1). Creation Creating new keyframes To create new keyframes, after recalling an empty register, use the following procedure to create and insert each new keyframe. Use the keyframe control block for carrying out the operation.
Page 26: Insertion
Insertion Inserting keyframes To insert a keyframe in an existing effect, use the following procedure in the keyframe control block. Press the [EDIT ENBL] button, turning it on. Stop the effect at the desired edit point. Create the image for the keyframe you want to insert. Press the [INS] button.
Page 27 Using image transformations or adding special effects, modify the keyframe. Press the [MOD] button. This modifies the keyframe. Modifying more than one keyframe simultaneously You can modify a number of keyframes simultaneously. There are three different cases for this operation. •...
Page 28 Press the [EDIT ENBL] button, turning it on. Stop the effect at any keyframe within the range to be modified. Carry out the necessary modifications. Press the [FROM TO] button, turning it on. The display in the numeric keypad control block shows the current keyframe number, followed by “TO.”...
Page 29 : Background A : Background B Effect execution Keyframe 1 Keyframe 2 Keyframe 3 Modify keyframe 2. (Changing the position of background B in the horizontal direction) Select keyframes 1 to 3 and modify simultaneously. Effect execution Keyframe 1 Keyframe 2 Keyframe 3 Result: The horizontal position of background B in keyframes 1 and 3 is now the same as that in keyframe 2.
Page 30: Deletion
Modifying the keyframes by holding down the [SHIFT] button and pressing the [MOD] button The modified parameter values are taken as relative values, which modify all of the selected keyframes. : Background A : Background B Effect execution Keyframe 1 Keyframe 2 Keyframe 3 Modify keyframe 2.
Page 31: Movement
Press the [EDIT ENBL] button, turning it on. Stop the effect at the desired edit point. When the edit point is on a keyframe, this is what you delete. If the edit point is between two keyframes, the previous keyframe is what you delete. To delete a number of keyframes in a single operation, press the [FROM TO] button, turning it on.
Page 32: Copying
Move the edit point to the position to which you want to move the keyframe. Press the [PASTE] button. This inserts the keyframe you have moved after the current keyframe. In constant duration mode, the moved keyframe overwrites the edit point. To insert the moved keyframe before a keyframe Hold down the [SHIFT] button, and press the [PASTE] button to insert the moved keyframe before the current keyframe.
Page 33: Pause
Pause To apply a pause to a keyframe, use the following procedure. Press the [EDIT ENBL] button, turning it on. Stop the effect on the keyframe to which you want to apply a pause. Press the [PAUSE] button. This applies a pause to the specified keyframe. Undoing an Edit Operation To undo a keyframe insert, modify, delete, or paste operation immediately after execution, press the [UNDO] button.
Page 34: Time Settings
Time Settings You can determine the execution time of an effect by setting either the keyframe durations or the effect duration. For details of keyframe duration and effect duration, see “Time Settings” in Chapter 1 (Volume 1). Setting the Keyframe Duration EDIT ENBL button KF DUR button EFF DUR button...
Page 35: Setting The Effect Duration
Setting the keyframe duration You can set the value of the keyframe duration independently for each keyframe, by the following method. Press the [EDIT ENBL] button, turning it on. Stop the effect on the keyframe for which you want to set the duration. The time from this keyframe to the following keyframe is what you set.
Page 36: Setting The Delay
Using the numeric keypad in the numeric keypad control block, enter the timecode value for the effect duration, as a maximum of six digits. For example, to set 3 minutes 7 seconds and 15 frames, enter 30715. You can also use the [TRIM] button to enter a difference value. (See “Entering a difference value”...
Page 37: Path Setting
Path Setting The term “path” refers to the specification of how interpolation is carried out from one keyframe to the next. For details of the notion of path, see “Paths” in Chapter 1 (Volume 1). Set keyframe paths in the Key Frame>Path menu. Accessing the Key Frame>Path menu In the top menu selection buttons of the menu control block, press [KEY FRAME], then select HF3 ‘Path.’...
Page 38 Changing the path type for Curve Use the following procedure. In the Path menu, press [M/E-1]. The M/E-1 menu appears. Press the Curve path type indication for the Key1 item that you want to change. A path selection window appears. Press the indication for the desired path type, to select it.
Page 39 The status area reflects the selected path type. At this point, depending on the setting for Curve, the effect for Hue and Xpt is also affected as shown in the following table. In the menu, the Hue and Xpt settings do not change, but the path type indication is dimmed out. Curve setting Hue change Xpt change...
Page 40 Press the indication for the desired path type, to select it. Xpt Hold off: When replaying a keyframe, change the inputs to the settings saved in memory. Xpt Hold on: When replaying a keyframe, do not change the inputs. Path Setting...
Page 41: Executing Effects
Executing Effects By means of the [RUN] button in the keyframe control block, you can play an effect as a continuously varying image. This is referred to as effect execution. See also “Effect Execution” in Chapter 1 (Volume 1). It is also possible to execute an effect from the device control block (see Chapter 2 (Volume 1)).
Page 42: Run Mode Setting
Executing an effect automatically Use the following procedure. Select the region in which you want to execute the effect, using the region selection buttons in the numeric keypad control block. (See step 2 (page 22) of “Recalling a register.”) With the numeric keypad, enter the number of the register in which the effect you want to execute is saved, and press the [ENTER] button to confirm.
Page 43 Press the [STOP NEXT KF] button, turning it on. Press the [RUN] button. This executes the effect as far as the next keyframe. When the [REV] button is lit, it is executed as far as the previous keyframe. Repeating an effect Use the following procedure.
Page 44: Saving Effects
Saving Effects When you recall an effect, the currently recalled effect is automatically saved in a register. This is referred to as the auto save function. You can disable the auto save function in a Setup menu. By means of the following operation, you can also specify a register and save an effect in it.
Page 45 To undo the saving of an effect Immediately after saving an effect, hold down the [STORE STATS] button and press the [UNDO] button to undo the save. Saving Effects...
Page 46: Register Operations In The Menus
Register Operations in the Menus Using the Effect menu, you can carry out the following effect register operations. • Status display • Register editing To display the Effect menu Press the top menu selection button [EFF] in the menu control block. Effect Status Display The Effect>Effect>Attribute menu displays the following information.
Page 47 register name, to display it in reverse video. To cancel a selection, press once more to return to the normal display. Note If you press a discontiguous register, this clears any previous selection. Be very sure to select the registers to be contiguous. When neither All nor Block is selected: You can use knob 1 to select a single register.
Page 48 Register Operations in the Menus...
Page 49: Chapter 14 Snapshots
Chapter 14 Snapshots Snapshot Operations From the Numeric Keypad Control Block ..50 Saving and Recalling Snapshots............51 Snapshot Operations in the Menus ............55 Setting Snapshot Attributes ............. 55 Snapshot Status Display ..............57 Setting Key Snapshot Attributes............58 Snapshot Register Editing ...............
Page 50: Snapshot Operations From The Numeric Keypad Control Block
Snapshot Operations From the Numeric Keypad Control Block The term “snapshot” refers to a function whereby the various settings required to apply a particular effect to an image are saved in memory as a set of data, for recall as required, to recover the original state. For an overview of snapshots, see “Snapshots”...
Page 51: Saving And Recalling Snapshots
Saving and Recalling Snapshots Snapshot operations with the numeric keypad control block use the following buttons. Display UNDO button SNAPSHOT button STORE STATS button SNAP SHOT DISS SHOT MASTR UNDO MCRO AUTO TRANS USER USER STORE TRANS STATS RATE TRIM STORE ENBL ENTER...
Page 52 Press the region selection button corresponding to the region for which you want to save, turning it on. You can select more than one region. [M/E 1], [P/P]: These select the corresponding M/E-1, and PGM/PST regions. [USER 1] , [USER 2]: These select the USER regions. [DME 1] to [DME 4]: These select DME channels.
Page 53 Press the [ENTER] button. This saves the snapshot, and the [STORE] button goes off. The [RCALL] and [STORE STATS] buttons light. To cancel a snapshot save operation After saving a snapshot, to cancel the save, hold down the [STORE STATS] button and press the [UNDO] button.
Page 54 Press the [ENTER] button. This recalls the specified snapshot, and the reference region name and recalled register number appear in the display. If you applied the effect dissolve or auto transition temporary attributes in step 4, the corresponding buttons go off. To cancel a snapshot recall operation After saving a snapshot, to cancel the recall, press the [UNDO] button.
Page 55: Snapshot Operations In The Menus
Snapshot Operations in the Menus You can also set snapshot or key snapshot attributes in the Snapshot menu, which also displays the status of the registers. To access the Snapshot menu, press the top menu selection button [SNAPSHOT] in the menu control block. In the Snapshot menu, as well as setting snapshot attributes, you can carry out editing operations on snapshots, including copy and delete.
Page 56 To apply the cross-point hold attributes Press [Xpt Hold], turning it on. The Snapshot>Attribute>Xpt Hold menu appears. The status area shows a list of the currently selected regions and bus names. To select the desired register, press the register number or register name in the status area, or turn knob 2.
Page 57: Snapshot Status Display
Snapshot Status Display The Snapshot>Attribute menu displays the following information. For details of how to access the Snapshot>Attribute menu, see page 55. Region name: The selected region name appears in the upper part of the list. Register number Register name Write-protected status: When the register is write-protected, an “L”...
Page 58: Setting Key Snapshot Attributes
When a GPI output is set: Displayed Attributes set character codes Port number GPI output is set for the port of the displayed number. Setting Key Snapshot Attributes Applying key snapshot attributes To apply an attribute to a key snapshot, use the following procedure. In the Snapshot menu, press VF5 ‘Key Snapshot’...
Page 59 • Copy: Copy the contents of one register to another register. • Move: Move the contents of one register to another register. • Swap: Swap the contents of two registers. • Delete: Delete the contents of a register. • Name: Attach a name to a register. Write-protecting the contents of the snapshot register Use the following procedure.
Page 60 Operation between regions Operation between regions is possible in the following cases. • Between the M/E-1 and P/P regions • Between the USER1 and USER2 regions • Betweeen two of the DME1 to DME4 (including Global) regions To select the desired registers, press on the register numbers or register names in the status area, or use the knobs.
Page 61 In the Snapshot menu, press VF2 ‘Snapshot’ and HF7 ‘Rename.’ The Snapshot>Snapshot>Rename menu appears. Using any of the following methods, select the snapshot register you want to name. • Press the desired register name in the register list. • Press the arrow keys to scroll the reverse video cursor. •...
Page 62 Snapshot Operations in the Menus...
Page 63: Chapter 15 Shot Box
Chapter 15 Shot Box Shot Box Register Creation..............64 Shot Box Execution................. 67 Shot Box Execution From the Numeric Keypad Control Block ..67 Shot Box Execution in the Utility/Shot Box Control Block.... 69 Shot Box Register Editing ..............71...
Page 64: Shot Box Register Creation
Shot Box Register Creation The term “shot box” refers to a function whereby for each specified region any snapshot or keyframe effect can be recalled simultaneously. For each region, any snapshot or keyframe effect number can be specified to be recalled. There is also a setting to enable or disable the auto run function.
Page 65 Using any of the following methods, select the register you want to create (or edit). • In the status area, press the [No] or [Name] for the shot box register you want to select, then press [EDIT]. • Use knob 1 to specify the register, and press [Edit]. Knob Parameter Adjustment...
Page 66 To return to the state before saving the setting In the <Store> group, press [Undo]. To run the settings to check them In the <Recall> group, press [Recall], to run the shot box. Shot Box Register Creation...
Page 67: Shot Box Execution
Shot Box Execution You can recall (and run) shot box registers from the following control blocks. This section describes the various methods of operation. • Numeric keypad control block (see page 67) • Utility/shot box control block (see page 69) Shot Box Execution From the Numeric Keypad Control Block Display...
Page 68 In the numeric keypad control block, press the [SHOT BOX] button, turning it on. • This allocates the numeric keypad control block to shot box operations. • The [RCALL] button lights amber. • The display shows the last recalled register number. With the numeric keypad buttons, enter the desired register number.
Page 69: Shot Box Execution In The Utility/Shot Box Control Block
Shot Box Execution in the Utility/Shot Box Control Block Bank selection buttons BANK BANK BANK BANK Memory recall buttons Utility/shot box control block (MKS-8033) In the utility/shot box control block, as the default setting the memory recall buttons have registers 1 to 96 allocated to banks 1 to 4. Bank Register allocation to memory recall buttons 1 to 24...
Page 70 Off: Register in which nothing is saved Lit orange: Register holding shot box settings Lit yellow: Last recalled register Press the memory recall button to which the shot box register you want to run is allocated. • The shot box execution is carried out. •...
Page 71: Shot Box Register Editing
Shot Box Register Editing You can carry out the following editing on shot box registers. • Lock: Write-protect the contents of the register. • Copy: Copy data from one register to another. • Move: Move data from one register to another. •...
Page 72 Shot Box Register Editing...
Page 73: Chapter 16 Engineering Setup
Chapter 16 Engineering Setup Setup for the Whole System..............75 Network Settings (Network Config Menu) ........75 System Settings (System Config Menu).......... 76 Setting the Signal Format and Screen Aspect Ratio (Format Menu) ..............78 Selecting the State After Powering On (Start Up Menu) ....79 Reset and Initialization (Initialize Menu) ........
Page 74 Setup Relating to DCU ................. 127 Settings Relating to Signal Inputs (Input Config Menu) ....127 GPI Input Setting (GPI Input Assign Menu) ......... 128 Signal Output Settings (Output Config Menu)......130 GPI Output Setting (GPI Output Assign Menu)......132 Setup Relating to Router Interface and Tally........
Page 75: Setup For The Whole System
Setup for the Whole System Carry out operations relating to setup in the Engineering Setup menu. To access the Engineering Setup menu, press the top menu selection button [ENG SETUP]. For an overview of setup, see “Setup” in Chapter 1 (Volume 1). Setting the unit ID When there are two switchers and connected DME units on the same network, it is necessary to set the unit ID on each device, as follows.
Page 76: System Settings (System Config Menu)
In the System>Network Config menu, press [Auto Config]. Turn the MKS-8010 System Control Unit off, then on again to restart the unit. This automatically checks all devices (excluding the DCU) connected to the Data LAN, and shows the results in the status area of the System>Network Config menu.
Page 77 Select the switcher to be controlled by the selected control panel, as follows. • If there is only one switcher on the network, in the <1st Switcher> group, set [SWR1] to ON, and in the <2nd Switcher> group, set [SWR2] to OFF.
Page 78: Setting The Signal Format And Screen Aspect Ratio (Format Menu)
In the <Setup Target> group, set the [System 1] or [System 2] button to ON, then carry out the setup. You can also set both to ON, and make the settings simultaneously on the two systems. Setting the Signal Format and Screen Aspect Ratio (Format Menu) To set the format, that is, the frame frequency and number of scan lines handled by each device, and the screen aspect ratio, use the System>Format menu.
Page 79: Selecting The State After Powering On (Start Up Menu)
In the System>Format>Active Line/Aspect menu, select one of the following from the <Screen Aspect> group. • 16:9 • 4:3 • Independ Set the screen aspect ratio separately for M/E, P/P, and USER on the switcher, and for each channel independently on the DME. If you selected [Independ] in step 1, select from the following.
Page 80 In the <Start Up Mode> group, select one of the following modes. Resume: When this is on, Resume mode is enabled. Custom: When this is on, Custom mode is enabled. For information about Resume mode and Custom mode, see “System Setup”...
Page 81: Reset And Initialization (Initialize Menu)
After selecting the devices the settings apply to, in the System>Start Up menu, press [Initial Status Define]. A confirmation message appears. Press [Yes]. This saves the initial status settings other than the “setup” settings for the selected devices in non-volatile memory within the respective devices. Reset and Initialization (Initialize Menu) To carry out a reset or memory initialization for a device, use the System>Initialize menu.
Page 82: Installation (Install Menu)
Installation (Install Menu) To install software or firmware in a device, use the System>Install menu. To display the Install menu In the Engineering Setup menu, select VF1 ‘System’ and HF6 ‘Install.’ The status area shows the device ID of each device and the version of the installed software.
Page 83: Setting The Date And Time
To display the Maintenance menu In the Engineering Setup menu, select VF1 ‘System’ and HF7 ‘Maintenance.’ In the status area, the current date and time, and details of the memory card appear. Setting the date and time For system date and time settings, use the following procedure. With the knobs, adjust the following parameters.
Page 84 Carrying out the primary setting To make the primary specification for a USB device, use the following procedure. In the System>Maintenance menu, using any of the following methods, select the USB device you want to set as primary. • Press directly on the list appearing in the status area. •...
Page 85: Setup Relating To Operations From The Control Panel
Setup Relating to Operations From the Control Panel Overall Control Panel Settings (Config Menu) To carry out the overall control panel settings, use the Panel>Config menu. To display the Config menu In the Engineering Setup menu, select VF2 ‘Panel’ and HF1 ‘Config.’ The status area shows the “Bank numbers 1 to 4”...
Page 86 For the selected Bank number, in the <M/E Operation> group, select one of the following. Enable: Enable panel display and operation of the operating bank. Disable: Enable only panel display, and disable operation of the operating bank. Inhibit: Disable both the panel display and operation of the operating bank.
Page 87 Linking switcher buses and routing switcher buses To provide links between the switcher and routing switcher buses, make the following settings as required. Matrix selection: Select the target of link setting from the eight matrices (1 to Matrix position definition: Set the start address and level for the source and destination on the S-Bus.
Page 88 Using any of the following methods, define the position of the matrix to be linked. • Press directly on the list appearing in the status area. • Press the arrow keys to scroll the reverse video cursor. • Turn the knobs to make the setting. Knob Parameter Adjustment...
Page 89 The sources are reassigned, and this is reflected in the status area. To make link bus settings For the link number selected in the External Bus Link menu, use the following procedure. In the Panel>Config>External Bus Link menu, press [Link Bus Adjust]. The Link>Link Bus Adjust menu appears.
Page 90: Cross-Point Settings (Xpt Assign Menu)
In the <Key Select> group, select the keyer to be linked to the transition of the master. Note Linking does not apply to a transition carried out with the downstream key control block. Cross-Point Settings (Xpt Assign Menu) To carry out the cross-point settings, use the Panel>Xpt Assign menu. To display the Xpt Assign menu In the Engineering Setup menu, select VF2 ‘Panel’...
Page 91 When assigning a video signal, press [Video] in the <Xpt> group. When assigning a key signal, press [Key]. Use any of the following operations to assign the signal. • Press directly on the list in the status area. • Press the arrow keys to move the reverse video cursor. •...
Page 92 can only carry out assignment of the video and key combinations in the Main table. You can select the table to be used for each of the following banks or buses. • M/E-1 and PGM/PST banks • Frame Memory Source 1/2 •...
Page 93 Knob Parameter Adjustment Setting values Sub Button No Sub cross-point button selection 1 to 128 • To disable operation of a button number, press [Inhibit]. Turn knob 3 to select the main cross-point button number to be assigned. Knob Parameter Adjustment Setting values Main Source No...
Page 94: Aux Delegation Buttons Settings (Aux Assign Menu)
AUX Delegation Buttons Settings (Aux Assign Menu) To carry out the settings of the AUX delegation buttons in the Aux bus control block, use the Panel>Aux Assign menu. To display the Aux Assign menu In the Engineering Setup menu, select VF2 ‘Panel’ and HF3 ‘Aux Assign.’ The left side of the status area shows the delegation numbers, and the list of buses set;...
Page 95: Interfacing With External Devices (Device Interface Menu)
Press [Set] to confirm the selection. Setting the AUX delegation button shift operation To set the operation mode of the rightmost button in the row of AUX delegation buttons, select one of the following in the <Shift Mode> group of the Panel>Aux Assign menu.
Page 96 : Apply the trigger on a change in the polarity of the input signal. (Level): When the input is low or high, the specified signal format or screen aspect ratio applies. (See “Carrying out level settings” (page 120).) No Operation: Apply no trigger on an input pulse. In the <Target>...
Page 97 Carrying out level settings To set the low level and high level, first set the trigger type to “Level,” then use the following procedure. In the Panel>Device Interface menu, select the action to be set, and press [H/L Set]. The H/L Set menu appears. Using any of the following methods, select the settings.
Page 98 : The trigger causes the relay contacts to be shorted or drives the output low, and holds this state for the specified pulse width. : Each time the trigger occurs, the relay contacts are alternately closed or opened, or the output is switched between high and low.
Page 99: Operation Settings (Operation Menu)
Press [Action Set] to confirm the action selection. The selected setting appears in the status area. Test firing the trigger To test fire the trigger, press [Test Fire]. This outputs a trigger from the selected output port. This is not output when the trigger type is “Status.”...
Page 100 Make the following settings as required. Effect recall mode: To select the initial keyframe state when an effect is recalled, select [Recall] (do not display the first keyframe) or [Recall&Rewind] (display the first keyframe) in the <Recall Mode> group. Automatic effect saving: To automatically save an effected when it is recalled after being edited, turn [Effect Auto Save] on.
Page 101: Screen Saver And Other Settings (Maintenance Menu)
everything here is set to OFF, then pressing the [ALL] button does not change the specification of the next transition. Interchanging the [AUTO TRANS] and [CUT] buttons: To interchange the [AUTO TRANS] and [CUT] buttons in the transition control block, press the [Auto Trans/Cut Swap] button, turning it on. Transition preview operation mode: For the operation mode of the [TRANS PVW] button, select [Lock] or [Hold] in the <Trans Pvw>...
Page 102 LCD: Adjust the brightness of the source name displays. The following description takes the LCD brightness as an example. Use a similar process for the other adjustments. In the Panel>Maintenance menu, press [LCD Brightness]. Adjust the following parameter. Knob Parameter Adjustment Setting values Brightness...
Page 103: Setup Relating To Switcher Processor
Setup Relating to Switcher Processor Settings for Switcher Configuration (Config Menu) To make settings for the switcher processor, use the Switcher>Config menu. To display the Config menu In the Engineering Setup menu, select VF3 ‘Switcher’ and HF1 ‘Config.’ The status area shows the output signal assignment for each operating bank. Adjusting the reference phase To adjust the switcher internal reference phase, adjust the following parameter in the Switcher>Config menu.
Page 104 To assign the output of each bank in Multi Program mode When you selected [Multi Program] in the procedure described in “Setting the operating mode” (page 103), use the following procedure. In the Switcher>Config menu, press [M/E Output Assign]. The M/E Output Assign menu appears. On the list in the status area, select the bank output to be assigned.
Page 105 In each of the <Key1> to <Key4> groups, select [Enable] or [Disable]. To set the key preview configuration You can make this setting at any time, regardless of the operation mode. In the Switcher>Config menu, press [K-PVW Config]. The K-PVW Config menu appears. The status area shows the key preview configuration for each bank.
Page 106: Signal Input Settings (Input Menu)
Signal Input Settings (Input Menu) For setup relating to signal inputs, use the Switcher>Input menu. To display the Input menu In the Engineering Setup menu, select VF3 ‘Switcher’ and HF2 ‘Input.’ The status area shows source numbers and source names, input signal phase, and through mode on/off setting.
Page 107: Signal Output Settings (Output Menu)
Press [Video Process], turning it on. Adjust the following parameters. Knob Parameter Adjustment Setting values −200.00 to +200.00 Video Gain Video signal gain −200.00 to +200.00 Y Gain Y signal gain −200.00 to +200.00 C Gain Chrominance signal gain −180.00 to +180.00 Hue Delay Hue delay −7.30 to +109.58...
Page 108 PGM/PST 1 to 6 DME Monitor Video DME Monitor Key [Aux Bus]: It is not possible to make duplicate assignments. Preset Edit Preview AUX 1 to 48 Using any of the following methods, select the output port number and signal to be assigned. •...
Page 109 Adjust the following parameters. Knob Parameter Adjustment Setting values White Clip Luminance signal white clip value 90.00 to 109.00 −6.85 to +10.00 Dark Clip Luminance signal dark clip value Chroma Clip Chrominance signal clip value 90.00 to 113.17 To set the values to the default values, press [Default]. Making vertical blanking interval adjustment and through mode settings Use the following procedure.
Page 110: Settings Relating To Video Switching (Transition Menu)
To enable the on/off settings made in the Misc menu, press [Safe Title], turning it on. Carry out either of the following operations. To display a box: Press [Box1] or [Box2], turning it on. In this case, carry out the following steps 4 and 5. To display a cross: Press [Cross], turning it on.
Page 111 • Press directly on the list appearing in the status area. • Press the arrow keys to scroll the reverse video cursor. • Turn knob 1 to make the selection. Knob Parameter Adjustment Setting values Bank M/E or P/P selection to which settings apply 1 to 4 The selected bank appears in reverse video.
Page 112: Settings Relating To Keys, Wipes And Frame Memory
In the Switcher>Transition menu, press [Transition Curve]. The Transition Curve menu appears. In the <Fader Curve> group, select the fader lever operation mode. Normal: The transition progress is linear, according to the fader lever position. (Factory default setting) Adv Tally Mode: When the fader lever is moved from the end of its travel, the tally is output slightly before the transition starts.
Page 113 In the <Show Key Enable> group, press the signal for which “show key” is enabled, turning it on. To set the time for which “show key” is held, press [Hold Time]. Adjust the following parameter. Knob Parameter Adjustment Setting values Hold Time Show key hold time 0 to 999 (frames)
Page 114: Settings Relating To Function Links (Link Menu)
Auto: When the pattern limit is released, the remainder of the transition is carried out automatically at a special-purpose transition rate. Manual: After the pattern limit is released, the transition waits for the next operation, then executes. Until you move the fader lever or press [AUTO TRANS], the transition is not executed.
Page 115 Knob Parameter Adjustment Setting values Link No Link number 1 to 64 Press [Link Bus Select]. The Link Bus Select menu appears. The status area lists the current setting status of the selected link and the buses that can be selected. In the <Bus Select>...
Page 116 Using any of the following methods, select the link source and link destination signals. • Press directly on the list appearing in the status area. • Press the arrow keys to scroll the reverse video cursor. • Turn the knobs to make the setting. Knob Parameter Adjustment...
Page 117 Knob Parameter Adjustment Setting values GPI Port GPI output port selection 1 to 8 Press [GPI Link Adjust]. The Link Bus Select menu appears. The status area shows the current setting state of the selected link, and a list of the selectable video names or button names, together with the GPI link Enable/Disable setting for each bus.
Page 118: Interfacing With External Devices (Device Interface Menu)
In the <Bus> group, select any of the following. Enable: Enable the GPI link setting for the selected bus. Disable: Disable the GPI link setting for the selected bus. All Enable: Enable the GPI link setting for all buses. To set the delay value Use the following procedure.
Page 119 Knob Parameter Adjustment Setting values Port Port selection 1 to 8 Selection of number for action to be 1 to 8 assigned In the <Trigger Type> group, select the trigger type. : Apply the trigger on a rising edge of an input pulse. : Apply the trigger on a falling edge of an input pulse.
Page 120 When Target is Common/Setup: FM Src1 Field Freeze, FM Src1 Frame Freeze, FM Src2 Field Freeze, FM Src2 Frame Freeze FM Src1 Freeze Off, FM Src2 Freeze Off User1 SS ? Recall, User1 EFF ? Recall, User1 EFF ? Recall & Run, User1 KF Run, User1 KF Stop, User1 KF Rewind User2 SS ? Recall, User2 EFF ? Recall, User2 EFF ? Recall &...
Page 121 In the Switcher>Device Interface menu, press [GPI Output]. The GPI Output menu appears. Using any of the following methods, select the settings. • Press directly on the list appearing in the status area. • Press the arrow keys to scroll the reverse video cursor. •...
Page 122 Knob Parameter Adjustment Setting values Action Action selection 1 to ... Reg No Register number 1 to 99 1 to 399 a) • Action list when the trigger type is other than “Status” When Source is M/E-1, M/E-2, or M/E-3: Cut, Auto Trans Key1 Cut, Key1 Auto Trans, Key2 Cut, Key2 Auto Trans, Key3 Cut, Key3 Auto Trans, Key4 Cut, Key4 Auto Trans Key1 SS ? Recall, Key2 SS ? Recall, Key3 SS ? Recall, Key4 SS ? Recall...
Page 123: Setup Relating To Dme
Setup Relating to DME Note To use DME requires the BKDS-9470 DME Board Set. Settings Relating to Signal Inputs (Input Menu) To make settings relating to DME input signals, display the DME>Input menu. To display the Input menu In the Engineering Setup menu, select VF4 ‘DME’ and HF1 ‘Input.’ The status area shows the input signal numbers and names, together with initial crop information.
Page 124: Interfacing With External Devices (Device Interface Menu)
To return the parameter values to their default values Press [Unity]. Setting an illegal color limit for matte signals To prevent an illegal color from being generated in a matte signal, in the DME>Input menu, press [Matte Illeg Col Limit], turning it on. Interfacing With External Devices (Device Interface Menu) To carry out setup relating to DME connections with external devices, display...
Page 125 Knob Parameter Adjustment Setting values Selection of number for action to 1 to 8 be assigned In the <Trigger Type> group, select the trigger polarity. : Apply the trigger on a rising edge of an input pulse. : Apply the trigger on a falling edge of an input pulse. : Apply the trigger on a change in the polarity of the input signal.
Page 126 In the DME>Device Interface menu, select the action to be set, and press [H/L Set]. The H/L Set menu appears. Using any of the following methods, select the settings. • Press directly on the list appearing in the status area. •...
Page 127: Setup Relating To Dcu
Setup Relating to DCU Settings Relating to Signal Inputs (Input Config Menu) The DCU parallel ports are assigned with the following priority sequence. 1. When external boxes are set, external boxes 1 to 4 are assigned from the first parallel port. 2.
Page 128: Gpi Input Setting (Gpi Input Assign Menu)
Releasing the assignment of a GPI input port Use the following procedure. In the DCU>Input Config menu, select what the setting applies to (DCU1 or DCU2) from the <DCU Select> group. Turn the knobs to adjust the following parameters. Knob Parameter Adjustment Setting values...
Page 129 : Apply the trigger on a change in the polarity of the input signal. (Level): When the input is low or high, the specified signal format or screen aspect ratio applies. (See “Carrying out level settings” (page 120).) No Operation: Apply no trigger on an input pulse. In the <Target Device>...
Page 130: Signal Output Settings (Output Config Menu)
• Action list when the trigger type is “Level” Simul, Custom , Format (frame/field rate, number of lines) (System Format, SWR Format, DME Ch1-Ch4 Format Aspect (System Aspect, SWR Aspect, M/E-1 Aspect, M/E-2 Aspect, M/E-3 Aspect, P/P Aspect, DME Ch1-Ch4 Aspect DME Ch1 Aspect, DME Ch2 Aspect, DME Ch3 Aspect, DME Ch4 Aspect No Action b) When knob 2 selection is “Snapshot”...
Page 131 To display the Output Config menu In Engineering Setup, select VF5 ‘DCU’ and HF3 ‘Output Config.’ The status area shows output port information. Assigning a GPI output port Use the following procedure. In the DCU>Output Config menu, select what the setting applies to (DCU1 or DCU2) from the <DCU Select>...
Page 132: Gpi Output Setting (Gpi Output Assign Menu)
In the <Parallel Output Assign> group, press [No Assign]. GPI Output Setting (GPI Output Assign Menu) To set the trigger type and so on for each GPI output, display the DCU>GPI Output Assign menu. To display the GPI Output Assign menu In Engineering Setup, select VF5 ‘DCU’...
Page 133 a) 1: Field 1, 2: Field 2, 3: Any In the <Source Device> group, select the action block. Using any of the following methods, select the action you want to set. • Press directly on the list appearing in the status area. •...
Page 134: Setup Relating To Router Interface And Tally
Setup Relating to Router Interface and Tally Router Interface Settings (Router Menu) In this system, the interface with a router (routing switcher) uses the S-Bus protocol. It is therefore necessary to assign inputs and outputs of the switcher and so on to an S-Bus space. To carry out this assignment, use the Router/Tally>Router menu.
Page 135 Level: Specify the level in the S-Bus space. Knob Parameter Adjustment Setting values Source Source start address 1 to maximum value Destination Destination start address 1 to maximum value Level Level 1 to 8 a) When the matrix size is Standard, the maximum value is 889. For the Compact size, the maximum value is 897.
Page 136: Tally Group Settings (Group Tally Menu)
In the External Box Assign menu, select [External box1] from the <Device> group. In the <Matrix Size> group, select [8×1]. Turn the knobs to make adjustments. Knob Parameter Adjustment Setting values Source Source start address 1 to 1017 Destination Destination start address 1 to 1024 Level Level...
Page 137: Wiring Settings (Wiring Menu)
Press [S-Bus Tally], turning it on or off. On: Enable the transfer of S-Bus tally information over the S-Bus. Off: Disable the transfer of S-Bus tally information over the S-Bus. Wiring Settings (Wiring Menu) When configuring a system in which the switcher inputs and outputs are connected to a router, it is necessary to set this connection configuration (referred to as “wiring”) in the S-Bus space.
Page 138 Set the source. Source From: Specify the source start address for the wiring configuration. Source Level: Specify the source level for the wiring configuration. Knob Parameter Adjustment Setting values Source From Source start address 1 to 1024 Source Level Source level 1 to 8 Press [Execute].
Page 139: Tally Generation Settings (Tally Enable Menu)
Tally Generation Settings (Tally Enable Menu) For settings relating to tally generation, use the Router/Tally>Tally Enable menu. To display the Tally Enable menu In the Engineering Setup menu, select VF7 ‘Router/Tally’ and HF4 ‘Tally Enable.’ The status area shows the tally generation settings. Making new tally generation settings Use the following procedure.
Page 140: Tally Copy Settings (Tally Copy Menu)
DCU2: Generate tally with reference to signal input to DCU2 port. Set the port number with the knob. With a knob or menu operation, select the tally input port number. Knob Parameter Adjustment Setting values Input No Tally input port number 1 to 102 Press [Execute].
Page 141 To display the Tally Copy menu In the Engineering Setup menu, select VF7 ‘Router/Tally’ and HF5 ‘Tally Copy.’ The status area shows the tally copy status. Making new tally copy settings Use the following procedure. In the Router/Tally>Tally Copy menu, select [New]. The New menu appears.
Page 142: Parallel Tally Settings (Parallel Tally Menu)
Knob Parameter Adjustment Setting values Copy To Copy-to source 1 to 1024 Press [Execute]. This updates the tally copy settings. Deleting tally copy settings Use the following procedure. In the Router/Tally>Tally Copy menu, using either of the following methods, select the tally copy whose settings you want to delete. •...
Page 143 • Press the arrow keys to scroll the reverse video cursor. • Turn the knobs to make the setting. Knob Parameter Adjustment Setting values Slot No Parallel tally slot number 2 to 6 Port No Parallel tally port number 1 to 54 Press [Set].
Page 144 • Press the arrow keys to scroll the reverse video cursor. • Turn the knobs to make the setting. Knob Parameter Adjustment Setting values Slot No Parallel tally slot number 2 to 6 Port No Parallel tally port number 1 to 54 Press [Clear].
Page 145: Simple Connection Of The Mks-8080/8082 Aux Bus Remote Panel
The setting does not change immediately. In the Engineering Setup>Router/Tally> Router menu, set the position of the DVS-9000 system in S-BUS space. Select the setting from SWR1 and SWR2, and set each of Source, Destination, and Level to 1.
Page 146: Setting Status Of The Mks-8080/8082 In Simple Connection
Since when using the simple connection the switcher and routing switcher cannot be connected in cascade, no route setting is required, and this is unset. O: SET AVAILABLE SOURCE/DESTINATION Set the source and destination ranges so that the DVS-9000 inputs and outputs can be selected. Y: SET DISPLAY MODES The DISPLAY MODES/PANEL FUNCTION setting is set to NORMAL.
Page 147: Chapter 17 Files
Chapter 17 Files Operations on Individual Files ............148 Selecting Regions ................149 Selecting the Recording Medium ..........149 Saving Files ................... 150 Recalling Files ................150 Copying Files................. 151 Moving Files.................. 152 Deleting Files................. 153 Renaming Files ................154 File Batch Operations................
Page 148: Operations On Individual Files
Operations on Individual Files You can save or recall the contents of an individual file or register. Carry out these operations in the File menu. To access the File menu In the menu control block, press the top menu selection button [FILE]. This explanation shows the example of the File>Effect, Snapshot menu in which you carry out keyframe effect and snapshot file operations, but the procedure is similar in the following menus.
Page 149: Selecting Regions
D1: device 1 related data D2: device 2 related data Selecting Regions You can carry out file operations on multiple regions simultaneously. However, since the setup, initial status, video process memory, key memory and frame memory operations are carried out independent of the regions, no region selection is required for them.
Page 150: Saving Files
Saving Files To save the contents of a register on the hard disk or memory card, use the following procedure. In the File menu, select VF3 ‘Effect, Snapshot’ and HF1 ‘Save.’ The File>Effect, Snapshot>Save menu appears. The top side of the status area shows the register name, and the bottom side shows the save destination.
Page 151: Copying Files
The File>Effect, Snapshot>Load menu appears. The top side of the status area shows the location where the file is saved, and the bottom side shows the register. If necessary, change the currently selected medium for recording ([HDD] or [Memory Card]). (See “Selecting the Recording Medium” (page 149).) In the <Category>...
Page 152: Moving Files
If necessary, change the currently selected medium for recording ([HDD] or [Memory Card]) for each of the copy source and copy destination. (See “Selecting the Recording Medium” (page 149).) In the <Category> group, select what the operation applies to. Effect: keyframe effect file Snapshot: snapshot file In the <Select>...
Page 153: Deleting Files
In the <Select> group, choose the method of selection, and in the status area, select the files. All: When this is on, all files are selected for the operation. Plural: When this is on, you can specify a number of files to which the operation will apply.
Page 154: Renaming Files
Press [Delete]. Renaming Files To change the name of a file on the hard disk or memory card, use the following procedure. In the File menu, select VF3 ‘Effect, Snapshot’ and HF6 ‘Rename.’ The File>Effect, Snapshot>Rename menu appears. The status area shows the list of files.
Page 155: File Batch Operations
File Batch Operations You can batch process all files or registers. Carry out these operations using the File>All/Directory menu. To access the File>All/Directory menu Press the top menu selection button [FILE], then select VF7 ‘All/Directory.’ Batch Saving Files To save the data of all registers to hard disk or memory card, use the following procedure.
Page 156 The Load menu appears. In the <Load From> group, select [HDD] (hard disk) or [Memory Card]. Select the files to which the operation applies. In the <Category> group, press the buttons for files you do not want to recall, removing them from the selection. For details of the data to which the operation applies, see “Files”...
Page 157: Chapter 18 Diagnosis
Chapter 18 DIAGNOSIS Not supported in version 1.30.
Page 159: Appendix
Appendix Wipe Pattern List.................. 160 Standard Wipes................160 Enhanced Wipes ................161 Rotary Wipes ................. 162 Mosaic Wipes ................163 Random/Diamond Dust Wipes ............165 DME Wipe Pattern List ............... 166 DME Wipe Patterns Available in One-Channel Mode ....166 DME Wipe Patterns Available in Two-Channel Mode....
Page 160: Wipe Pattern List
Wipe Pattern List Standard Wipes Wipe Pattern List...
Page 161: Enhanced Wipes
Enhanced Wipes Wipe Pattern List...
Page 162: Rotary Wipes
Rotary Wipes Wipe Pattern List...
Page 163: Mosaic Wipes
Mosaic Wipes Wipe Pattern List...
Page 164 Wipe Pattern List...
Page 165: Random/Diamond Dust Wipes
Random/Diamond Dust Wipes Wipe Pattern List...
Page 166: Dme Wipe Pattern List
DME Wipe Pattern List DME Wipe Patterns Available in One-Channel Mode Slide 1001 1002 1003 1004 1005 1006 1007 1008 Split 1011 1012 1013 DME Wipe Pattern List...
Page 167 Squeeze 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 Door 1041 1042 1043 1044 Flip tumble 1101 1102 DME Wipe Pattern List...
Page 168 Page turn 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 DME Wipe Pattern List...
Page 169 Page roll 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 User programmable DME 1901 1999 DME Wipe Pattern List...
Page 170: Dme Wipe Patterns Available In Two-Channel Mode
DME Wipe Patterns Available in Two-Channel Mode Slide 2601 2602 2603 2604 2605 2606 2607 2608 Squeeze 2621 2622 2623 2624 2625 2626 2627 2628 User programmable DME 2901 2999 DME Wipe Pattern List...
Page 171: Menu Tree
Menu Tree Recalling Menus This section details the menu structure, and shows the top menu selection buttons in the menu control block which are used to access the menus. Top menu selection buttons DISPL MENU FRAME COLOR COPY BKGD /MON COPY MISC SWAP...
Page 172 [M/E 1], [M/E 2], and [M/E 3] buttons M/E-1 VF1: Key1 HF1: Type (1111) Chroma Adjust (1111.1) VF2: Key2 Matte Adjust (1111.2) VF3: Key3 Key Priority (1173) VF4: Key4 HF2: Edge (1112) Matte Adjust (1112.1) Mix Pattern Select (1112.2) Zabton Adjust (1112.3) HF3: Main Mask (1113) Mask Pattern Select (1113.1) HF4: Sub Mask (1114)
Page 173: Pgm/Pst Menu
PGM/PST Menu [P/P] button PGM/PST VF1: DSK1 HF1: Type (1411) Chroma Adjust (1411.1) VF2: DSK2 Matte Adjust (1411.2) VF3: DSK3 Key Priority (1473) VF4: DSK4 HF2: Edge (1412) Matte Adjust (1412.1) Mix Pattern Select (1412.2) Zabton Adjust (1412.3) HF3: Main Mask (1413) Mask Pattern Select (1413.1) HF4: Sub Mask (1414) HF5: Processed Key (1415)
Page 174: Frame Memory Menu
Frame Memory Menu FRAME [FRAME MEM] button Frame Memory HF1: Select (2111) VF1: Recall HF2: Recall (2112) VF2: Edit HF1: Select (2121) VF3: Reposition/Lock HF2: Freeze (2122) VF4: File HF3: Composite (2123) Composite Adjust (2123.1) Pattern Select (2123.2) Field Conv (2123.3) HF6: Input Mask (2126) Pattern Select (2326.1) HF1: Select (2131)
Page 175: Aux/Mon Menu
AUX/MON Menu [AUX MON] button VF1: Aux Bus (2311) Copy/Swap Menu COPY [COPY SWAP] button SWAP VF1: Copy/Swap HF1: M/E (3111) HF2: Key (3112) HF3: Wipe (3113) HF4: DME Wipe (3114) HF5: Matte (3115) HF6: Color (3116) HF7: DME (3117) MISC Menu [MISC] button MISC...
Page 176: Dme Menu
DME Menu [DME] button VF1: Edge HF1: Border/Crop (4111) VF2: Video Modify HF1: Defocus/Blur (4121) VF3: Freeze HF2: Multi Move (4122) VF4: Non-Linear HF3: Color Modify (4123) Wave (4141.1) HF4: Mosaic (4124) Mosaic Glass (4141.2) HF1: Freeze (4131) Flag (4141.3) HF1: Type (4141) Twist (4141.4) VF5: Light/Trail...
Page 177: Device Menu
Device Menu [DEV] button Device VF2: P-BUS TimeLine (5321) Rewind Action (5321.1) VF3: VTR (5331) Key Frame Menu [KEY FRAME] button FRAME Key Frame HF1: Time Line (6111) HF3: Path (6113) M/E-1 (6113.1) M/E-2 (6113.2) M/E-3 (6113.3) P/P (6113.4) User1 (6113.5) User2 (6113.6) User3 (6113.7) User4 (6113.8)
Page 178: Effect Menu
Effect Menu [EFF] button VF2: Effect HF1: Attribute (6221) HF2: Lock (6222) HF3: Copy/Merge (6223) HF4: Move (6224) HF5: Swap (6225) HF6: Delete (6226) HF7: Rename (6227) Menu Tree...
Page 179: Snapshot Menu
Snapshot Menu SNAP [SNAP SHOT] button SHOT Snapshot VF2: Snapshot VF3: Wipe Snapshot VF4: DME Snapshot HF1: Attribute (6321) XPT Hold (6321.1) VF5: Key Snapshot HF2: Lock (6322) HF3: Copy (6323) HF4: Move (6324) HF5: Swap (6325) HF6: Delete (6326) HF7: Rename (6327) HF2: Lock (6332) HF3: Copy (6333)
Page 180: Shotbox Menu
Shotbox Menu SHOT [SHOT BOX] button Shotbox VF1: Register HF1: Store/Recall (6411) Edit (6411.1) HF2: Lock (6412) HF3: Copy (6413) HF4: Move (6414) HF5: Swap (6415) HF6: Delete (6416) HF7: Rename (6417) Menu Tree...
Page 181: File Menu
File Menu HF1: Save (7111) [FILE] button FILE HF2: Load (7112) File HF3: Copy (7113) VF1: Setup/Init HF4: Move (7114) HF5: Delete (7115) VF2: Key/V Proc Mem HF6: Rename (7116) VF3: Effect/Snapshot VF4: Wipe/DME/Key SS HF1: Save (7121) VF5: Shotbox HF2: Load (7122) VF7: All/Directory HF3: Copy (7123)
Page 182: Engineering Setup Menu
Engineering Setup Menu [ENG SETUP] button SETUP Engineering Setup VF1: System HF1: Network Config (7311) VF2: Panel HF2: System Config (7312) Panel Assign (7312.1) VF3: Switcher Switcher Assign (7312.2) VF6: Router/Tally to next page HF3: Format (7313) Active Line/Aspect (7313.1) Switcher Aspect (7313.2) DME Aspect (7313.3) HF4: Start Up (7314)
Page 183 [ENG SETUP] button SETUP Engineering Setup VF1: System to previous page VF2: Panel VF3: Switcher HF1: Config (7331) M/E Output Assign (7331.1) VF4: DME PGM Config (7331.2) VF5: DCU K-PVW Config (7331.3) VF6: Router/Tally HF2: Input (7332) Video Process (7332.1) HF3: Output (7333) Output Assign (7333.1) Video Clip (7333.2)
Page 184 Menu Tree...
Page 185: Index
Index for one-channel mode 166 Flip tumble 167 for two-channel mode Formatting a memory card 83 Attributes 58 Frame Memory menu 174 AUX bus remote panel 145 Door 167 Function links 114 AUX delegation button DSK auto drop function 113 settings 94 Duration mode setting 33 shift operation 95...
Page 186 operations 20 for DCU 130 path setting 37 Reference for switcher processor pause 33 output setting 110 register operations 46 phase adjustment 103 Simple connection 145 Region 23 Slide 166, 170 selection 149 Snapshot Register menu 179 M/E-1 to M/E-3 menus 171 operations in the menus register editing 58 Memory card formatting 83...
Page 187 preview mode setting 111 User programmable DME 169, 170 User-defined settings 80 Vertical blanking interval ad- justment 109 Video clip adjustment 108 process memory 112 switching settings 110 switching timing 103 Wipe pattern list 160 settings 112 Wiring settings 137 Write-protecting 59 Index...
Page 188 Index...
Page 189 The material contained in this manual consists of infor- mation that is the property of Sony Corporation and is intended solely for use by the purchasers of the equip- ment described in this manual. Sony Corporation expressly prohibits the duplication of...
Page 190 Sony Corporation B & P Company DVS-9000/9000SF Printed in Japan System (WW) 2002.08.13 2002 3-704-675-01 (1) Printed on recycled paper...

This manual is also suitable for:

Dvs-9000sf

Sony DVS-9000 User Manual

Chapter 11 DME Operations

Chapter 12 External Devices

Basic Operation for External Device Control

Control of P-BUS Devices

Chapter 13 Keyframe Effects

Sequence of Keyframe Operations

Recalling a Register

Specifying the Region and Edit Points

Creating and Editing Keyframes

Time Settings

Path Setting

Executing Effects

Saving Effects

Register Operations in the Menus

Chapter 14 Snapshots

Snapshot Operations from the Numeric Keypad Control Block

Snapshot Operations in the Menus

Chapter 15 Shot Box

Shot Box Register Creation

Shot Box Execution

Shot Box Register Editing

Chapter 16 Engineering Setup

Setup for the Whole System

Setup Relating to Operations from the Control Panel

Setup Relating to Switcher Processor

Setup Relating to DME

Setup Relating to DCU

Setup Relating to Router Interface and Tally

Simple Connection of the MKS-8080/8082 AUX Bus Remote

Panel

Simple Connection of the MKS-8080/8082 AUX Bus Remote Panel

Chapter 17 Files

Operations on Individual Files

File Batch Operations

Chapter 18 DIAGNOSIS

Appendix

Wipe Pattern List

DME Wipe Pattern List

Menu Tree

Index

Quick Links

Related Manuals for Sony DVS-9000

Summary of Contents for Sony DVS-9000

This manual is also suitable for:

Table of Contents