Page 1
47W 4 VOL ADJ Plastic cabinet assy Screw set Lever (A02-1497-13) (N99-1704-05) (D10-4562-04)x2 (D10-4621-04)x2 : KDC-5090B Mounting hardware assy DC cord Antenna adaptor (J21-9641-13) (E30-4944-05): KDC-5090BY (T90-0523/0534-05) (E30-4958-05): KDC-5090B The MECHANISM OPERATION DESCRIPTION is the same as model KDC-S3007 and KDC-5050RG.
KDC-5090B/BY CONTENTS BLOCK DIAGRAM ..............3 COMPONENT DESCRIPTION ..........4 MICROCOMPUTER’S TERMINAL DESCRIPTION ....6 TEST MODE ................8 ATTENTION ................10 PC BOARD ................11 CD PLAYER UNIT (X32-5010-00) ........11 ELECTRIC UNIT (X25-87X2-7X) ........13 SWITCH UNIT (X13-99XX-X4) ........... 14 SCHEMATIC DIAGRAM............
KDC-5090B/BY COMPONENT DESCRIPTION SWITCH UNIT (X13-99XX-X4) Ref. No. Component Name Application / Function Operation / Condition / Compatibility LC75808W LCD driver with the key matrix RS-171 Remote sensor IC DTA114EUA or KRA302 Key-permission SW For the key scanning start 2SD2114K Red LED SW When a base goes Hi, RED LEDs are turned on.
Page 5
KDC-5090B/BY COMPONENT DESCRIPTION Ref. No. Component Name Application / Function Operation / Condition / Compatibility 2SB1184 While Q22’s base goes Hi, AVR outputs +10.5V. ILL +B AVR 2SC4081 or 2SD1819A Works during POWER ON mode with a panel attached to the set.
KDC-5090B/BY MICROCOMPUTER’S TERMINAL DESCRIPTION IC1 (ELECTRIC UNIT : X25-87X2-7X) Pin No. Pin Name Description Processing Operation AM+B AM+B control Hi : During AM reception FM+B FM+B control Hi : During FM reception, Hi : Last FM mode (only RDS model)
Page 7
KDC-5090B/BY MICROCOMPUTER’S TERMINAL DESCRIPTION Pin No. Pin Name Description Processing Operation 48~51 Not used (N.C.) ILL-ON Illumination AVR on/off control output Hi : POWER ON mode except panel detached or panel mask position M-MUTE L Mute request (Lch) from CD MECHA. MI-COM.
KDC-5090B/BY TEST MODE 1. How to enter the test mode • Each press of the Track Up key jumps to the following While holding the FM and Preset 6 keys, reset the unit. track numbers: No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →...
Page 9
KDC-5090B/BY TEST MODE 10. Special display when the display is all on 2. Method of registration of the security code after EEPROM (Tuner Unit Ass’y) replacement (Code Pressing the Preset keys while the power is ALL OFF dis- security model) plays the following information.
KDC-5090B/BY TEST MODE / ATTENTION ATTENTION 4. Method of initializing the Mask key (How to reset the unit from the Mask key approved condition Assembly pf FPC (Flexible PC board) onto Roller to the factory condition) ass’y 1) Enter the test mode. (See 1. How to enter the test mode) Turn Roller ass’y by 2 times.
Page 15
• DC voltages are as measured with a high impedance voltmeter. Values may L DATAS L DATAS GND LINE L DATAL L DATAL vary slightly due to variations between individual instruments or/and units. B LINE DIMMER DIMMER N.C. N.C. REMO REMO N.C. N.C. KDC-5090B/5090BY (1/2) D GND D GND S.GND KDC-5090B/BY...
Page 17
B LINE CAUTION : For continued safety, replace safety critical components only with manufacturer's recommended parts (refer to parts list). KDC-5090B/BY Indicates safety critical components. To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer.
Page 18
KDC-5090B/BY EXPLODED VIEW (MECHANISM) M1.7x2.5 N09-4249-05 2x3.5 N09-4172-05 M1.7x4 N09-4202-05 M2x2 N38-2020-46 N09-4294-05 WASHER 1.2 N19-2023-04 WASHER 1.6 N19-2058-04 WASHER 1.6 N19-2093-04 M2x2 N39-2020-46 DPU1 (X32-5010-00) Parts with the exploded numbers larger than 700 are not supplied.
G01-2773-14 EXTENSION SPRING G01-2774-34 EXTENSION SPRING G01-2775-04 TORSION COIL SPRING G01-2776-14 TORSION COIL SPRING G01-2777-24 TORSION COIL SPRING G01-2844-04 EXTENSION SPRING G02-1231-04 FLAT SPRING G02-1232-24 FLAT SPRING G02-1241-24 FLAT SPRING E : KDC-5090B E1 : KDC-5090BY Indicates safety critical components.